Golden Lighting 2073-SF GMT Operating instructions

Assembly Instructions: 2073-SF

IMPORTANT:

• ALL INSTALLATION WORK SHOULD BE DONE BY ACCREDITED PROFESSIONAL.

• SHUT OFF POWER SUPPLY AT FUSE OR CIRCUIT BREAKER!

• USE ONLY THE SPECIFIED BULBS. DO NOT EXCEED THE MAXIMUM WATTAGE!

PREPARING FOR INSTALLATION

Remove all of the contents from the carton. See the important

notes above. Shut off the power at the circuit breaker and

completelyremovetheoldxturefromtheceiling,includingthe

oldmountingstrap.

Mountingstrap(B)containsseveralpairsofthreadedholes.

Findthepairofholesthatmatchesthespacingoftheholes

onthejunctionbox.Twoofmountingscrews(A)shouldbe

attachedtomountingstrap(B).Youmayneedtotighten

nuts(C)whichholdthesescrewsinplace.Placemounting

strap(B)overthejunctionboxsothatmountingscrews(A)are

pointingdown.Securemountingstrap(B)tothejunctionbox

withmountingscrews(D)andascrewdriver.Tightenthescrews

securely.

Placethexture’ssocketcluster(R)onaatsurface.Rod(N)is

onthexture’swires,butnotattachedtothebodyofthexture.

Passthexture’swiresthroughrod(N)andpullthewiresuntil

taut.Twistrod(N)ontothexture’sbodyuntilsecure.Attachrods

(M)tothehooksonthexture’sbody.Haveanassistantholdthe

canopyabovethexture’sbody,thenattachrod(N)tocanopy

(F).Attachrods(M)tothehooksoncanopy(F).Pushthewires

throughthecenterofcanopy(F).

CONNECTING THE WIRES

Haveanassistantorassistantssupportthexture’sweightwhile

completingthewiring.Cutawaytheexcesswires.Attachthe

xture’swirestothepowersupplywiresfromthejunctionbox.

Connectblacktoblack(orsmooth);whitetowhite(orribbed);

groundtoground(greenorcopper).Twisttheendsofthewire

pairstogether,thentwistonawireconnector.Makesureall

twistsareinthesamedirection.Ifthereisnogroundwire(green

orcopper)fromthejunctionbox,locategroundscrew(E)on

mountingstrap(B)andwrapthexturegroundwirearoundthe

greengroundscrew(E).Useascrewdrivertosecureground

screw(E)ontothemountingbracket.Tuckallwiresneatlyintothe

junctionbox.

FINISHING THE INSTALLATION

Raisecanopy(F)totheceiling.Positionmountingscrews(A)so

thattheyprotrudethroughtheopeningsofcanopy(F).Secure

canopy(F)inplacewithdecorativenuts(G).

Slidecandlesleeves(Q)overthesockets.Installlightbulbs(O)

(notincluded)inaccordancewiththexture’sspecications.

Placeglassshade(S)ontobottomcap(T).Raiseglassshade

(S)andbottomcap(T)upbeneathbottomassembly(R).Twist

bottomnial(U)ontothethreadsofbottomassembly(R).Tighten

securely.

Your installation is complete. Turn on the power and test the

xture.

CLEANING TIPS

Treat the xture gently! Regular cleaning will reduce the need for deep cleaning. For regular cleaning, turn off the light and wipe down the

xture with a clean lint-free cotton or microber cloth. Never spray cleaner directly onto the xture. For deep cleaning, turn off the light

and remove the glass prior to cleaning. Hand wash glass with warm water and mild detergent. Dry with a lint-free or microber cloth.

FLUSH

INSTALLATION

BLACK

(Hot)

WHITE

(Neutral)

GREEN

(Ground)

HOUSE WIRES

SMOOTH

(Or Black)

FIXTURE WIRES

RIBBED

(Or White)

BARE COPPER

(Or Green)

For Customer Service, contact the

place of purchase to arrange for

replacement parts.

IMPORTANT:

• ALL INSTALLATION WORK SHOULD BE DONE BY ACCREDITED PROFESSIONAL.

• SHUT OFF POWER SUPPLY AT FUSE OR CIRCUIT BREAKER!

• USE ONLY THE SPECIFIED BULBS. DO NOT EXCEED THE MAXIMUM WATTAGE!

PREPARING FOR INSTALLATION

Remove all of the contents from the carton. See the important

notes above. Shut off the power at the circuit breaker and

completelyremovetheoldxturefromtheceiling,includingthe

oldmountingstrap.

Fromthepartsbagremovethemountingstrapassembly

forpendants.Oneendofnipple(G)shouldbeattachedto

mountingstrap(A)withhexnuts(C,D)inplace.Theotherend

shouldhavecanopyloop(H)attached.Findthepairofholes

onmountingstrap(A)thatmatchesthespacingoftheholeson

thejunctionbox.Attachmountingstrap(A)tothejunctionbox

usingmountingscrews(B)andascrewdriver.Tightensecurely.

Unscrewcanopyloopcollar(I)fromcanopyloop(H).Pass

canopy(D)overthemountedcanopylooptotesttheheight.

Approximatelyhalfofthecanopyloop’sexteriorthreadsshould

beexposed,andthecanopyloopcollarshouldtsnuglyonto

thecanopyloop.Removecanopy(D)andadjusttheheightof

nipple(G)andcanopyloop(H)untilthedesiredheightisreached.

Placethexture’ssocketcluster(R)ontoaatsurface.Rod

(N)isonthexture’swires,butnotattachedtothebodyofthe

xture.Passthexture’swiresthroughrod(N)andpullthewires

untiltaut.Twistrod(N)ontothexture’sbodyuntilsecure.By

measuring,determinethecorrectnumberofchainlinksneeded

forproperhangingheight.Ifnecessary,useapairofpliersto

openandremoveanyexcesschain.Attachonechainconnector

(K)toeachendofchain(J).Useoneofchainconnectors(K)to

attachchain(J)totoploop(L)andclosethechainconnector.

Haveanassistantattachrods(M1)tothehooksonthexture

bodythenattachthehooksofrods(M1)totoploop(L).Hook

theendofrod(N)ontotoploop(L).Pullthewiresthroughtop

loop(L).Feedthexture’swiresupthroughthechain(every

threelinksorso),pullingthewiresuntiltaut.Slidecanopyloop

collar(H)andcanopy(G)ontothechain/wires.Usethefreechain

connector(K)toattachchain(J)tocanopyloop(H).

CONNECTING THE WIRES

Haveanassistantsupportthexture’sweightwhilecompleting

thewiring.Cutawaytheexcesswires.Threadthexture’swires

throughcanopyloop(H)andnipple(G).Attachthexture’swires

tothepowersupplywiresfromthejunctionbox.Connectblack

toblack(orsmooth);whitetowhite(orribbed);groundtoground

(greenorcopper).Twisttheendsofthewirepairstogether,then

twist on a wire connector. Make sure all twists are in the same

direction.Ifthereisnogroundwire(greenorcopper)fromthe

junctionbox,locategroundscrew(F)onmountingstrap(A)and

wrapthexture’sgroundwirearoundthegreengroundscrew(F).

Useascrewdrivertosecuregroundscrew(F)ontothemounting

bracket.Tuckallwiresneatlyintothejunctionbox.

FINISHING THE INSTALLATION

Raisecanopy(D)totheceiling.andslidecanopyloopcollar

(I)upbeneaththecanopy.Tightlythreadcanopyloopcollar(I)

ontocanopyloop(H)tosecurecanopy(G)inplace.Slidecandle

sleeves(Q)overthesockets.Installlightbulbs(O)(notincluded)

inaccordancewiththexture’sspecications.Placeglassshade

(S)ontobottomcap(T).Raiseglassshadeupbeneathbottom

assembly(R).Twistbottomnial(U)ontothethreadsofbottom

assembly(R).Tightensecurely.