H3C S7506E-S Installation, Quick Start

Brand: H3C

Model: S7506E-S

Type: Installation, Quick Start

This manual is also suitable for

H3C S7500E Switch Series

Installation Quick Start

New H3C Technologies Co., Ltd.

http://www.h3c.com.hk

Document version: 6PW102-20170430

No part of this manual may be reproduced or transmitted in any form or by any means without prior

written consent of New H3C Technologies Co., Ltd.

Trademarks

H3C, , H3CS, H3CIE, H3CNE, Aolynk, , H

Care, , IRF, NetPilot, Netflow,

SecEngine, SecPath, SecCenter, SecBlade, Comware, ITCMM and HUASAN are trademarks of New

H3C Technologies Co., Ltd.

All other trademarks that may be mentioned in this manual are the property of their respective owners

Notice

The information in this document is subject to change without notice. Every effort has been made in the

preparation of this document to ensure accuracy of the contents, but all statements, information, and

recommendations in this document do not constitute the warranty of any kind, express or implied.

Environmental protection

This product has been designed to comply with the environmental protection requirements. The storage,

use, and disposal of this product must meet the applicable national laws and regulations.

Contents

Installation quick start ·················································································································································· 1

Chassis views and technical specifications ···················································································································· 1

Chassis views ···························································································································································· 1

Technical specifications ··········································································································································· 2

Safety recommendations ·················································································································································· 4

Examining the installation site ········································································································································· 5

Installing the switch ··························································································································································· 5

Attaching the slide rails to the rack ························································································································ 5

Installing cage nuts ··················································································································································· 6

Installing mounting brackets and cable management brackets ··········································································· 8

Installing the switch in the rack ······························································································································· 9

Grounding the switch ············································································································································ 10

Installing FRUs ························································································································································ 11

Installing a power module ···································································································································· 12

Connecting power cords ······································································································································ 14

Accessing the switch for the first time ·························································································································· 18

Connecting the console cable ······························································································································ 18

Setting terminal parameters ·································································································································· 18

Powering on the switch ········································································································································· 19

Obtaining documentation ············································································································································· 20

Index ··········································································································································································· 21

Installation quick start

This installation quick start provides basic instructions for installing an S7500E switch. For more

information about the installation procedure, see H3C S7500E Switch Series Installation Guide.

The installation procedure is similar for all S7500E switch models. This installation quick start uses the

S7503E switch as an example.

NOTE:

The figures in this installation quick start are for illustration only.

Chassis views and technical specifications

Chassis views

Figure 1 Chassis

Figure 2 S7503E switch front panel

(1) MPU slots (2) LPU slots

(3) Power module slots (4) Fan tray slot

Technical specifications

Table 1 Chassis dimensions

Model Hei

ht Width

S7502E 175 mm (6.89 in) (4 RU) 436 mm (17.17 in) 420 mm (16.54 in)

S7503-S 175 mm (6.89 in) (4 RU) 436 mm (17.17 in) 420 mm (16.54 in)

S7503E 441 mm (17.36 in) (10 RU) 436 mm (17.17 in) 420 mm (16.54 in)

S7506E-S 575 mm (22.64 in) (13 RU) 436 mm (17.17 in) 420 mm (16.54 in)

S7506E (non-PoE) 575 mm (22.64 in) (13 RU) 436 mm (17.17 in) 420 mm (16.54 in)

S7506E 575 mm (22.64 in) (13 RU) 436 mm (17.17 in) 420 mm (16.54 in)

S7506E-V 930 mm (36.61 in) (21 RU) 436 mm (17.17 in) 420 mm (16.54 in)

S7510E 708 mm (27.87 in) (16 RU) 436 mm (17.17 in) 420 mm (16.54 in)

Table 2 Power module specifications

Model Rated voltage range

Maximum output

ower

Support for PoE

Maximum PoE

out

ower

PSR320-A

100 VAC to 240 VAC @

50/60Hz

300 W No N/A

PSR320-D –48 VDC to –60 VDC 300 W No N/A

PSR650-A

100 VAC to 240 VAC @

50/60Hz

650 W No N/A

PSR650-D –48 VDC to –60 VDC 650 W No N/A

Model Rated voltage range

Maximum output

ower

Support for PoE

Maximum PoE

out

ower

PSR650C-12A

100 VAC to 240 VAC @

50/60Hz

650 W No N/A

PSR650C-12D –48 VDC to –60 VDC 650 W No N/A

PSR1400-A

100 VAC to 240 VAC @

50/60Hz

1150 W (110

VAC)

No N/A

1400 W (220

VAC)

No N/A

PSR1400-D –48 VDC to –60 VDC 1400 W Yes 6720 W

PSR1400-12D1 –48 VDC to –60 VDC 1400 W No N/A

PSR2800-ACV

100 VAC to 240 VAC @

50/60Hz

1150 W (110

VAC)

Yes 1150 W

1400 W (220

VAC)

Yes 1400 W

PSR6000-ACV

100 VAC to 240 VAC @

50/60Hz

1150 W (110

VAC)

Yes

• One PoE input:

1200 W

• Two PoE inputs:

2400 W

• Three PoE

inputs: 3600 W

1400 W (220

VAC)

Yes

• One PoE input:

1800 W

• Two PoE inputs:

3600 W

• Three PoE

inputs: 5300 W

Table 3 Power module and chassis compatibility matrix

Power module

Chassis

S7502E

S7503E

-S

S7503

S7506E

-S

S7506E

(non-PoE)

S7506E

-V

S7510

PSR320-A

— — — — — —

PSR320-D

— — — — — —

PSR650-A

{

—

PSR650-D

{

—

PSR650C-12A — —

—

PSR650C-12D — —

—

PSR1400-A — —

PSR1400-D — —

PSR1400-12D1 — —

PSR2800-ACV — —

—

Power module

Chassis

S7502E

S7503E

-S

S7503

S7506E

-S

S7506E

(non-PoE)

S7506E

-V

S7510

PSR6000-ACV — —

—

NOTE:

• "z" indicates that the power module can be directly installed on the chassis.

• "{" indicates that you must first install a power module adapter on the chassis and then install the power

module on the power module adapter.

• "—" indicates that the power module cannot be installed on the chassis.

Safety recommendations

To avoid equipment damage or bodily injury caused by improper use, read the following safety

recommendations before installation. Note that the recommendations do not cover every possible

hazardous condition.

• To prevent ESD damage, always wear an ESD wrist strap and make sure it is reliably grounded

before you touch the switch, cards, or PCB.

• Do not install the switch, FRUs, or cables when the switch is powered on.

• To avoid equipment damage or bodily injury, make sure the switch is reliably grounded before

powering on the switch.

• To ensure good ventilation, install a blank filler panel in an unused slot.

Figure 3 Attaching an ESD wrist strap

Examining the installation site

The switch can only be used indoors. To make sure the switch operates correctly and prolong its service

lifetime, the installation site must meet the requirements for load-bearing, temperature, humidity,

cleanness, EMI, grounding power module, ventilation, and space. For more information, see H3C

S7500E Switch Series Installation Guide.

Installing the switch

Attaching the slide rails to the rack

1. Read the signs on the slide rails to identify the left and right slide rails and their front ends, as

shown in Table 4.

Table 4 Description f

or signs on the slide rails

n Meanin

Remarks

F/L Front end of the left slide rail Mount this end to the front left rack post.

F/R Front end of the right slide rail Mount this end to the front right rack post.

2. Mark the installation position on the rack for the slide rails:

a. Make sure the top flange of a slide rail aligns with the middle of the narrower metal area

between holes in a rack post, as shown in Figure 4.

b. Eac

h rack post requires six screws to attach the slide rail. Mark only the uppermost and

lowermost holes.

c. Mark the square holes at the same height on the other three rack posts.

Figure 4 Determining the cage nut installation holes by using a slide rail

(1) Middle of the narrower metal area between holes

3. Install six cage nuts in the square holes in each rack post, as shown in Figure 5.

Figure 5 Installing a cage nut

4. Align the installation holes on the front end of a slide rail with the cage nuts on a front rack post,

and use six screws to attach the slide rail to the front rack post. Figure 6 us

es the right slide rail as

an example.

Figure 6 Attaching the right slide rail to the front right rack post

5. Keep the slide rail horizontal and adjust its length until the installation holes on the rear end of the

slide rail touch the cage nuts on the rear rack post. Then use screws to attach the slide rail to the

rear rack post.

6. Repeat steps 4 and 5 to install the other slide rail. Make sure the two slide rails are at the same

height so that the switch can be placed on them horizontally.

Installing cage nuts

1. Determine and mark the cage nut installation holes on the front rack posts ,as shown in Figure 7.

Figure 7 Cage nut installation holes

(1) Ca

e nuts

Figure 8 Marking the cage nut installation holes

2. Install the cage nuts.

Installing mounting brackets and cable management brackets

Installing the cable management brackets on the S7506E-V

The S7506E-V has two cable management brackets: the one with a tray is installed at the lower part of

the switch, and the one without a tray is installed at the upper part of the switch. They are installed in the

same way.

To install a cable management bracket:

1. Unpack the cable management brackets.

2. Attach the cable management bracket to the chassis, and align the screws with the screw holes in

the chassis, as shown in Figure 9.

3. Fasten the s

crews.

Figure 9 Installing cable management brackets on an S7506E-V

Installing the cable management brackets on other models

For the models except the S7506E-V, install the cable management bracket on the left mounting bracket,

as shown in Figure 10. T

he switch is supplied with two mounting brackets, and the one with the cable

management bracket screw holes is the left mounting bracket.

Figure 10 Attaching the cable management bracket to the left mounting bracket

Installing the mounting brackets

Before installing the switch in the rack, install the mounting brackets to the chassis, as shown in Figure 11.

• S7506E-V—Facing the front of the switch, mount the left and right mounting brackets to the two

sides of the switch.

• Other models—Facing the front of the switch, mount the mounting bracket with a cable

management bracket to the left of the switch, and mount the mounting bracket without a cable

management bracket to the right of the switch (where the fan tray is located).

Figure 11 Installing the mounting brackets

Installing the switch in the rack

Follow these guidelines when you install the switch in the rack:

• To avoid equipment damage or bodily injury, use a minimum of two people to lift the switch. H3C

recommends that you use a mechanical lift to move the switch.

• Do not hold the filler panels, filler panel handles, or the air vents of chassis to carry the chassis. Any

attempt to carry the switch with these parts might cause equipment damage or even bodily injury.

• After placing the switch on the slide rails, do not leave go of your hands immediately because this

might tip the switch. Tipping the switch can cause switch damage and even bodily injury.

Figure 12 Installing the switch in the rack

Grounding the switch

CAUTION:

Connect the

roundin

cable to the

roundin

system in the equipment room. Do not connect it to a fire

main or lightning rod.

Use the provided grounding cable (yellow-green grounding cable).

Figure 13 Grounding the switch

Installing FRUs

Installing a card

IMPORTANT:

• Before installing a card in the chassis, make sure the connectors on the card are not broken or blocked.

• To ensure good ventilation, install a blank filler panel in an empty slot.

Figure 14 Installing a card

Installing a power module

CAUTION:

• Provide a circuit breaker for each power module and make sure the circuit breaker is off before

installation.

• Do not install power modules of different models on the same switch.

• For dual-grid input, the input voltage and frequency for the two grids must be the same.

• To avoid power module damage or bodily injury, support the bottom of a power module instead of

holding its handle to move the power module.

• To ensure good ventilation, install a blank filler panel over an empty slot.

After you push the power module into the slot, press the power module handle inward until it is secured

in place, and then fasten the captive screws on the power module.

Figure 15 Installing a power module

Connecting power cords

Connecting the PSR320-A/PSR650-A power cord

Figure 16 Connecting the PSR320-A/PSR650-A power cord

Connecting the PSR650C-12A power cord

Figure 17 Connecting the PSR650C-12A power cord

Connecting the PSR1400-A power cord

Figure 18 Connecting the PSR1400-A power cord

Connecting the PSR2800-ACV power cord

The PSR2800-ACV is a built-in power module with AC input and DC output. It provides one system power

socket and one PoE power socket. The methods for connecting the system power cord and PoE power

cord are similar to connecting the PSR1400-A power cord. For more information, see "Connecting the

R1400-A power cord."

Connecting the PSR6000-ACV power cord

The PSR6000-ACV is a built-in power module with AC input and DC output. It provides one system power

socket and three PoE power sockets. Connecting the system power cord is the same as connecting the

PoE power cord. The following illustrates how to connect the system power cord.

To attach the power cord retainer suite:

1. Fasten the retainer suite to the plug of the power cord, making sure you can align the screw holes

in the retainer suite with the screw holes in the power module.

If you cannot align the screw holes in the retainer suite with the screw holes in the power module,

pull the cable retainer suite outwards, rotate it by 180 degrees, and push it in until it is secured in

place.

2. Use a Phillips screwdriver to fasten the two parts of the retainer suite together.

Figure 19 Attaching the power cord retainer suite

(1) Screw holes for connecting the retainer suite to the power module (2) Power cord plug

(3) Screw holes for connectin

the two

parts of the retainer suite

3. Insert the power cord into the power socket on the power module, and fasten the power cord

retainer suite to the power module.

Figure 20 Connecting the AC power cord to the PSR6000-ACV

Connecting the PSR320-D/PSR650-D/PSR650C-12D power cord

Figure 21 Connecting the PSR320-D/PSR650-D/PSR650C-12D power cord

Connecting the PSR1400-D/PSR1400-12D1 power cord

Figure 22 Connecting the PSR1400-D/PSR1400-12D1 power cord

Page is loading ...

H3C S7506E-S Installation, Quick Start

Brand: H3C

Model: S7506E-S

Type: Installation, Quick Start

This manual is also suitable for

Download PDF

report

H3C S7506E-S Installation, Quick Start

This manual is also suitable for

H3C S7506E-S Installation, Quick Start

Related papers

Other documents