Assembly Instructions: 3604-L (Duncan)
IMPORTANT:
• ALL INSTALLATION WORK SHOULD BE DONE BY ACCREDITED PROFESSIONAL.
• SHUT OFF POWER SUPPLY AT FUSE OR CIRCUIT BREAKER!
• USE ONLY THE SPECIFIED BULBS. DO NOT EXCEED THE MAXIMUM WATTAGE!
PREPARING FOR INSTALLATION
Carefully remove all of the contents from the carton. See the
important notes above. Shut off the power at the circuit breaker
andcompletelyremovetheoldxturefromthewall,including
theoldmountingstrap.
Fromthepartsbagremovethemountingstrapassembly.
MountingStrap(B)containsseveralpairsofthreadedholes.
Findthepairofholesthatmatchesthespacingoftheholesin
canopy(G).Threadtwoofmountingscrews(C)intomounting
strap(B).Whenplacedoverthemountingstrap,thethreaded
endsofmountingscrews(C)willprotrudethroughtheholesof
canopy(G).Placemountingstrap(B)overthejunctionboxso
thatmountingscrews(C)arevertical.Attachmountingstrap(B)
tothejunctionboxusingtwoofmountingscrews(A).Tighten
the screws securely.
ASSEMBLING THE FIXTURE
Bymeasuringdeterminecorrectnumberofrodsneededfor
properhangingheight.*Thisxtureincludes4rods(6”,12”,12”,
12”).Toshortenthexture,slidetheexcessrodsoffthewires.
Tolengthen,addadditionalrodstothewires.
Pullthexture’swiresthroughrods(H,I,J,K)untiltautand
threadtherodstogether.Thenthreadthebottomrodontothe
threadsofxturebody(L).Threadthetoprodtothethreadsof
theswiveljointoncanopy(G).
CONNECTING THE WIRES
Haveanassistantsupportthextureweightwhilecompleting
thewiring.Cutawayexcesswires.Threadthexture’swires
throughcanopy(G).Attachthexture’swirestothepower
supplywiresfromthejunctionbox.Connectblacktoblack(or
smooth);whitetowhite(orribbed);groundtoground(greenor
copper).Twisttheendsofthewirepairstogether.Thentwiston
a wire connector. Make sure all twists are in the same direction.
Ifthereisnogroundwire(greenorcopper)fromthejunction
box,locatethegroundscrewonmountingstrap(B)andwrap
thexture’sgroundwirearoundthegreengroundscrew.Usea
screwdrivertosecurethegroundscrewontomountingstrap(B).
Tuckallwiresneatlyintothejunctionbox.
FINISHING THE INSTALLATION
Pushcanopy(G)uptotheceilingandovermountingstrap(B)
sothatmountingscrews(C)protrudethroughcanopy(G).Twist
deconuts(F)ontothethreadsofmountingscrews(C)tosecure
the canopy in place.
Holdshade(M)uptoxturebody(Y)andslidespacer(Q)onto
thesocket.Secureinplacebythreadingsocketring(R)ontothe
socketuntiltight.
Installlightbulb(notincluded)inaccordancewiththexture’s
specications.Donotexceedthemaximumrecommended
wattage.
Placediffuser(O)intothemetalring(P).Thenraisemetalring(P)
upbeneathshade(M).Placescrews(N)througheachholeon
thesideofmetalring(P).Twistuntiltight.
Your installation is now complete. Turn on the power and test
thexture.
CLEANING TIPS
Treat the xture gently! Regular cleaning will reduce the need for deep cleaning. For regular cleaning, turn off the light and wipe down the
xture with a clean lint-free cotton or microber cloth. Never spray cleaner directly onto the xture.
For Customer Service, contact
the place of purchase to arrange
for replacement parts.
BLACK
(Hot)
WHITE
(Neutral)
GREEN
(Ground)
HOUSE WIRES
SMOOTH
(Or Black)
FIXTURE WIRES
RIBBED
(Or White)
BARE COPPER
(Or Green)
H
A
O
Y
F
C
B
G
Q
M
JUNCTION
BOX
I
J
K
R
P
L
N