Directed DS4+ Installation guide

Directed
Brand
Directed
Model
DS4+
Type
Installation guide
GM9
INSTALLATION GUIDE
This product is intended for installation by a professional installer only! Attempts to install this
product by a person other than a trained professional may result in severe damage to a vehicle’s
electrical system and components.
2017-08-25
© 2017 Directed, Vista CA
DS4+
Designed by Installers for Installers
Contents
Warning! Safety first ....................................................................................................................... 3
Introduction .................................................................................................................................... 4
Pre-installation and application warnings ..................................................................................... 4
Vehicle application guide ........................................................................................................... 5
Wiring connections ......................................................................................................................... 6
Main harness (H1), 12-pin black connector .................................................................................. 6
Relay harness (H2), 10-pin white connector .................................................................................. 6
Data harness (H3), 8-pin white connector ..................................................................................... 6
Analog input/output harness (H4), 22-pin white connector ............................................................. 7
RF Port harness (H5), 2-pin white connector .................................................................................. 7
D2D harness (H6), 4-pin white (1) and black (2) connectors ........................................................... 7
Temperature sensor harness (H7), 2-pin black connector ................................................................ 7
Installation (wiring diagrams, fuse selection & vehicle wiring reference charts) ........................................ 8
Type 1 ..................................................................................................................................... 8
Type 2 ................................................................................................................................... 12
Type 3 ................................................................................................................................... 15
Key2GO ...................................................................................................................................... 17
Configuring the system................................................................................................................... 17
Important! .............................................................................................................................. 17
Vehicles equipped with a manual transmission ............................................................................ 17
RF Systems ............................................................................................................................. 17
8504D Combo Sensor ............................................................................................................. 17
When used in conjunction with SmartStart .................................................................................. 18
D2D port configuration ............................................................................................................ 18
Module programming .............................................................................................................. 19
Keyport location ...................................................................................................................... 20
LED diagnostics and troubleshooting .......................................................................................... 21
Soft reset ................................................................................................................................ 23
Hard reset .............................................................................................................................. 23
Learning the Tach (not needed with Virtual Tach) ............................................................................... 24
Initializing Virtual Tach (not needed with hardwired or data tach applications) ..................................... 24
Limited lifetime consumer warranty .................................................................................................. 25
Quick Reference Guide .................................................................................................................. 26
3
DS4+ GM9
© 2017-08-25 Directed. All rights reserved.
Warning! Safety first
The following safety warnings must be observed at all times:
• Due to the complexity of this system, installation of this product must only be performed by an authorized Directed dealer.
• When properly installed, this system can start the vehicle via a command signal from the remote control. Therefore, never
operate the system in an area that does not have adequate ventilation.
The following precautions are the sole responsibility of the user; however, authorized Directed dealers should:
• Never use a test light or logic probe when installing this unit. Always use a multimeter.
• Never operate the system in an enclosed or partially enclosed area without ventilation (such as a garage).
• When parking in an enclosed or partially enclosed area or when having the vehicle serviced, the remote start system must
be disabled using the installed toggle switch. It is the user’s sole responsibility to properly handle and keep out of reach from
children all remote controls to assure that the system does not unintentionally remote start the vehicle.
• USER MUST INSTALL A CARBON MONOXIDE DETECTOR IN OR ABOUT THE LIVING AREA ADJACENT TO THE VEHICLE.
ALL DOORS LEADING FROM ADJACENT LIVING AREAS TO THE ENCLOSED OR PARTIALLY ENCLOSED VEHICLE
STORAGE AREA MUST REMAIN CLOSED AT ALL TIMES.
Use of this product in a manner contrary to its intended mode of operation may result in property damage, personal injury, or
death. Except when performing the Safety Check outlined in this installation guide, (1) Never remotely start the vehicle with
the vehicle in gear, and (2) Never remotely start the vehicle with the keys in the ignition. The user is responsible for having the
neutral safety feature of the vehicle periodically checked, wherein the vehicle must not remotely start while the car is in gear.
This testing should be performed by an authorized Directed dealer in accordance with the Safety Check outlined in this product
installation guide. If the vehicle starts in gear, cease remote start operation immediately and consult with the user to fix the problem
immediately.
OPERATION OF THE REMOTE START MODULE IF THE VEHICLE STARTS IN GEAR IS CONTRARY TO ITS INTENDED MODE OF
OPERATION. OPERATING THE REMOTE START SYSTEM UNDER THESE CONDITIONS MAY RESULT IN PROPERTY DAMAGE
OR PERSONAL INJURY. IMMEDIATELY CEASE THE USE OF THE UNIT AND REPAIR OR DISCONNECT THE INSTALLED REMOTE
START MODULE. DIRECTED WILL NOT BE HELD RESPONSIBLE OR PAY FOR INSTALLATION OR REINSTALLATION COSTS.
Remote starters for manual transmission pose significant risks if not properly installed and operated. When testing to ensure the
installation is working properly, only remote start the vehicle in neutral gear, on a flat surface and with a functional, fully engaged
parking brake. Do not allow anyone to stand in front of or behind the vehicle.
This product should not be installed in any convertible vehicles, soft or hard top with a manual transmission. Installation in such
vehicles may pose certain risk.
4
DS4+ GM9
© 2017-08-25 Directed. All rights reserved.
Introduction
The GM9 firmware for DS4+ is compatible with specific Buick, Cadillac, Chevrolet and GMC vehicles.
It is a complete solution for remote start, security (when security features are enabled), bypass, and features
built in Bluetooth 4.0 allowing you to configure and control your system. This guide provides information
on the installation of the module as an analog unit, however a digital solution could be available for your
vehicle. Please refer to the DirectLink application or www.directechs.com for more information about which
configuration is best for your application.
Warning! This module is designed to be configured using the DirectLink application for mobile devices, however it can also
be configured using the web tool located at www.directechs.com. To download the DirectLink mobile application, please visit the
Google Play or Apple store.
Pre-installation and application warnings
Firmware notes: This section highlights important information for this specific firmware and will assist in
pricing accordingly, as well as bringing awareness to any operational or vehicle limitations.
T-Harness
compatible
Keys required for
programming
1
Keys required for
operation
0
Compatible with GM9 2.06+
Key2GO is mandatory to control the immobilizer override in this firmware.
Unless specified otherwise, all connectors are displayed from the wire side, with the exception of the OBDII diagnostic
connector.
It is important to check that the fuses are positioned correctly in the module. Refer to the "Fuse selection" section following
each installation type for more information.
Refer to the "Vehicle wiring reference chart" following each installation type.
General notes: This section highlights important information for this specific firmware.
[1] The installation of an aftermarket hood pin is ONLY required on vehicles that are NOT equipped with a factory hood pin.
[2] The siren is ONLY required when enabling the security features during module flashing.
[3] Required ONLY for manual transmission vehicles.
Additional parts required (maximum required):
Diode 6A
0 x 1A Diodes
86 85
30
87a
87
0 x Relay
Resistor 100Ω
1 x 180Ω Resistor
Fuse 7.5A
0 x Fuse
5
DS4+ GM9
© 2017-08-25 Directed. All rights reserved.
Vehicle application guide
The following table lists the vehicles and features which are compatible with this product. The number assigned to each year
allows you to determine which installation type should be used for your vehicle.
Vehicles
2017
2016
2015
2014
2013
2012
2011
2010
PK-Immobilizer Bypass-Data No Key Req'd
DL-Arm Factory Security
DL-Disarm Factory Security
DL-Door Lock Control
DL-Door Unlock
DL-Driver Priority Unlock
DL-Trunk / Hatch Release
Key2GO
RS-3x LOCK START (Start control using OEM Remote)
RS-3x LOCK STOP (Stop control using OEM Remote)
RS-Accessory Activation
RS-Ignition Activation
RS-RAP Shut Down (Retained ACC Power)
RS-SmartStart
RS-Start (Crank) Activation
RS-Tach / RPM Output
SS-Entry Monitoring ALL Door Pins
SS-Entry Monitoring Hood Pin
SS-Entry Monitoring Trunk/Hatch Pin
SS-Factory Alarm Trigger Monitoring
ST-Brake Status (foot brake)
ST-E-Brake Status
ST-Ignition Status
Buick
LaCrosse (Smart Key) 1 1 1 1 1 1 1
• • • • • • • • • • • • • • • • • • • • • • •
Regal (Smart Key) 1 1 1 1 1 1 1
• • • • • • • • • • • • • • • • • • • • • • •
Verano (Smart Key) 1 1 1 1 1 1
• • • • • • • • • • • • • • • • • • • • • • •
Cadillac
ATS (Smart Key) 2 2 2 2
• • • • • • • • • • • • • • • • • • • • • • •
CTS Sedan (Smart Key) 2 2 2
• • • • • • • • • • • • • • • • • • • • • • •
Escalade (Smart Key) 2 2 2
• • • • • • • • • • • • • • • • • • • • • • •
SRX (Smart Key) 1 1 1 1 1 1 1
• • • • • • • • • • • • • • • • • • • • • • •
XTS (Smart Key) 1 1 1 1
• • • • • • • • • • • • • • • • • • • • • • •
Chevrolet
Cruze (Smart Key) 1 1 1 1 1 1
• • • • • • • • • • • • • • • • • • • • • • •
Impala (Smart Key) 1 1 1 1
• • • • • • • • • • • • • • • • • • • • • • •
Malibu (Smart Key) 3 3 1 1 1
• • • • • • • • • • • • • • • • • • • • • • •
Suburban (Smart Key) 2 2 2
• • • • • • • • • • • • • • • • • • • • • • •
Tahoe (Smart Key) 2 2 2
• • • • • • • • • • • • • • • • • • • • • • •
GMC
Yukon (Smart Key) 2 2 2
• • • • • • • • • • • • • • • • • • • • • • •
Legend:
DL: OE Door Lock & Alarm Controls
FOB: Sync CAN Interface w/ FOB Remote
PK: Transponder & Immobilizer Override
RS: Remote Start & Engine Controls
SS: Integrated Security & Monitoring
ST: Function/Feature Status
6
DS4+ GM9
© 2017-08-25 Directed. All rights reserved.
Wiring connections
The wiring connections listed below are specific to this firmware.
Main harness (H1), 12-pin black connector
Conn./Pin Color Description
H1/1 Blue/White Relay 1 N.C. – Immo. Data Interrupt (vehicle side)
1
H1/2 Blue/Red Relay 1 N.O. – No Connection
1
H1/3 Blue Relay 1 COM – Immo. Data Interrupt (connector side)
1
H1/4 White/Brown Relay 3 N.C. – No Connection
1
H1/5 White Relay 3 COM – No Connection
1
H1/6 Red (+) 12 Volt (Battery)
H1/7 Lt. Green/Red Relay 2 N.O. – (-) Ground
1
H1/8 Lt. Green Relay 2 COM – (-) Clutch Output
1
H1/9 Lt. Green/White Relay 2 N.C. – No Connection
1
H1/10 Black (-) Ground
H1/11 White Relay 3 COM – No Connection
1
H1/12 Red (+) 12 Volt (Battery)
Relay harness (H2), 10-pin white connector
Conn./Pin Color Description
H2/1
N/A No Connection
H2/2
Red/Black No Connection
H2/3
Pink/Black No Connection
1
H2/4
Pink/White No Connection
1
H2/5
Red No Connection
H2/6
Green No Connection
1
H2/7
Violet No Connection
H2/8 Orange No Connection
1
H2/9
Red/White No Connection
H2/10
Pink No Connection
Data harness (H3), 8-pin white connector
Conn./Pin Color Description
H3/1 Tan HS CAN Low
H3/2 Tan/Black HS CAN High
H3/3 Orange/Brown No Connection
H3/4 Orange/Green No Connection
H3/5 Lt. Green Single Wire CAN
H3/6 Violet/Brown (MUX) Brake Activation Output
H3/7 Orange/Black No Connection
H3/8 Yellow/Black Immo.Data (connector side)
1. If these outputs are not used by the firmware, they can be configured by the installer when the module is flashed.
7
DS4+ GM9
© 2017-08-25 Directed. All rights reserved.
Analog input/output harness (H4), 22-pin white connector
Conn./Pin Color Description
H4/1 Lt. Green/Black (-) Parking Light Output
1
H4/2 Blue/White (-) Ground When Running (Status) Output
1
H4/3 Dk. Green/Black (-) Lock Output
1
H4/4 Red/White (-) Trunk Output
1
H4/5 Brown/Black (-) Horn Output
1
H4/6 Brown/White N/A
H4/7 White (+) AUX 1 Output
1
H4/8 Violet/Black (+) AUX 4 Output
1
H4/9 Dk. Blue/Black (-) Unlock Output
1
H4/10 Lt. Blue/Black (-) FAD Output
1
H4/11 Brown/Red (+) Siren Output
1
H4/12 Pink (+) Ignition Sense Input
H4/13 Violet (+) Door Sense Input
2
H4/14 Brown (+) Brake Input
2
H4/15 White/Blue (-) Activation Input
2
H4/16 Blue/Red (-) Valet Switch
2
H4/17 Black/White (-) E-Brake Input
2
H4/18 Orange/Black (-) Instant Alarm Trigger Input
2
H4/19 Blue (-) Trunk Sense Input
2
H4/20 Green (-) Door Sense Input
2
H4/21 Gray (-) Hood Pin Input
2
H4/22 Violet/White (AC) Tach Input
RF Port harness (H5), 2-pin white connector
Conn./Pin Color Description
H5/1 N/A RF Loop
H5/2 N/A RF Loop
D2D harness (H6), 4-pin white (1) and black (2) connectors
Conn./Pin Color Description
H6/1 Blue (Data) TX
H6/2 Black (-) Ground
H6/3 Green (Data) RX
H6/4 Red (+) 12 Volt
Temperature sensor harness (H7), 2-pin black connector
Conn./Pin Color Description
H7/1 Black Temperature Sensor
H7/2 Black Temperature Sensor
1. If these outputs are not used by the firmware, they can be configured by the installer when the module is flashed. Note that they are low current and a relay
may be necessary.
2. These connections are only required if the corresponding statuses are not supported by the firmware. See "Vehicle application guide" on page 5 for a
list of compatible features. If these outputs are not used by the firmware, they can be configured by the installer when the module is flashed. Note that they
are low current and a relay may be necessary.
8
DS4+ GM9
© 2017-08-25 Directed. All rights reserved.
Installation (wiring diagrams, fuse selection & vehicle wiring reference charts)
Type 1
Refer to "Pre-installation and application warnings" on page 4 for important information, such as the description of each special note referenced in the diagram ( ).
22 810 12
4 2442
DS4+
DS4
Slide
to open
Proper Fuse
Positioning
DS4+ DS4
It is important to check that the
fuses are positioned correctly.
MAIN (5A) (+)
(-) RLY3 PK LIGHT (15A) (+)
(-) ACC & START (30A) (+)
(-) FLEX RLY (20A) (+)
IGN (20A) (+)
MAIN (5A) (+)
(-) RLY3/PK LIGHT(15A) (+)
5
5
30
20
20
Immo. Data Interrupt (vehicle side.): Blue/White: 1
Immo. Data Interrupt (conn. side): Blue: 3
(-) Ground: Lt. Green/Red: 7
(-) Clutch Output: Lt. Green: 8
(-) Ground: Black: 10
HS CAN Low: Tan : 1
(-) Parking Light Output: Lt. Green/Black: 1
HS CAN High: Tan/Black: 2
Immo.Data (conn.side): Yellow/Black: 8
(MUX) Brake Activation Output: Violet/Brown: 6
SW CAN: Lt.Green: 5
Siren
Hood Pin
(+) 12V Input: Red: 6 & 12
(-) Hood Input: Gray: 21
(+) Siren Output: Brown/Red: 11
Cut
White
at BCM
22
21 23 24 25 26
15 17 18 19 20
8 10 11 13 1412
765
4321
(-) Parking Lights: Pin 22
1
8 9
10 11 12 13 14
17
23
15
21
16
22
18
24
1920
25
2 3 4 5 6 7
Green at BCM
Immo. Data: Green/Violet
or Lt.Blue, pin 2
9
16
242322
17
7
431
65
8
9 10 11 12 13 14 15
16
18 19 20 21
25 26 27
2
HS CAN High: Pin 24
Brake: Pin 7
(+)12V: Pin 4
HS CAN Low: Pin 23
Single Wire CAN:
Pin 22
Lt. Blue at BCM
BCM (under driver-side dash or
in center console passenger side)
Gray
Brown
Black
Pink
Green Lt. Blue
White
Clutch: Pin B
180Ω
A B C
Clutch Switch
(black 3-pin
connector)
Wiring diagram
9
DS4+ GM9
© 2017-08-25 Directed. All rights reserved.
Vehicle wiring reference chart
This section provides vehicle wiring information to guide you through the various stages of your installation. Refer to
www.directechs.com for additional information.
Wire Information Connector Information
Function Color Pin Polarity Location Color Pins Ref.
Buick LaCrosse (Smart key) 2010
Immo. Data Lt. Blue 2 Data BCM under drivers dash. Green 25 A
Parking Lights Lt. Blue 22 (-) BCM under drivers dash. White 26 B
SW CAN Dk. Green 22 Data BCM under drivers dash. Blue 27 C
HS CAN High Tan/Black 24 Data BCM under drivers dash. Blue 27 C
HS CAN Low Tan 23 Data BCM under drivers dash. Blue 27 C
Brake Yellow 7 MUX BCM under drivers dash. Blue 27 C
12V Red/White 4 (+) BCM under drivers dash. Blue 27 C
Buick LaCrosse (Smart key) 2011-2012
Immo. Data Green/Violet 2 Data BCM under drivers dash. Green 25 A
Parking Lights Lt. Green 22 (-) BCM under drivers dash. White 26 B
SW CAN Lt. Green 22 Data BCM under drivers dash. Blue 27 C
HS CAN High Dk. Blue 24 Data BCM under drivers dash. Blue 27 C
HS CAN Low White 23 Data BCM under drivers dash. Blue 27 C
Brake Dk. Blue 7 MUX BCM under drivers dash. Blue 27 C
12V Red/Violet 4 (+) BCM under drivers dash. Blue 27 C
Buick LaCrosse (Smart key) 2013-2016
Immo. Data Green/Violet 2 Data BCM under drivers dash. Green 25 A
Parking Lights
Green/Brown
or Lt. Green
22 (-) BCM under drivers dash. White 26 B
SW CAN Lt. Green 22 Data BCM under drivers dash. Blue 27 C
HS CAN High Dk. Blue 24 Data BCM under drivers dash. Blue 27 C
HS CAN Low
Dk. Blue/
Yellow
23 Data BCM under drivers dash. Blue 27 C
Brake Yellow 7 MUX BCM under drivers dash. Blue 27 C
12V Red/Violet 4 (+) BCM under drivers dash. Blue 27 C
10
DS4+ GM9
© 2017-08-25 Directed. All rights reserved.
Wire Information Connector Information
Function Color Pin Polarity Location Color Pins Ref.
Buick Regal (Smart Key) 2012-2014
Immo. Data Green/Violet 2 Data BCM under drivers dash. Green 25 A
Parking Lights Green/Gray 22 (-) BCM under drivers dash. White 26 B
SW CAN Green 22 Data BCM under drivers dash. Blue 27 C
HS CAN High Blue 24 Data BCM under drivers dash. Blue 27 C
HS CAN Low White 23 Data BCM under drivers dash. Blue 27 C
Brake Blue/Yellow 7 MUX BCM under drivers dash. Blue 27 C
12V
Red/White or
Red/Brown
4 (+) BCM under drivers dash. Blue 27 C
Clutch Output [3] Yellow B MUX Clutch switch. Black 3 D
Buick Verano (Smart Key) 2012-2016
Immo. Data Green/Violet 2 Data BCM passenger side center console. Green 25 E
Parking Lights Green/Gray 22 (-) BCM passenger side center console. White 26 F
SW CAN Green 22 Data BCM passenger side center console. Blue 27 G
HS CAN High Blue 24 Data BCM passenger side center console. Blue 27 G
HS CAN Low White 23 Data BCM passenger side center console. Blue 27 G
Brake Blue/Yellow 7 MUX BCM passenger side center console. Blue 27 G
12V Red/Brown 4 (+) BCM passenger side center console. Blue 27 G
Clutch Output [3] Yellow B MUX Clutch switch. Black 3 D
Cadillac SRX (Smart Key) 2010-2012
Immo. Data Green/Violet 2 Data BCM under drivers dash. Green 25 A
Parking Lights
Green/Brown
or Lt. Green
22 (-) BCM under drivers dash. White 26 B
SW CAN Lt. Green 22 Data BCM under drivers dash. Blue 27 C
HS CAN High Dk. Blue 24 Data BCM under drivers dash. Blue 27 C
HS CAN Low
Dk. Blue/
Yellow
23 Data BCM under drivers dash. Blue 27 C
Brake Yellow 7 MUX BCM under drivers dash. Blue 27 C
12V Red/Violet 4 (+) BCM under drivers dash. Blue 27 C
Cadillac SRX (Smart Key) 2013-2016
Immo. Data
Lt. Green/
Violet
2 Data BCM under drivers dash. Green 25 A
Parking Lights
Lt. Green/
Gray
22 (-) BCM under drivers dash. White 26
B
SW CAN Green 22 Data BCM under drivers dash. Blue 27 C
HS CAN High Tan/Black 24 Data BCM under drivers dash. Blue 27 C
HS CAN Low Tan 23 Data BCM under drivers dash. Blue 27 C
Brake Blue/Yellow 7 MUX BCM under drivers dash. Blue 27 C
12V Red/Violet 4 (+) BCM under drivers dash. Blue 27 C
Cadillac XTS (Smart Key) 2013-2016
Immo. Data
Lt. Green/
Violet
2 Data BCM under drivers dash. Green 25 A
Parking Lights
Lt. Green/
Gray
22 (-) BCM under drivers dash. White 26
B
SW CAN Lt. Green 22 Data BCM under drivers dash. Blue 27 C
HS CAN High Lt. Blue 24 Data BCM under drivers dash. Blue 27
C
HS CAN Low White 23 Data BCM under drivers dash. Blue 27 C
Brake Blue/Yellow 7 MUX BCM under drivers dash. Blue 27 C
12V Red/Violet 4 (+) BCM under drivers dash. Blue 27 C
11
DS4+ GM9
© 2017-08-25 Directed. All rights reserved.
Wire Information Connector Information
Function Color Pin Polarity Location Color Pins Ref.
Chevrolet Cruze (Smart Key) 2012-2016
Immo. Data Green/Violet 2 Data BCM passenger side center console. Green 25 E
Parking Lights Green/Gray 22 (-) BCM passenger side center console. White 26 F
SW CAN Green 22 Data BCM passenger side center console. Blue 27 G
HS CAN High Blue 24 Data BCM passenger side center console. Blue 27 G
HS CAN Low White 23 Data BCM passenger side center console. Blue 27 G
Brake Blue/Yellow 7 MUX BCM passenger side center console. Blue 27 G
12V Red/Gray 4 (+) BCM passenger side center console. Blue 27 G
Clutch Output [3] Yellow B MUX Clutch switch. Black 4 D
Chevrolet Impala (Smart Key) 2014-2016
Immo. Data Green/Violet 2 Data BCM under drivers dash. Green 25 A
Parking Lights Green/Gray 22 (-) BCM under drivers dash. White 26 B
SW CAN Lt. Green 22 Data BCM under drivers dash. Blue 27 C
HS CAN High Blue 24 Data BCM under drivers dash. Blue 27 C
HS CAN Low White 23 Data BCM under drivers dash. Blue 27 C
Brake Blue/Yellow 7 MUX BCM under drivers dash. Blue 27 C
12V Red/Violet 4 (+) BCM under drivers dash. Blue 27 C
Chevrolet Malibu (Smart Key) 2013-2015
Immo. Data Green/Violet 2 Data BCM under drivers dash. Green 25 A
Parking Lights Gray 22 (-) BCM under drivers dash. White 26 B
SW CAN Green 22 Data BCM under drivers dash. Blue 27 C
HS CAN High Blue 24 Data BCM under drivers dash. Blue 27 C
HS CAN Low White 23 Data BCM under drivers dash. Blue 27 C
Brake Blue 7 MUX BCM under drivers dash. Blue 27 C
12V Red/Violet 4 (+) BCM under drivers dash. Blue 27 C
12
DS4+ GM9
© 2017-08-25 Directed. All rights reserved.
Type 2
Refer to "Pre-installation and application warnings on page 4 for important information, such as the description of each special note referenced in the diagram ( ).
22 810 12
4 2442
DS4+
DS4
Slide
to open
Proper Fuse
Positioning
DS4+ DS4
It is important to check that the
fuses are positioned correctly.
MAIN (5A) (+)
(-) RLY3 PK LIGHT (15A) (+)
(-) ACC & START (30A) (+)
(-) FLEX RLY (20A) (+)
IGN (20A) (+)
MAIN (5A) (+)
(-) RLY3/PK LIGHT(15A) (+)
5
5
30
20
20
Siren
Hood Pin
(-) Hood Input: Gray: 21
(+) Siren Output: Brown/Red: 11
1
8 9
10 11
17
23
15
21
16
22
2 3 4
Green
at BCM
White
at BCM
Gray
at BCM
22
21 23 24 25 26
15 17 18 19 20
8 10 11 13 1412
765
4321
Lt. Blue
at BCM
242322
17
7
431
65
8
9 10 11 12 13 14 15
16 18 19 20 21
25 26 27
2
(-) Parking Lights: Gray or
Green/Gray, pin 22
HS CAN High: Blue, pin 25
Brake: Pin 7
Single Wire
CAN: Green, pin 23
HS CAN Low: White, pin 24
Immo. Data:
Green/Violet,
pin 2
9
16
12 13 14
18
24
1920
25
5 6 7
1 2 3
4 5 6 7 8 9
10 11 12 13 14 15 16
17 18 19 20 21
22
24
25
26
23
Immo. Data Interrupt (vehicle side): Blue/White: 1
Immo. Data Interrupt (conn. side): Blue: 3
(-) Ground: Black: 10
HS CAN Low: Tan : 1
(-) Parking Light Output: Lt. Green/Black: 1
HS CAN High: Tan/Black: 2
Immo.Data (conn.side): Yellow/Black: 8
(MUX) Brake Activation Output: Violet/Brown: 6
SW CAN: Lt.Green: 5
(+) 12V Input: Red: 6 & 12
CUT
BCM (under driver-side dash or
behind glovebox)
Gray
Brown
Black
Pink
Green Lt. Blue
White
(+)12V:
Red/Gray or
Red/Violet, pin 4
(-) Ground: Lt. Green/Red: 7
(-) Clutch Output: Lt. Green: 8
Clutch: Pin B
180Ω
A B C
Clutch Switch
(black 3-pin
connector)
Wiring diagram
13
DS4+ GM9
© 2017-08-25 Directed. All rights reserved.
Vehicle wiring reference chart
This section provides vehicle wiring information to guide you through the various stages of your installation. Refer to
www.directechs.com for additional information.
Wire Information Connector Information
Function Color Pin Polarity Location Color Pins Ref.
Cadillac ATS (Smart Key) 2013-2015
Immo. Data Green/Violet 2 Data BCM behind glove box. Green 25 A
Parking Lights
Gray or
Green/Gray
22 (-) BCM behind glove box. White 26 B
HS CAN High Blue 25 Data BCM behind glove box. White 26 B
HS CAN Low White 24 Data BCM behind glove box. White 26 B
SW CAN Green 23 Data BCM behind glove box. Gray 26 C
Brake Blue/Yellow 7 MUX BCM behind glove box. Blue 27 D
12V Red/Gray 4 (+) BCM behind glove box. Blue 27 D
Clutch Output [3] Yellow B MUX Clutch switch. Black 3 E
Cadillac CTS (Smart Key) 2013-2015
Immo. Data Green/Violet 2 Data BCM under driver dash. Green 25 F
Parking Lights
"Gray or
Green/Gray"
22 (-) BCM under driver dash. White 26 G
HS CAN High Blue 25 Data BCM under driver dash. White 26 G
HS CAN Low White 24 Data BCM under driver dash. White 26 G
SW CAN Green 23 Data BCM under driver dash. Gray 26 H
Brake Blue/Yellow 7 MUX BCM under driver dash. Blue 27 I
12V Red/Gray 4 (+) BCM under driver dash. Blue 27 I
Chevrolet Suburban (Smart Key) 2015
Immo. Data Green/Violet 2 Data BCM under driver dash. Green 25 F
Parking Lights Green/Gray 22 (-) BCM under driver dash. White 26 G
HS CAN High Blue 25 Data BCM under driver dash. White 26 G
HS CAN Low White 24 Data BCM under driver dash. White 26 G
SW CAN Green 23 Data BCM under driver dash. Gray 26 H
Brake White/Green 7 MUX BCM under driver dash. Blue 27
I
12V Red/Violet 4 (+) BCM under driver dash. Blue 27
I
14
DS4+ GM9
© 2017-08-25 Directed. All rights reserved.
Wire Information Connector Information
Function Color Pin Polarity Location Color Pins Ref.
Chevrolet Tahoe (Smart Key) 2015-2016
Immo. Data Green/Violet 2 Data BCM under driver dash. Green 25
F
Parking Lights Green/Gray 22 (-) BCM under driver dash. White 26 G
HS CAN High Blue 25 Data BCM under driver dash. White 26
G
HS CAN Low White 24 Data BCM under driver dash. White 26
G
SW CAN Green 23 Data BCM under driver dash. Gray 26
H
Brake White/Green 7 MUX BCM under driver dash. Blue 27
I
12V Red/Violet 4 (+) BCM under driver dash. Blue 27
I
Cadillac Escalade (Smart Key) 2015-2016
Immo. Data Green/Violet 2 Data BCM under driver dash. Green 25
F
Parking Lights Green/Gray 22 (-) BCM under driver dash. White
26 G
HS CAN High Blue 25 Data BCM under driver dash. White
26 G
HS CAN Low White 24 Data BCM under driver dash. White
26 G
SW CAN Green 23 Data BCM under driver dash. Gray
26 H
Brake White/Green 7 MUX BCM under driver dash. Blue
27 I
12V Red/Violet 4 (+) BCM under driver dash. Blue
27 I
GMC Yukon (Smart Key) 2015-2016
Immo. Data Green/Violet 2 Data BCM under driver dash. Green
25 F
Parking Lights Green/Gray 22 (-) BCM under driver dash. White
26 G
HS CAN High Blue 25 Data BCM under driver dash. White
26 G
HS CAN Low White 24 Data BCM under driver dash. White
26 G
SW CAN Green 23 Data BCM under driver dash. Gray
26 H
Brake White/Green 7 MUX BCM under driver dash. Blue
27 I
12V Red/Violet 4 (+) BCM under driver dash. Blue
27 I
15
DS4+ GM9
© 2017-08-25 Directed. All rights reserved.
Type 3
Refer to "Pre-installation and application warnings on page 4 for important information, such as the description of each special note referenced in the diagram ( ).
DS4+
DS4
Slide
to open
Proper Fuse
Positioning
DS4+ DS4
It is important to check that the
fuses are positioned correctly.
MAIN (5A) (+)
(-) RLY3 PK LIGHT (15A) (+)
(-) ACC & START (30A) (+)
(-) FLEX RLY (20A) (+)
IGN (20A) (+)
MAIN (5A) (+)
(-) RLY3/PK LIGHT(15A) (+)
5
5
30
20
20
Immo. Data Interrupt (vehicle side): Blue/White: 1
Immo. Data Interrupt (conn.side): Blue: 3
(-) Ground: Black: 10
HS CAN Low: Tan : 1
(-) Parking Light Output: Lt. Green/Black: 1
HS CAN High: Tan/Black: 2
Immo.Data (conn. side): Yellow/Black: 8
(MUX) Brake Activation Output: Violet/Brown: 6
SW CAN: Lt.Green: 5
Siren
Hood Pin
(+) 12V Input: Red: 6 & 12
(-) Hood Input: Gray: 21
(+) Siren Output: Brown/Red: 11
Cut
White
at BCM
22
21 23 24 25 26
15 17 18 19 20
8 10 11 13 1412
765
4321
(-) Parking Lights: Gray, pin 22
1
8 9
10 11 12 13 14
17
23
15
21
16
22
18
24
1920
25
2 3 4 5 6 7
Green at BCM
Immo. Data:
Green/Violet, pin 2
9
16
242322
17
7
431
65
8
9 10 11 12 13 14 15
16 18 19 20 21
25 26 27
2
HS CAN High:
Blue, pin 25
Brake: Pin 7
(+)12V: Red/Brown, pin 4
HS CAN Low: White, pin 24
SW CAN:
Green, pin 22
Lt. Blue at BCM
BCM (center console passenger side)
Gray
Brown
Black
Pink
Green Lt. Blue
White
Wiring diagram
16
DS4+ GM9
© 2017-08-25 Directed. All rights reserved.
Vehicle wiring reference chart
This section provides vehicle wiring information to guide you through the various stages of your installation. Refer to
www.directechs.com for additional information.
Wire Information Connector Information
Function Color Pin Polarity Location Color Pins Ref.
Chevrolet Malibu (Smart Key) 2016
Immo. Data Green/Violet 2 Data BCM passenger side center console. Green 25 A
Parking Lights Gray 22 (-) BCM passenger side center console. White 26 B
HS CAN High Blue 25 Data BCM passenger side center console. White 26 B
HS CAN Low White 24 Data BCM passenger side center console. White 26 B
SW CAN Green 22 Data BCM passenger side center console. Blue 27 C
Brake Blue/Yellow 7 MUX BCM passenger side center console. Blue 27 C
12V Red/Brown 4 (+) BCM passenger side center console. Blue 27 C
17
DS4+ GM9
© 2017-08-25 Directed. All rights reserved.
Key2GO
This feature is mandatory to control the immobilizer override in this firmware.
Key2GO has been designed and developed to bypass the advanced encryption layers found in modern vehicles. It uses an array
of servers to generate a duplicate of the original key, allowing the installation of a remote starter without having to give up a key.
The advantage is that this feature allows you to use one original key and the server to configure the bypass in the vehicle.
All Key2GO-compatible firmware are clearly indicated in the function list of each vehicle search result page and will also appear
on the flash page. Any first-time user must re-register to gain access to Key2GO, and some additional information will be required
to complete the registration process, such as your Directed account number and store name.
Key2GO is compatible with XKLoader2 and the online web tool, as well as XKLoader3 and the Directechs Mobile application.
Refer to "Module programming" on page 19 of this guide for instructions on how to program features using Key2GO.
Configuring the system
Important!
Once the DS4+ module is installed in the vehicle following the instructions in "Warning! Safety first" on page 3, launch the
DirectLink application on your mobile device, and select Configure DS4/DS4+. Follow the on-screen instructions to configure the
system.
Note: Your system can also be configured using XKLoader2 on www.directechs.com.
Vehicles equipped with a manual transmission
Additional connections may be required if these functions are not supported by the firmware.
Connection Description
(-) E-Brake Status Input
(Black/White, pin 17)
Must be connected to a working emergency brake in the vehicle. Although most vehicles have simple
(-) trigger emergency brake circuits note some vehicles do not and may require unique integration
methodologies.
(-) Door Trigger Input
(Green, pin 20) OR
(+) Door Input (Violet, pin
13)
Must be connected to a working door trigger in the vehicle, which monitors all doors. The unit must monitor
the door pins to allow the Ready Mode process to be enabled.
Note: Some vehicles may require unique integration methodologies for this circuit. For more information, refer
to www.directechs.com.
(AC) Tachometer Input
(Violet/White, pin 22)
Must be connected to a working tachometer signal in the vehicle (fuel injector, ignition coil, true tach, etc.)
and learned successfully to the DS4+.
RF Systems
An RF System consists of one or multiple remotes, a Control Center (antenna), and an antenna cable – various combinations exist.
An RF System allows the vehicle owner to control the system with enhanced range. Two-way models are available. Please follow
the instructions included with the kit for appropriate installation and programming information.
8504D Combo Sensor
The 8504D Combo Sensor must be paired to the device before it can be used. To enter pairing, turn the vehicle ignition to the
ON position, then press and hold the programming button on the Control Center (antenna) until the LED starts flashing. Once
pairing mode has been entered, your Combo Sensor is ready to use.
Your Combo Sensor is preset for the majority of applications, however it can be adjusted using the DirectLink application, as well
18
DS4+ GM9
© 2017-08-25 Directed. All rights reserved.
as a compatible LED or LCD remote. Please refer to the instructions included with your sensor for more information on how to make
adjustments.
When used in conjunction with SmartStart
To enable D2D communication between the DS4+ and the SmartStart one of the following actions must be executed:
• SmartStart with Loops – The brown loop must be cut.
• SmartStart with Pigtails – The gray wire must be connected to a ground source.
Loops Pigtails
DO NOT connect the SmartStart 2-pin power harness when using the DS4+. Power and ground will be provided by the D2D
connector on main module. Refer to the SmartStart documentation for further details.
D2D port configuration
The system will automatically configure the D2D ports based on your selections in the module programming. The white D2D port is
reserved for SmartStart. To ensure proper functionality with SmartStart, it is important that it is selected in the system programming
of the DirectLink application or via the online web tool.
Note: Both black D2D ports are reserved for the Control Center (antenna) and 8504D Combo Sensor.
19
DS4+ GM9
© 2017-08-25 Directed. All rights reserved.
Module programming
Refer to "Keyport location" on page 20 for more information and for troubleshooting purposes.
To connect the module:
1
Please ensure that the vehicle is in a safe location and cannot move forward during
programming. For vehicles equipped with a manual transmission, make sure the gearshift
lever is in the neutral position.
2
Connect all the harnesses to the DS4+, EXCEPT the 12-pin main power harness.
Connect all but the
12-pin harness
3
Connect the 12-pin main power harness, and wait until the LED turns ON solid red.
Must be
connected LAST
&
Solid
4
Remove battery from one key fob and make sure that the other key fob is located more than
10 feet away from vehicle.
5
Put the key fob (with battery removed) in the keyport (Refer to "Keyport location" on page
20).
6
Press once and then press and hold the Push-to-Start button until the ignition
turns ON then release. The LED flashes green.
&&
Flashes
Green
7
Leave ignition ON until the LED starts flashing orange slowly.
Flashes
Orange
Slowly
8
Press the Push-to-Start button once to turn the ignition OFF. The LED continues to flash orange
slowly.
Flashes
Orange
Slowly
&
9
Remove the module from the vehicle and reconnect it to your computer. The Directechs web site will automatically
recognize that you are moving on to the second phase of the programming sequence.
10
Select the method and click on Submit Key2GO Request.
11
Once the configuration is completed, reconnect the module. The LED turns ON solid green
for 3 seconds, then turns OFF.
Solid x 3 secs Off
&
12
Pair remotes (if applicable). For information on how to pair a specific remote, please
refer to its corresponding owner documentation, which can be found inside the product
packaging of the complete system or on www.directechs.com.*
Pair
remotes*
13
By default, the tachometer is preprogrammed for the vehicle. For instructions on how to
program tach, see page 24.
Initialize
tachometer
* Your aftermarket remote may differ from the model shown in the illustrations.
You have successfully completed the module programming sequence.
20
DS4+ GM9
© 2017-08-25 Directed. All rights reserved.
Keyport location
Vehicle Keyport location Reference
Buick LaCrosse 2014 - 2016 Place the transmitter in the transmitter pocket inside the armrest storage area. A
Buick LaCrosse 2010 - 2013 Remove the cupholder from the center console storage area. Place transmitter
in the pocket with the buttons facing up.
B
Buick Regal 2011 - 2014 Remove the cupholder liner from the center console cupholder. Place
transmitter in the pocket with the buttons facing up.
C
Buick Verano 2012 - 2016 Remove the cupholder liner from the center console cupholder. Place
transmitter in the pocket with the buttons facing up.
D
Cadillac ATS 2013 - 2016 Open the center console storage area and the storage tray. Place the
transmitter in the transmitter pocket.
E
Cadillac CTS Sedan 2014 - 2016 Open the center console storage area and remove the rubber mat. Place the
transmitter in the transmitter pocket.
A
Cadillac Escalade 2015-2016 Open the center console storage area and the storage tray. Place the
transmitter in the transmitter pocket.
A
Cadillac SRX 2010 - 2016 Open the center console storage area and the storage tray. Place the
transmitter in the transmitter pocket.
A
Cadillac XTS 2013 - 2016 Open the center console storage area and the storage tray. Place the
transmitter in the transmitter pocket.
A
Chevrolet Cruze 2012 - 2016 Remove the plastic trim piece from the small storage area next to the
accessory power outlet toward the front of the console. Push the button on the
transmitter to extend the blade, insert the key blade into the transmitter slot.
F
Chevrolet Impala 2014-2016 Open the center console and place the transmitter in the transmitter pocket
with the buttons facing the front of the vehicle.
A or B
Chevrolet Malibu 2013-2016 Open the center console and place the transmitter in the transmitter pocket
with the buttons facing the front of the vehicle.
A or B
Chevrolet Suburban 2015 Open the center console and place the transmitter in the transmitter pocket
with the buttons facing the front of the vehicle.
A
Chevrolet Tahoe 2015-2016 Open the center console and place the transmitter in the transmitter pocket
with the buttons facing the front of the vehicle.
A
GMC Yukon 2015-2016 Open the center console and place the transmitter in the transmitter pocket
with the buttons facing the front of the vehicle.
A
Center Console
Cupholder
B
C
D
E
I
A
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25
  • Page 26 26
  • Page 27 27

Directed DS4+ Installation guide

Directed
Brand
Directed
Model
DS4+
Type
Installation guide
Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents