Directed DS4+ Installation guide

Brand: Directed

Model: DS4+

Category: Car alarm

Type: Installation guide

MA3

INSTALLATION GUIDE

This product is intended for installation by a professional installer only! Attempts to install this

product by a person other than a trained professional may result in severe damage to a vehicle’s

electrical system and components.

2017- 02-15

DS4+

Contents

Warning! Safety first ....................................................................................................................... 3

Introduction .................................................................................................................................... 4

Pre-installation and application warnings ..................................................................................... 4

Vehicle application guide ........................................................................................................... 5

Wiring connections ......................................................................................................................... 6

Main harness (H1), 12-pin black connector .................................................................................. 6

Relay harness (H2), 10-pin white connector .................................................................................. 6

Data harness (H3), 8-pin white connector ..................................................................................... 6

Analog input/output harness (H4), 22-pin white connector ............................................................. 7

RF Port harness (H5), 2-pin white connector .................................................................................. 7

D2D harness (H6), 4-pin white (1) and black (2) connectors ........................................................... 7

Temperature sensor harness (H7), 2-pin black connector ................................................................ 7

Installation (wiring diagrams, fuse selection & vehicle wiring reference charts) ........................................ 8

Type 1 - with THMAN1 T-Harness ................................................................................................ 8

Type 1 - without T-Harness .......................................................................................................... 9

Type 2 - with THMAN1 T-Harness .............................................................................................. 11

Type 2 - without T-Harness ........................................................................................................ 12

Type 3 - with THMAN1 T-Harness .............................................................................................. 14

Type 3 - without T-Harness ........................................................................................................ 15

Type 4 - with THMAN1 T-Harness .............................................................................................. 17

Type 4 - without T-Harness ........................................................................................................ 18

Type 5 ................................................................................................................................... 20

Accessing the parking light circuit ............................................................................................ 23

Immobilizer interface .............................................................................................................. 24

Connecting the module .................................................................................................................. 25

Important! .............................................................................................................................. 25

Adjusting the 8504D Shock Sensor ........................................................................................... 25

When used in conjunction with SmartStart .................................................................................. 26

D2D 1.0/2.0 port configuration ............................................................................................... 26

Module programming .............................................................................................................. 27

LED diagnostics and troubleshooting .......................................................................................... 28

Soft reset ................................................................................................................................ 30

Hard reset .............................................................................................................................. 30

Learning the Tach (not needed with Virtual Tach) ............................................................................... 31

Initializing Virtual Tach (not needed with hardwired or data tach applications) ..................................... 31

Limited lifetime consumer warranty .................................................................................................. 32

Quick Reference Guide .................................................................................................................. 33

DS4+ MA3

Warning! Safety ﬁrst

The following safety warnings must be observed at all times:

• Due to the complexity of this system, installation of this product must only be performed by an authorized Directed dealer.

• When properly installed, this system can start the vehicle via a command signal from the remote control. Therefore, never

operate the system in an area that does not have adequate ventilation.

The following precautions are the sole responsibility of the user; however, authorized Directed dealers should:

• Never use a test light or logic probe when installing this unit. Always use a multimeter.

• Never operate the system in an enclosed or partially enclosed area without ventilation (such as a garage).

• When parking in an enclosed or partially enclosed area or when having the vehicle serviced, the remote start system must

be disabled using the installed toggle switch. It is the user’s sole responsibility to properly handle and keep out of reach from

children all remote controls to assure that the system does not unintentionally remote start the vehicle.

• USER MUST INSTALL A CARBON MONOXIDE DETECTOR IN OR ABOUT THE LIVING AREA ADJACENT TO THE VEHICLE.

ALL DOORS LEADING FROM ADJACENT LIVING AREAS TO THE ENCLOSED OR PARTIALLY ENCLOSED VEHICLE

STORAGE AREA MUST REMAIN CLOSED AT ALL TIMES.

Use of this product in a manner contrary to its intended mode of operation may result in property damage, personal injury, or

death. Except when performing the Safety Check outlined in this installation guide, (1) Never remotely start the vehicle with

the vehicle in gear, and (2) Never remotely start the vehicle with the keys in the ignition. The user is responsible for having the

neutral safety feature of the vehicle periodically checked, wherein the vehicle must not remotely start while the car is in gear.

This testing should be performed by an authorized Directed dealer in accordance with the Safety Check outlined in this product

installation guide. If the vehicle starts in gear, cease remote start operation immediately and consult with the user to ﬁx the problem

immediately.

OPERATION OF THE REMOTE START MODULE IF THE VEHICLE STARTS IN GEAR IS CONTRARY TO ITS INTENDED MODE OF

OPERATION. OPERATING THE REMOTE START SYSTEM UNDER THESE CONDITIONS MAY RESULT IN PROPERTY DAMAGE

OR PERSONAL INJURY. IMMEDIATELY CEASE THE USE OF THE UNIT AND REPAIR OR DISCONNECT THE INSTALLED REMOTE

START MODULE. DIRECTED WILL NOT BE HELD RESPONSIBLE OR PAY FOR INSTALLATION OR REINSTALLATION COSTS.

Remote starters for manual transmission pose signiﬁcant risks if not properly installed and operated. When testing to ensure the

installation is working properly, only remote start the vehicle in neutral gear, on a ﬂat surface and with a functional, fully engaged

parking brake. Do not allow anyone to stand in front of or behind the vehicle.

This product should not be installed in any convertible vehicles, soft or hard top with a manual transmission. Installation in such

vehicles may pose certain risk.

DS4+ MA3

Introduction

The MA3 ﬁrmware for DS4+ is a complete solution for remote start, security (if applicable), bypass interface,

and convenience needs compatible with speciﬁc Mazda, Scion and Toyota vehicles.

Warning! This module can only be programmed via the web tool, which can be found on

www.directechs.com or using the Directechs Mobile application for smartphones. Features and functions will

become accessible when you connect the module using the XKLoader.

Pre-installation and application warnings

Firmware notes: This section highlights important information for this speciﬁc ﬁrmware and will assist in

pricing accordingly, as well as bringing awareness to any operational or vehicle limitations.

T-Harness

compatible

THMAN1

Keys required for

programming

Keys required for

operation

see note

 The optional Plug & Play THMAN1 T-Harness is sold separately.

 When using the THMAN1 T-Harness, the OEM remote functionality is retained during remote start runtime.

 All connectors are displayed from the wire side (unless speciﬁed otherwise).

 It is important to check that the fuses are positioned correctly in the module. Refer to the "Fuse selection" section following

each installation type for more information.

 Refer to the "Vehicle wiring reference chart" following each installation type.

 No takeover feature is available. The vehicle will shut down as soon as a door is opened.

 To remote start the engine, the hood, hatch, and all doors must be closed.

 When installing this solution in one of the vehicles from this guide, the vehicle's OEM alarm will no longer be functional. The

installation of a hybrid system (remote starter and alarm combo) is highly recommended to preserve vehicle security.

 It is normal for the key symbol to ﬂash during remote start runtime.

 Parking lights for Mazda 3 can also be found in drivers kick. Please refer to www.directechs.com for additional information.

General notes: This section highlights important information for this speciﬁc ﬁrmware.

[1] The installation of an aftermarket hood pin is ONLY required on vehicles that are NOT equipped with an OEM hood pin.

[2] The siren is ONLY required when enabling the security features during module ﬂashing.

[3] Only required to retain OEM remote functionality during remote start runtime if not using the THMAN1 T-Harness.

[4] See page 23 for more information about accessing the parking wiring. Parking lights for Mazda 3 can also be found in

drivers kick. Please refer to www.directechs.com for additional information.

[5] Type 5 vehicles ONLY: 1 (one) key is required for operation. For key wrap instructions, refer to page 24.

[6] Only required when installing a hybrid system.

Additional parts required (maximum required):

Diode 6A

0 x 1A Diodes

86 85

87a

2 x Relay

Resistor 100Ω

0 x Resistor

Fuse 7.5A

1 x Fuse

DS4+ MA3

Vehicle application guide

The following table lists the vehicles and features which are compatible with this product. The number assigned to each year

allows you to determine which installation type should be used for your vehicle.

Vehicles

2016

2015

2014

2013

PK-Immobilizer Bypass-

Data No Key Req'd

DL-Door Lock Control

DL-Door Unlock

DL-Driver Priority Unlock

DL-Trunk / Hatch Release

FOB-Control of

aftermarket alarm with

RS-3x LOCK START (Start

control using OEM

RS-3x LOCK STOP (Stop

control using OEM

RS-SmartStart

RS-Tach / RPM Output

SS-Entry Monitoring ALL

Door Pins

SS-Entry Monitoring Hood

SS-Entry Monitoring

Trunk/Hatch Pin

ST-Brake Status (foot

brake)

ST-E-Brake Status

ST-Ignition Status

Mazda

3 (Smart Key) 3 3 3

••••••••••••••••

6 (Smart Key) 2 2 2

••••••••••••••••

CX-3 (Smart Key) 4

••••••••••••••••

CX-5 (Smart Key) 1111

••••••••••••••••

Scion

iA (Smart Key)

[5]

5 •••••••••••••••

Toyota

Yaris Sedan (Smart Key)

[5]

5 •••••••••••••••

Legend:

PK: Transponder & Immobilizer Override

DL: OE Door Lock & Alarm Controls

FOB: Sync CAN Interface w/ FOB Remote

RS: Remote Start & Engine Controls

SS: Integrated Security & Monitoring

ST: Function/Feature Status

DS4+ MA3

Wiring connections

The wiring connections listed below are speciﬁc to this ﬁrmware.

Main harness (H1), 12-pin black connector

Conn./Pin Color Description

H1/1 Blue/White Relay 1 N.C. – Parking Lights Interrupt (vehicle side)

H1/2 Blue/Red Relay 1 N.O.

H1/3 Blue Relay 1 COM – Parking Lights Interrupt (conn. side)

H1/4 White/Brown Relay 3 N.C. – (+) Starter Output

H1/5 White Relay 3 COM – (+) Starter Output

H1/6 Red (+) 12 Volt (Battery)

H1/7 Lt. Green/Red Relay 2 N.O. – (+) Ignition Output

H1/8 Lt. Green Relay 2 COM – (+) 12V Ignition Input

H1/9 Lt. Green/White Relay 2 N.C. – No Connection

H1/10 Black (-) Ground

H1/11 White Relay 3 COM – (+) Starter Output

H1/12 Red (+) 12 Volt (Battery)

Relay harness (H2), 10-pin white connector

Conn./Pin Color Description

H2/1

N/A No Connection

H2/2

Red/Black No Connection

H2/3

Pink/Black No Connection

H2/4

Pink/White No Connection

H2/5

Red No Connection

H2/6

Green No Connection

H2/7

Violet No Connection

H2/8 Orange No Connection

H2/9

Red/White No Connection

H2/10

Pink No Connection

Data harness (H3), 8-pin white connector

Conn./Pin Color Description

H3/1 Tan HS CAN Low

H3/2 Tan/Black HS CAN High

H3/3 Orange/Brown No Connection

H3/4 Orange/Green No Connection

H3/5 Lt. Green No Connection

H3/6 Violet/Brown (MUX) Door Lock Output

H3/7 Orange/Black No Connectiont

H3/8 Yellow/Black No Connection

1. If these outputs are not used by the ﬁrmware, they can be conﬁgured by the installer when the module is ﬂashed.

DS4+ MA3

Analog input/output harness (H4), 22-pin white connector

Conn./Pin Color Description

H4/1 Lt. Green/Black (-) Parking Lights Output

H4/2 Blue/White (-) Key Wrap Output

H4/3 Dk. Green/Black No Connection

H4/4 Red/White (-) Trunk Release Output

H4/5 Brown/Black No Connection

H4/6 Brown/White N/A

H4/7 White (+) Accessory 1 Output

H4/8 Violet/Black (+) Accessory 2 Output

H4/9 Dk. Blue/Black (-) Ignition Interrupt Output

H4/10 Lt. Blue/Black (-) Push-to-Start Output

H4/11 Brown/Red (+) Siren Output

H4/12 Pink (+) Ignition Sense Input

H4/13 Violet (+) Door Sense Input

H4/14 Brown (+) Brake Input

H4/15 White/Blue (-) Activation Input

H4/16 Red/Blue (-) Valet Switch

H4/17 Black/White (-) E-Brake Input

H4/18 Orange/Black (-) Trunk Shunt Input

H4/19 Blue (-) Trunk Sense Input

H4/20 Green (-) Door Sense Input

H4/21 Gray (-) Hood Pin Input

H4/22 Violet/White (AC) Tach Input

RF Port harness (H5), 2-pin white connector

Conn./Pin Color Description

H5/1 N/A RF Loop

H5/2 N/A RF Loop

D2D harness (H6), 4-pin white (1) and black (2) connectors

Conn./Pin Color Description

H6/1 Blue (Data) TX

H6/2 Black (-) Ground

H6/3 Green (Data) RX

H6/4 Red (+) 12 Volt

Temperature sensor harness (H7), 2-pin black connector

Conn./Pin Color Description

H7/1 Black Temperature Sensor

H7/2 Black Temperature Sensor

1. If these outputs are not used by the ﬁrmware, they can be conﬁgured by the installer when the module is ﬂashed. Note that they are low current and a relay

may be necessary.

2. These connections are only required if the corresponding statuses are not supported by the ﬁrmware. See "Vehicle application guide" on page 5 for a

list of compatible features. If these outputs are not used by the ﬁrmware, they can be conﬁgured by the installer when the module is ﬂashed. Note that they

are low current and a relay may be necessary.

DS4+ MA3

Installation (wiring diagrams, fuse selection & vehicle wiring reference charts)

Type 1 - with THMAN1 T-Harness

Refer to "Pre-installation and application warnings" on page 4 and "Vehicle wiring reference chart" on page 10 for important information on this installation.

Cut

DS4+

DS4

22 810 12

4 2442

It is important to check that the

fuses are positioned correctly. See

Fuse selection on the next page for

more information.

Parking Light Interrupt (vehicle side): Blue/White

Parking Light Interrupt (conn. side): Blue

(-) Trunk Release Output: Red/White

Hood Pin

(-) Hood Input: Gray

Siren

(+) Siren Output: Brown/Red

(MUX) Door Lock: Violet/Brown

Trunk Release Switch

(White conn. in driver dash)

(-) Trunk Release:

White/Blue,

pin 3

1 2 3

Factory Alarm/

Door Lock:

White/Green

Driver Kick Panel

Parking Light

Switch Assembly

(-) Parking Lights:

Yellow, pin 3

Parking Lights

Interrupt:

Green, pin 4

(-) Parking Lights Output: Lt.Green/Black

Start/Stop Unit

(White conn. at steering column)

Start/Stop Unit

(White conn. at steering column)

THMAN1

(optional T-Harness)

T-Harness

Relays

(+) Trunk Shunt Input: Orange/Black

Trunk Release Actuator

(Blue conn. in left rear quarter panel)

(+) Trunk Release Actuator:

Green, pin 2

2 3

1112 18

109

86 7

1615

DS4+ MA3

Type 1 - without T-Harness

Refer to "Pre-installation and application warnings" on page 4 and "Vehicle wiring reference chart" on page 10 for important information on this installation.

Optional

Cut

DS4+

DS4

22 810 12

4 2442

It is important to check that the

fuses are positioned correctly. See

Fuse selection on the next page for

more information.

Parking Light Interrupt (vehicle side): Blue/White: 1

Parking Light Interrupt (conn. side): Blue: 3

(+) 12V: Lt. Green: 8

(-) Ground: Black: 10

(+) Starter Output: White: 5 & 11

(+) 12V: Red: 6 & 12

(-) Trunk Release Output: Red/White: 4

(-) Parking Lights Output: Lt.Green/Black: 1

(-) Ignition Interrupt Output: Blue/Black: 9

(-) Push-to-Start Output: Lt. Blue/Black: 10

(+) Accessory 2 Output: Violet/Black: 8

(+) Accessory 1 Output: White: 7

Hood Pin

(+) Ignition Output: Lt.Green/Red: 7

(-) Hood Input: Gray: 21

Siren

(+) Siren Output: Brown/Red: 11

HS CAN Low: Tan : 1

HS CAN High: Tan/Black: 2

Start/Stop Unit

(White conn. at steering column)

Start/Stop Unit

(White conn. at

steering column)

(-) PTS: Green/White

or Lt.Green/Red, pin 20

Fuse Box

(White conn.

at drivers kick)

(+) 12V:

White, pin 1

86 8587

87a

86 85

87a

(+)12V

32 31 30 29 28 27 26 25 24 23 22 21 20 19 18

12456789101112131415 3

Trunk Release Switch

(White conn. in driver dash)

(-) Trunk Release:

White/Blue,

pin 3

1 2 3

1314151617

192021

2223

12 123

910

(+) Starter:

Brown/Black,

pin 23

(+) Ignition:

Lt. Green/Red,

pin 10

HS CAN Low: Red/Yellow, pin 8

HS CAN High: White/Black, pin 7

(+) Accessory 1: Yellow/Green, pin 2

(+) Accessory 2: Brown/Red, pin 14

Parking Light

Switch Assembly

(-) Parking Lights:

Yellow, pin 3

Parking Lights Interrupt:

Green, pin 4

(+) Ign. 2 Interrupt: Gray/Red, pin 3

(+) Ign. 3 Interrupt:

Violet, pin 17

(+) Trunk Shunt Input: Orange/Black: 18

Trunk Release Actuator

(Blue conn. at left rear quarter panel)

(+) Trunk Release Actuator: Green, pin 2

2 3

1112 18

109

86 7

1615

(MUX) Door Lock Output: Violet/Brown: 6

Factory Alarm/

Door Lock:

White/Green

Driver Kick Panel

DS4+ MA3

Fuse selection

To ensure correct functionality of your system, please conﬁgure the fuses on your system as follows:

DS4+ DS4

22 810

4 2442

Slide to open

MAIN (5A) (+)

(-) RLY3 PK LIGHT (15A) (+)

(-) ACC & START (30A) (+)

(-) FLEX RLY (20A) (+)

IGN (20A) (+)

MAIN (5A) (+)

(-) RLY3 PK LIGHT (15A) (+)

(-) ACC & START (30A) (+)

(-) FLEX RLY (20A) (+)

IGN (20A) (+)

MAIN (5A) (+)

(-) RLY3 PK LIGHT (15A) (+)

(-) ACC & START (30A) (+)

(-) FLEX RLY (20A) (+)

IGN (20A) (+)

MAIN (5A) (+)

(-) RLY3 PK LIGHT (15A) (+)

(-) ACC & START (30A) (+)

(-) FLEX RLY (20A) (+)

IGN (20A) (+)

MAIN (5A) (+)

(-) RLY3 PK LIGHT (15A) (+)

(-) ACC & START (30A) (+)

(-) FLEX RLY (20A) (+)

IGN (20A) (+)

MAIN (5A) (+)

(-) RLY3 PK LIGHT (15A) (+)

(-) ACC & START (30A) (+)

(-) FLEX RLY (20A) (+)

IGN (20A) (+)

22 8

4 2442

Slide to open

MAIN (5A) (+)

(-) RLY3/PK LIGHT(15A) (+)

MAIN (5A) (+)

(-) RLY3/PK LIGHT(15A) (+)

Vehicle wiring reference chart

This section provides vehicle wiring information to guide you through the various stages of your installation. Refer to

www.directechs.com for additional information.

Wire Information Connector Information

Function Color Pin Polarity Location Color Pins Ref.

Mazda CX-5 (Smart Key) 2013-2016

HS CAN High White/Black 7 Data Start/Stop unit in steering column. White 24 A

HS CAN Low Red/Yellow 8 Data Start/Stop unit in steering column. White 24 A

Accessory 1 Yellow/Green 2 (+) Start/Stop unit in steering column. White 24 A

Accessory 2 Brown/Red 14 (+) Start/Stop unit in steering column. White 24 A

Ignition 1 Lt. Green/Red 10 (+) Start/Stop unit in steering column. White 24 A

Starter Brown/Black 23 (+) Start/Stop unit in steering column. White 24 A

PTS 1 Green/White or Lt. Green/Red 20 (-) Start/Stop unit in steering column. White 32 B

Ignition 2 Interrupt [3] Gray/Red 3 Cut Start/Stop unit in steering column. White 32 B

Ignition 3 Interrupt [3] Violet 17 Cut Start/Stop unit in steering column. White 32 B

Door Lock White/Green 12 MUX Driver kick, door harness. White 32 C

12V White 1 (+) Fusebox in driver kick. White 1 D

Trunk Release Actuator [6] Green 2 (+) BCM in left rear quarter panel. Blue 18 -

Trunk Release White/Blue 3 (-) Trunk release switch. White 3 -

Parking Lights Yellow 3 (-) Parking light assembly switch. White 6 E

Parking Lights Interrupt Green 4 Cut Parking light assembly switch. White 6 E

DS4+ MA3

Type 2 - with THMAN1 T-Harness

Refer to "Pre-installation and application warnings" on page 4 and "Vehicle wiring reference chart" on page 13 for important information on this installation.

Cut

DS4+

DS4

22 810 12

4 2442

It is important to check that the

fuses are positioned correctly. See

Fuse selection on the next page for

more information.

Parking Light Interrupt (vehicle side): Blue/White

Parking Light Interrupt (conn. side): Blue

(-) Trunk Release Output: Red/White

Hood Pin

(-) Hood Input: Gray

(+) Trunk Shunt Input: Orange/Black

Siren

(+) Siren Output: Brown/Red

Parking Light

Switch Assembly

(-) Parking Lights:

Yellow, pin 3

Parking Lights

Interrupt:

Green, pin 4

(-) Parking Lights Output: Lt.Green/Black

Trunk Release Actuator conn.

(Blue conn. at left rear quarter panel)

(+) Trunk Release Actuator:

Green or Brown, pin 2

2 3

1112 18

109

86 7

1615

(-) Trunk Release:

Green/Red, pin 1

1 2 3

THMAN1

(optional T-Harness)

T-Harness

Relays

(MUX) Door Lock Output: Violet/Brown

Factory Alarm/

Door Lock:

White/Green

Start/Stop Unit

(White conn. at steering column)

Start/Stop Unit

(White conn. at steering column)

Driver Kick Panel

Trunk Release Switch

(White conn. in driver dash)

DS4+ MA3

Type 2 - without T-Harness

Refer to "Pre-installation and application warnings" on page 4 and "Vehicle wiring reference chart" on page 13 for important information on this installation.

Optional

Cut(+) Ign. 2 Interrupt: Gray/Red, pin 3

(+) Ign. 3 Interrupt:

Violet, pin 17

DS4+

DS4

22 810 12

4 2442

It is important to check that the

fuses are positioned correctly. See

Fuse selection on the next page for

more information.

Parking Light Interrupt (vehicle side): Blue/White: 1

Parking Light Interrupt (conn. side): Blue: 3

(+)12V: Lt. Green: 8

(-) Ground: Black: 10

(+) Starter Output: White: 5 & 11

(+) 12V: Red: 6 & 12

(+) Ignition Output: Lt. Green/Red: 7

HS CAN Low: Tan : 1

HS CAN High: Tan/Black: 2

(-) PTS: Green/White

or Lt. Green/Red, pin 20

(+) 12V: White, pin 1

86 8587

87a

86 85

87a

(+)12V

32 31 30 29 28 27 26 25 24 23 22 21 20 19 18

12456789101112131415 3

(-) Trunk Release:

Green/Red, pin 1

1314151617

192021

2223

12 123

910

(+) Starter:

Brown/Black,

pin 23

(+) Ignition:

Lt. Green/Red,

pin 10

HS CAN Low: Red, pin 8

HS CAN High: White, pin 7

(+) Accessory 1: Yellow/Green, pin 2

(+) Accessory 2: Brown/Red, pin 14

Parking Light

Switch Assembly

Parking Lights Interrupt:

Green, pin 4

(-) Parking Lights:

Yellow, pin 3

(+) Trunk Release Actuator: Green or Brown, pin 2

1 2 3

(-) Trunk Release Output: Red/White: 4

(-) Parking Lights Output: Lt. Green/Black: 1

(-) Ignition Interrupt Output: Blue/Black: 9

(-) Push-to-Start Output: Lt. Blue/Black: 10

(+) Accessory 2 Output: Violet/Black: 8

(+) Accessory 1 Output: White: 7

Hood Pin

(-) Hood Input: Gray: 21

Siren

(+) Siren Output: Brown/Red: 11

(+) Trunk Shunt Input: Orange/Black: 18

Trunk Release Actuator conn.

(Blue conn. at BCM in left rear quarter panel)

2 3

1112 18

109

86 7

1615

(MUX) Door Lock Output: Violet/Brown: 6

Factory Alarm/

Door Lock:

White/Green

Start/Stop Unit

(White conn. at steering column)

Start/Stop Unit

(White conn. at

steering column)

Fuse Box

(White conn.

at drivers kick)

Trunk Release Switch

(White conn. in driver dash)

Driver Kick Panel

DS4+ MA3

Fuse selection

To ensure correct functionality of your system, please conﬁgure the fuses on your system as follows:

DS4+ DS4

22 810

4 2442

Slide to open

MAIN (5A) (+)

(-) RLY3 PK LIGHT (15A) (+)

(-) ACC & START (30A) (+)

(-) FLEX RLY (20A) (+)

IGN (20A) (+)

MAIN (5A) (+)

(-) RLY3 PK LIGHT (15A) (+)

(-) ACC & START (30A) (+)

(-) FLEX RLY (20A) (+)

IGN (20A) (+)

MAIN (5A) (+)

(-) RLY3 PK LIGHT (15A) (+)

(-) ACC & START (30A) (+)

(-) FLEX RLY (20A) (+)

IGN (20A) (+)

MAIN (5A) (+)

(-) RLY3 PK LIGHT (15A) (+)

(-) ACC & START (30A) (+)

(-) FLEX RLY (20A) (+)

IGN (20A) (+)

MAIN (5A) (+)

(-) RLY3 PK LIGHT (15A) (+)

(-) ACC & START (30A) (+)

(-) FLEX RLY (20A) (+)

IGN (20A) (+)

MAIN (5A) (+)

(-) RLY3 PK LIGHT (15A) (+)

(-) ACC & START (30A) (+)

(-) FLEX RLY (20A) (+)

IGN (20A) (+)

22 8

4 2442

Slide to open

MAIN (5A) (+)

(-) RLY3/PK LIGHT(15A) (+)

MAIN (5A) (+)

(-) RLY3/PK LIGHT(15A) (+)

Vehicle wiring reference chart

This section provides vehicle wiring information to guide you through the various stages of your installation. Refer to

www.directechs.com for additional information.

Wire Information Connector Information

Function Color Pin Polarity Location Color Pins Ref.

Mazda 6 (Smart Key) 2014-2016

HS CAN High White 7 Data Start/Stop unit in steering column. White 24 A

HS CAN Low Red 8 Data Start/Stop unit in steering column. White 24 A