Motologic 038128063Q User manual

038128063Q
Brand
Motologic
Model
038128063Q
Type
User manual

Motologic 038128063Q is a specialized tool designed to efficiently remove and install the intake flap motor with intake manifold runner position sensor on Audi vehicles. It allows for precise removal of the engine cover, disconnection of vacuum lines and electrical connections, and careful detachment of the linkage from the intake flap motor. The tool also facilitates the reinstallation process, ensuring proper tightening specifications as per the vehicle's manufacturer guidelines.

Motologic 038128063Q is a specialized tool designed to efficiently remove and install the intake flap motor with intake manifold runner position sensor on Audi vehicles. It allows for precise removal of the engine cover, disconnection of vacuum lines and electrical connections, and careful detachment of the linkage from the intake flap motor. The tool also facilitates the reinstallation process, ensuring proper tightening specifications as per the vehicle's manufacturer guidelines.

8/31/2021
2006 Audi A3 • MotoLogic
https://www.motologic.com/car/audi_2006_8p_a3/article/4c5175459935c7376342f57d96e8de5b?returnPath=%2Fcar%2Faudi_2006_8p_a3%2Fsearch%3Fkeywords%3DRUNNER
1/3
Report a problem with this article
Intake Flap Motor with Intake Manifold Runner Position Sensor → Removal and
Installation → Fuel Injection and Ignition
The information in this article comes from a service manual containing information that applies to the following engine
codes: AXX, BHZ, BPY, BWA, BZC, CDLA, CDLC.
Section Info:
Multiport Fuel Injection
5 Removal and Installation
5.6 Intake Flap Motor with Intake Manifold Runner Position Sensor
↻
8/31/2021
2006 Audi A3 • MotoLogic
https://www.motologic.com/car/audi_2006_8p_a3/article/4c5175459935c7376342f57d96e8de5b?returnPath=%2Fcar%2Faudi_2006_8p_a3%2Fsearch%3Fkeywords%3DRUNNER
2/3
For the installation location of the intake flap motor -V157- , see
Intake Manifold, Assembly Overview. Refer to
⇒ “2.3 Intake Manifold Assembly Overview”, page 14 .
Special tools and workshop equipment required
1
♦Commercially available / 4 inch ratchet
♦ TORX 30
Removing
– Remove engine cover. Refer to
⇒ “5.1 Engine Cover with Air Filter Element”, page 28 .
– Disconnect the vacuum lines -arrows-.
↻
8/31/2021
2006 Audi A3 • MotoLogic
https://www.motologic.com/car/audi_2006_8p_a3/article/4c5175459935c7376342f57d96e8de5b?returnPath=%2Fcar%2Faudi_2006_8p_a3%2Fsearch%3Fkeywords%3DRUNNER
3/3
– Remove the bracket -arrow- for the harness.
– Disconnect the electrical connections -1, 2 and 3-.
– Remove bracket for cable connector -arrows- from coolant
pipe.
Note
Open the nut with the left arrow just enough so that the bracket
can moved to the side.
– Carefully pry off linkage from intake flap motor -4-.
– Remove intake flap motor -5- .
Note
The illustration shows the intake manifold removed.
Installing
– Installation is in reverse order.
• Tightening specification, refer to
⇒ “2.3 Intake Manifold Assembly Overview”, page 14
  • Page 1 1
  • Page 2 2
  • Page 3 3

Motologic 038128063Q User manual

038128063Q
Brand
Motologic
Model
038128063Q
Type
User manual

Motologic 038128063Q is a specialized tool designed to efficiently remove and install the intake flap motor with intake manifold runner position sensor on Audi vehicles. It allows for precise removal of the engine cover, disconnection of vacuum lines and electrical connections, and careful detachment of the linkage from the intake flap motor. The tool also facilitates the reinstallation process, ensuring proper tightening specifications as per the vehicle's manufacturer guidelines.

Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents