Directed DS4+ Installation guide

Type
Installation guide
VW10
INSTALLATION GUIDE
This product is intended for installation by a professional installer only! Attempts to install this
product by a person other than a trained professional may result in severe damage to a vehicle’s
electrical system and components.
2017-11- 02
© 2017 Directed, Vista CA
DS4+
Designed by Installers for Installers
Contents
Warning! Safety first ....................................................................................................................... 3
Introduction .................................................................................................................................... 4
Pre-installation and application warnings ..................................................................................... 4
Vehicle application guide ........................................................................................................... 5
Wiring connections ......................................................................................................................... 6
Main harness (H1), 12-pin black connector .................................................................................. 6
Relay harness (H2), 10-pin white connector .................................................................................. 6
Data harness (H3), 8-pin white connector ..................................................................................... 6
Analog input/output harness (H4), 22-pin white connector ............................................................. 7
RF Port harness (H5), 2-pin white connector .................................................................................. 7
D2D harness (H6), 4-pin white (1) and black (2) connectors ........................................................... 7
Temperature sensor harness (H7), 2-pin black connector ................................................................ 7
Installation (wiring diagrams, fuse selection & vehicle wiring reference charts) ........................................ 8
Type 1 ..................................................................................................................................... 8
Type 2 ................................................................................................................................... 11
Type 3 ................................................................................................................................... 14
Type 4 ................................................................................................................................... 16
Type 5 ................................................................................................................................... 18
Type 6 ................................................................................................................................... 20
Type 7 ................................................................................................................................... 22
Type 8 ................................................................................................................................... 24
Type 9 ................................................................................................................................... 26
Type 10 ................................................................................................................................. 29
Type 11 ................................................................................................................................. 31
Immobilizer interface .................................................................................................................... 33
Method 1: Key Wrap .............................................................................................................. 33
Method 2: Immobilizer interface with 556U (Regular Key) ........................................................... 33
Method 3: Immobilizer interface with OEM Immobilizer Receiver .................................................. 34
Connecting the module .................................................................................................................. 35
Important! .............................................................................................................................. 35
RF Systems ............................................................................................................................. 35
8504D Combo Sensor ............................................................................................................. 35
When used in conjunction with SmartStart .................................................................................. 36
D2D port configuration ............................................................................................................ 36
Module programming .............................................................................................................. 37
LED diagnostics and troubleshooting .......................................................................................... 38
Soft reset ................................................................................................................................ 40
Hard reset .............................................................................................................................. 40
Learning the Tach (not needed with Virtual Tach) ............................................................................... 41
Initializing Virtual Tach (not needed with hardwired or data tach applications) ..................................... 41
Limited lifetime consumer warranty .................................................................................................. 42
Quick Reference Guide .................................................................................................................. 43
3
DS4+ VW10
© 2017-11-02 Directed. All rights reserved.
Warning! Safety first
The following safety warnings must be observed at all times:
Due to the complexity of this system, installation of this product must only be performed by an authorized Directed dealer.
When properly installed, this system can start the vehicle via a command signal from the remote control. Therefore, never
operate the system in an area that does not have adequate ventilation.
The following precautions are the sole responsibility of the user; however, authorized Directed dealers should:
Never use a test light or logic probe when installing this unit. Always use a multimeter.
Never operate the system in an enclosed or partially enclosed area without ventilation (such as a garage).
When parking in an enclosed or partially enclosed area or when having the vehicle serviced, the remote start system must
be disabled using the installed toggle switch. It is the user’s sole responsibility to properly handle and keep out of reach from
children all remote controls to assure that the system does not unintentionally remote start the vehicle.
USER MUST INSTALL A CARBON MONOXIDE DETECTOR IN OR ABOUT THE LIVING AREA ADJACENT TO THE VEHICLE.
ALL DOORS LEADING FROM ADJACENT LIVING AREAS TO THE ENCLOSED OR PARTIALLY ENCLOSED VEHICLE
STORAGE AREA MUST REMAIN CLOSED AT ALL TIMES.
Use of this product in a manner contrary to its intended mode of operation may result in property damage, personal injury, or
death. Except when performing the Safety Check outlined in this installation guide, (1) Never remotely start the vehicle with
the vehicle in gear, and (2) Never remotely start the vehicle with the keys in the ignition. The user is responsible for having the
neutral safety feature of the vehicle periodically checked, wherein the vehicle must not remotely start while the car is in gear.
This testing should be performed by an authorized Directed dealer in accordance with the Safety Check outlined in this product
installation guide. If the vehicle starts in gear, cease remote start operation immediately and consult with the user to fix the problem
immediately.
OPERATION OF THE REMOTE START MODULE IF THE VEHICLE STARTS IN GEAR IS CONTRARY TO ITS INTENDED MODE OF
OPERATION. OPERATING THE REMOTE START SYSTEM UNDER THESE CONDITIONS MAY RESULT IN PROPERTY DAMAGE
OR PERSONAL INJURY. IMMEDIATELY CEASE THE USE OF THE UNIT AND REPAIR OR DISCONNECT THE INSTALLED REMOTE
START MODULE. DIRECTED WILL NOT BE HELD RESPONSIBLE OR PAY FOR INSTALLATION OR REINSTALLATION COSTS.
Remote starters for manual transmission pose significant risks if not properly installed and operated. When testing to ensure the
installation is working properly, only remote start the vehicle in neutral gear, on a flat surface and with a functional, fully engaged
parking brake. Do not allow anyone to stand in front of or behind the vehicle.
This product should not be installed in any convertible vehicles, soft or hard top with a manual transmission. Installation in such
vehicles may pose certain risk.
4
DS4+ VW10
© 2017-11-02 Directed. All rights reserved.
Introduction
The VW10 firmware for DS4+ is compatible with specific Volkswagen and Audi vehicles. It is a complete
solution for remote start, security (when security features are enabled), bypass, and features built in Bluetooth
4.0 allowing you to configure and control your system. This guide provides information on the installation of
the module using VW10. Please refer to the DirectLink application or www.directechs.com for more information
about which configuration is best for your application.
Warning! This module is designed to be configured using the DirectLink application for mobile devices, however it can also
be configured using the web tool located at www.directechs.com. To download the DirectLink mobile application, please visit the
Google Play or Apple store.
Pre-installation and application warnings
Firmware notes: This section highlights important information for this specific firmware and will assist in
pricing accordingly, as well as bringing awareness to any operational or vehicle limitations.
T-Harness
compatible
Keys required for
programming
1
Keys required for
operation
1
Unless specified otherwise, all connectors are displayed from the wire side, with the exception of the OBDII diagnostic
connector.
It is important to check that the fuses are positioned correctly in the module. Refer to the "Fuse selection" section following
each installation type for more information.
Refer to the "Vehicle wiring reference chart" following each installation type.
General notes: This section highlights important information for this specific firmware.
[1] The installation of an aftermarket hood pin is ONLY required on vehicles that are not equipped with a factory hood pin.
[2] The siren is ONLY required when enabling the security features during module flashing.
[3] For Key Wrap instructions, refer to pages 33 & 34.
[4] Locks and trunk release output ONLY required if door locks or trunk are not supported in data.
[5] Diodes and brake connection only required on vehicles where brake needs to be depressed to start.
Additional parts required (maximum required):
Diode 6A
2 x 1A Diodes
86 85
30
87a
87
2 x Relay
Resistor 100
0 x Resistor
Fuse 7.5A
2 x Fuse
5
DS4+ VW10
© 2017-11-02 Directed. All rights reserved.
Vehicle application guide
The following table lists the vehicles and features which are compatible with this product. The number assigned to each year
allows you to determine which installation type should be used for your vehicle.
Vehicles
2017
2016
2015
2014
2013
2012
2011
2010
2009
2008
2007
2006
2004
PK-Universal RF Bypass- Key Req'd
AV-Parking Lights Control
DL-Arm Factory Security
DL-Disarm Factory Security
DL-Door Lock Control
DL-Door Unlock
DL-Driver Priority Unlock
DL-Trunk / Hatch Release
FOB-Control of aftermarket alarm with OEM remote
RS-3x LOCK START (Start control using OEM Remote)
RS-3x LOCK STOP (Stop control using OEM Remote)
RS-Accessory Activation
RS-Ignition Activation
RS-RAP Shut Down (Retained ACC Power)
RS-SmartStart
RS-Start (Crank) Activation
RS-Tach / RPM Output
SS-Entry Monitoring ALL Door Pins
SS-Entry Monitoring Hood Pin
SS-Entry Monitoring Trunk/Hatch Pin
ST-Brake Status (foot brake)
ST-Door Locks Status
ST-E-Brake Status
ST-Ignition Status
Audi
A3
4 4 4 4 4 8 8 8 8
Q3 5 5 5
R8
4 4 4 4 8 8
TT 4 4 4 4 4 4 8 8 8 8
Volkswagen 17 16 15 14 13 12 11 10 09 08 07 06 04
EOS 1 1 1 1 1 9 9 9 9
Golf 2 2 2 2 2 9 9 9 9
GTI 2 2 2 2 2 9 9 9 9
Jetta 11 11 11 3 3 3 3 9 9 9 9 9
Jetta GLI 1 1 1
Jetta SportWagen 1 1 1 1 7 9
Passat 2 2 2 2 2 2 10 10 10 10 10
Passat CC 6 6 6 6 6 6 10 10
Rabbit 9 9 9 9
Tiguan 1 1 1 1 1 1 1
Legend:
AV: Horn and Light Controls
DL: OE Door Lock & Alarm Controls
FOB: Sync CAN Interface w/ FOB Remote
PK: Transponder & Immobilizer Override
RS: Remote Start & Engine Controls
SS: Integrated Security & Monitoring
ST: Function/Feature Status
6
DS4+ VW10
© 2017-11-02 Directed. All rights reserved.
Wiring connections
The wiring connections listed below are specific to this firmware.
Main harness (H1), 12-pin black connector
Conn./Pin Color Description
H1/1 Blue/White Relay 1 N.C. – Parking Light Interrupt (conn. side)
1
H1/2 Blue/Red Relay 1 N.O. – (+) Parking Light Output or (+)12V Input
1
H1/3 Blue Relay 1 COM – (+) Parking Light Interrupt (vehicle side)
1
H1/4 White/Brown Relay 3 N.C. – No Connection
1
H1/5 White Relay 3 COM – (+) Accessory Output
1
H1/6 Red (+) 12 Volt (Input)
H1/7 Lt. Green/Red Relay 2 N.O. – Key Wrap
1
H1/8 Lt. Green Relay 2 COM – Key Wrap
1
H1/9 Lt. Green/White Relay 2 N.C. – Key Wrap
1
H1/10 Black (-) Ground
H1/11 White Relay 3 COM – (+) Accessory Output
1
H1/12 Red (+) 12 Volt (Input)
Relay harness (H2), 10-pin white connector
Conn./Pin Color Description
H2/1
N/A No Connection
H2/2
Red/Black No Connection
H2/3
Pink/Black No Connection
H2/4
Pink/White No Connection
H2/5
Red No Connection
H2/6
Green No Connection
H2/7
Violet No Connection
H2/8 Orange No Connection
H2/9
Red/White No Connection
H2/10
Pink No Connection
Data harness (H3), 8-pin white connector
Conn./Pin Color Description
H3/1 Tan HS CAN Low
H3/2 Tan/Black HS CAN High
H3/3 Orange/Brown FT CAN Low
H3/4 Orange/Green FT CAN High
H3/5 Lt. Green No Connection
H3/6 Violet/Brown (MUX) Lock/Unlock Output
H3/7 Orange/Black ISO BUS 2
H3/8 Yellow/Black ISO BUS 1
1. If these outputs are not used by the firmware, they can be configured by the installer when the module is flashed.
7
DS4+ VW10
© 2017-11-02 Directed. All rights reserved.
Analog input/output harness (H4), 22-pin white connector
Conn./Pin Color Description
H4/1 Lt. Green/Black (-) Hazards Output
1
H4/2 Blue/White (-) Key Release Output
1
H4/3 Dk. Green/Black (-) Lock Output
1
H4/4 Red/White (-) Trunk Release Output
1
H4/5 Brown/Black (-) Horn Output
1
H4/6 Brown/White N/A
H4/7 White (+) Starter Output
1
H4/8 Violet/Black (+) Ignition Output
1
H4/9 Dk. Blue/Black (-) Unlock Output
1
H4/10 Lt. Blue/Black (-) FAD Output
1
H4/11 Brown/Red (+) Siren Output
1
H4/12 Pink (+) Ignition Sense Input
H4/13 Violet (+) Door Sense Input
2
H4/14 Brown (+) Brake Input
2
H4/15 White/Blue (-) Activation Input
2
H4/16 Blue/Red (-) Valet Switch
2
H4/17 Black/White (-) E-Brake Input
2
H4/18 Orange/Black (-) Instant Alarm Trigger Input
2
H4/19 Blue (-) Trunk Sense Input
2
H4/20 Green (-) Door Sense Input
2
H4/21 Gray (-) Hood Pin Input
2
H4/22 Violet/White (AC) Tach Input
RF Port harness (H5), 2-pin white connector
Conn./Pin Color Description
H5/1 N/A RF Loop
H5/2 N/A RF Loop
D2D harness (H6), 4-pin white (1) and black (2) connectors
Conn./Pin Color Description
H6/1 Blue (Data) TX
H6/2 Black (-) Ground
H6/3 Green (Data) RX
H6/4 Red (+) 12 Volt
Temperature sensor harness (H7), 2-pin black connector
Conn./Pin Color Description
H7/1 Black Temperature Sensor
H7/2 Black Temperature Sensor
1. If these outputs are not used by the firmware, they can be configured by the installer when the module is flashed. Note that they are low current and a relay
may be necessary.
2. These connections are only required if the corresponding statuses are not supported by the firmware. See "Vehicle application guide" on page 5 for a
list of compatible features. If these outputs are not used by the firmware, they can be configured by the installer when the module is flashed. Note that they
are low current and a relay may be necessary.
8
DS4+ VW10
© 2017-11-02 Directed. All rights reserved.
Installation (wiring diagrams, fuse selection & vehicle wiring reference charts)
Type 1
Refer to "Pre-installation and application warnings" on page 4 for important information, such as the description of special notes referenced in the diagram ( ).
16
8
9
1
Parking Light Interrupt (conn. side): Blue/White: 1
(+) Parking Light Output: Blue/Red: 2
Parking Light Interrupt (vehicle side): Blue: 3
Key Wrap: Lt. Green: 8
Key Wrap: Lt. Green/White: 9
(-) Ground: Black: 10
HS CAN 1 Low: Tan : 1
(+) Starter / Brake Activation Output: White: 7
(+) Ignition Output: Violet/Black: 8
HS CAN 1 High: Tan/Black: 2
FT CAN High: Orange/Green: 4
FT CAN Low: Orange/Brown: 3
Siren
Hood Pin
(+) 12V Input: Red: 6 & 12
Key Wrap: Lt.Green/Red: 7
(-) Hood Input: Gray: 21
(+) Siren Output: Brown/Red: 11
HS CAN High: Orange/Black, pin 6
HS CAN Low: Orange/Brown, pin 14
(+) Parking Lights: Gray/Yellow, pin 3
1
2
4
5
6
7
9
10
3
8
CUT
6
14
1
8
9
16
12
29
28
42 25 1
52 41 24 11
FT CAN Low: Orange/Brown, pin 3
(+) Ignition:
Black, pin 14
(+) Starter: Red/Black or
Red/Brown,pin 6
FT CAN High: Orange/Green, pin 4
Brown VESCM connector C
(+) Brake: Black/Red, pin 17
Steering column module
(behind steering column trim)
[5] Diode 1A
[5] Diode 1A
Headlight switch
(black conn. at
light switch)
Parking Lights Interrupt:
Red/White or Red/Blue, pin 8
B
C
A
VESCM - Driver side under dashboard
(+) 12V:
Red/Yellow,
pin 42
Diagnostic
Connector
OBDII
22 810 12
4 2442
DS4+
DS4
Slide
to open
Proper Fuse
Positioning
DS4+ DS4
It is important to check that the
fuses are positioned correctly.
MAIN (5A) (+)
(-) RLY3 PK LIGHT (15A) (+)
(-) ACC & START (30A) (+)
(-) FLEX RLY (20A) (+)
IGN (20A) (+)
MAIN (5A) (+)
(-) RLY3/PK LIGHT(15A) (+)
5
5
30
20
20
9
DS4+ VW10
© 2017-11-02 Directed. All rights reserved.
Vehicle wiring reference chart
This section provides vehicle wiring information to guide you through the various stages of your installation. Refer to
www.directechs.com for additional information.
Wire Information Connector Information
Function Color Pin Polarity Location Color Pins Ref.
Volkswagen EOS 2010-2014
Parking Light Gray/Yellow 3 (+) Headlight Switch. Black 10 A
Parking Light Interrupt Red/White 8 Cut Headlight Switch. Black 10 A
Starter Red/Brown or Red/Black 6 (+) Steering column module. Black 16 B
Ignition Black 14 (+) Steering column module. Black 16 B
FT CAN High Orange/Green 4 Data Steering column module. Black 16 B
FT CAN Low Orange/Brown 3 Data Steering column module. Black 16 B
HS CAN High Orange/Black 6 Data OBDII. Violet/Black 16 C
HS CAN Low Orange/Brown 14 Data OBDII. Violet/Black 16 C
12V Red /Yellow 42 (+) VESCM connector C, under drivers dash. Brown 52 D
Brake Black/Red 17 (+) VESCM connector C, under drivers dash. Brown 52 D
Volkswagen Jetta GLI 2012-2014
Parking Light Gray/Yellow 3 (+) Headlight Switch. Black 10 A
Parking Light Interrupt Red/White 8 Cut Headlight Switch. Black 10 A
Starter Red/Brown or Red/Black 6 (+) Steering column module. Black 16 B
Ignition Black 14 (+) Steering column module. Black 16 B
FT CAN High Orange/Green 4 Data Steering column module. Black 16 B
FT CAN Low Orange/Brown 3 Data Steering column module. Black 16 B
HS CAN High Orange/Black 6 Data OBDII. Violet/Black 16 C
HS CAN Low Orange/Brown 14 Data OBDII. Violet/Black 16 C
12V Red /Yellow 42 (+) VESCM connector C, under drivers dash. Brown 52 D
Brake Black/Red 17 (+) VESCM connector C, under drivers dash. Brown 52 D
10
DS4+ VW10
© 2017-11-02 Directed. All rights reserved.
Wire Information Connector Information
Function Color Pin Polarity Location Color Pins Ref.
Volkswagen Jetta SportWagen 2011-2014
Parking Light Gray/Yellow 3 (+) Headlight Switch. Black 10 A
Parking Light Interrupt Red/White 8 Cut Headlight Switch. Black 10 A
Starter Red/Brown or Red/Black 6 (+) Steering column module. Black 16 B
Ignition Black 14 (+) Steering column module. Black 16 B
FT CAN High Orange/Green 4 Data Steering column module. Black 16 B
FT CAN Low Orange/Brown 3 Data Steering column module. Black 16 B
HS CAN High Orange/Black 6 Data OBDII. Violet/Black 16 C
HS CAN Low Orange/Brown 14 Data OBDII. Violet/Black 16 C
12V Red /Yellow 42 (+) VESCM connector C, under drivers dash. Brown 52 D
Brake Black/Red 17 (+) VESCM connector C, under drivers dash. Brown 52 D
Volkswagen Tiguan 2010-2016
Parking Light Gray/Yellow 3 (+) Headlight switch. Black 10 A
Parking Light Interrupt Red/Blue 8 Cut Headlight switch. Black 10 A
Ignition Black 14 (+) Steering column module behind steering column trim. Black 16 B
Starter Red/White or Red/Black 6 (+) Steering column module behind steering column trim. Black 16 B
FT CAN High Orange/Green 4 Data Steering column module behind steering column trim. Black 16 B
FT CAN Low Orange/Brown 3 Data Steering column module behind steering column trim. Black 16 B
HS CAN High Orange/Black 6 Data OBDII. Violet/Black 16 C
HS CAN Low Orange/Brown 14 Data OBDII. Violet/Black 16 C
12V Red/Violet 42 (+) VESCM connector C, under drivers dash. Brown 52 D
Brake Black/Red 17 (+) VESCM connector C, under drivers dash. Brown 52 D
11
DS4+ VW10
© 2017-11-02 Directed. All rights reserved.
Type 2
Refer to "Pre-installation and application warnings" on page 4 for important information, such as the description of special notes referenced in the diagram ( ).
16
8
9
1
Parking Light Interrupt (conn. side): Blue/White: 1
Key Wrap: Lt. Green: 8
Key Wrap: Lt. Green/White: 9
(-) Ground: Black: 10
HS CAN 1 Low: Tan : 1
(+) Starter / Brake Activation Output: White: 7
(+) Ignition Output: Violet/Black: 8
HS CAN 1 High: Tan/Black: 2
FT CAN High: Orange/Green: 4
FT CAN Low: Orange/Brown: 3
Siren
Hood Pin
(+) 12V Input: Red: 6 & 12
Key Wrap: Lt.Green/Red: 7
(-) Hood Input: Gray: 21
(+) Siren Output: Brown/Red: 11
HS CAN High: Orange/Black, pin 6
HS CAN Low: Orange/Brown, pin 14
(+) Parking Lights: White/Black, pin 1
1
2
4
5
6
7
9
10
3
8
CUT
6
14
1
8
9
16
12
29
28
42 25 1
52 41 24 11
FT CAN Low: Orange/Brown, pin 3
(+) Ignition:
Black, pin 14
(+) Starter: Red/Black or
Red/Brown,pin 6
FT CAN High: Orange/Green, pin 4
Brown VESCM connector C
(+) Brake: Black/Red, pin 17
Steering column module
(behind steering column trim)
[5] Diode 1A
[5] Diode 1A
Headlight switch
(black conn. at
light switch)
(+) 12V:
Red/White or
Red/Yellow,
pin 42
Parking Lights Interrupt:
Red/White, pin 8
B
C
A
VESCM - Driver side under dashboard
(+) Parking Light Output: Blue/Red: 2
Parking Light Interrupt (vehicle side): Blue: 3
Diagnostic
Connector
OBDII
22 810 12
4 2442
DS4+
DS4
Slide
to open
Proper Fuse
Positioning
DS4+ DS4
It is important to check that the
fuses are positioned correctly.
MAIN (5A) (+)
(-) RLY3 PK LIGHT (15A) (+)
(-) ACC & START (30A) (+)
(-) FLEX RLY (20A) (+)
IGN (20A) (+)
MAIN (5A) (+)
(-) RLY3/PK LIGHT(15A) (+)
5
5
30
20
20
12
DS4+ VW10
© 2017-11-02 Directed. All rights reserved.
Vehicle wiring reference chart
This section provides vehicle wiring information to guide you through the various stages of your installation. Refer to
www.directechs.com for additional information.
Wire Information Connector Information
Function Color Pin Polarity Location Color Pins Ref.
Volkswagen Golf 2010-2014
Parking Light White/Black 1 (+) Headlight Switch. Black 10 A
Parking Light Interrupt Red/White 8 Cut Headlight Switch. Black 10 A
Ignition Black 14 (+) Steering column module. White 16 B
Starter Red/Black or Red/Brown 6 (+) Steering column module. White 16 B
FT CAN High Orange/Green 4 Data Steering column module. White 16 B
FT CAN Low Orange/Brown 3 Data Steering column module. White 16 B
HS CAN High Orange/Black 6 Data OBDII. Violet/Black 16 C
HS CAN Low Orange/Brown 14 Data OBDII. Violet/Black 16 C
12V Red/White or Red/Yellow 42 (+) VESCM connector C, under drivers dash. Brown 52 D
Brake Black/Red 17 (+) VESCM connector C, under drivers dash. Brown 52 D
Volkswagen GTI 2010-2014
Parking Light White/Black 1 (+) Headlight Switch. Black 10 A
Parking Light Interrupt Red/White 8 Cut Headlight Switch. Black 10 A
Ignition Black 14 (+) Steering column module. White 16 B
Starter Red/Black or Red/Brown 6 (+) Steering column module. White 16 B
FT CAN High Orange/Green 4 Data Steering column module. White 16 B
FT CAN Low Orange/Brown 3 Data Steering column module. White 16 B
HS CAN High Orange/Black 6 Data OBDII. Violet/Black 16 C
HS CAN Low Orange/Brown 14 Data OBDII. Violet/Black 16 C
12V Red/White or Red/Yellow 42 (+) VESCM connector C, under drivers dash. Brown 52 D
Brake Black/Red 17 (+) VESCM connector C, under drivers dash. Brown 52 D
13
DS4+ VW10
© 2017-11-02 Directed. All rights reserved.
Wire Information Connector Information
Function Color Pin Polarity Location Color Pins Ref.
Volkswagen Passat 2012-2017
Parking Light White/Black 1 (+) Headlight Switch. Black 10 A
Parking Light Interrupt Red/White or Red/Yellow 8 Cut Headlight Switch. Black 10 A
Ignition Black 14 (+) Steering column module. Black 16 B
Starter Red/Black or Red/Brown 6 (+) Steering column module. White 16 B
FT CAN High Orange/Green 4 Data Steering column module. Black 16 B
FT CAN Low Orange/Brown 3 Data Steering column module. Black 16 B
HS CAN High Orange/Black 6 Data OBDII. Violet/Black 16 C
HS CAN Low Orange/Brown 14 Data OBDII. Violet/Black 16 C
12V Red/White or Red /Yellow 42 (+) VESCM connector C, under drivers dash. Brown 52 D
Brake Black/Red 17 (+) VESCM connector C, under drivers dash. Brown 52 D
14
DS4+ VW10
© 2017-11-02 Directed. All rights reserved.
Type 3
Refer to "Pre-installation and application warnings" on page 4 for important information, such as the description of special notes referenced in the diagram ( ).
37
63
73
17
16
1
73
16
37
6317
1
16
8
9
1
Key Wrap: Lt. Green: 8
Key Wrap: Lt. Green/White: 9
(-) Ground: Black: 10
(+) Accessory Output: White: 5 & 11
HS CAN 1 Low: Tan : 1
(+) Starter / Brake Activation Output: White: 7
(-) Trunk Release Output: Red/White: 4
(+) Ignition Output: Violet/Black: 8
HS CAN 1 High: Tan/Black: 2
FT CAN High: Orange/Green: 4
FT CAN Low: Orange/Brown: 3
(MUX) Lock/Unlock Output: Violet/Brown: 6
Siren
Hood Pin
(+) 12V Input: Red: 6 & 12
Key Wrap: Lt.Green/Red: 7
(-) Hood Input: Gray: 21
(+) Siren Output: Brown/Red: 11
HS CAN High: Orange/Black, pin 6
HS CAN Low: Orange/Brown, pin 14
(+) Ignition:
Black/Violet, pin 8
(+) Starter: Red/Black, pin 4
FT CAN High:
Orange/Green, pin 20
FT CAN Low:
Orange/Brown, pin 21
Diagnostic
Connector OBDII
White VESCM Connector B
(under drivers kick)
1
2
4
5
6
7
9
10
3
8
(-) Trunk Release:
Violet, pin 23
(MUX) Doorlock:
Blue/Red,pin 24
(+) 12V:
Red/White
or Red/Yellow, pin 68
(+) Brake:
Black/Red, pin 39
Black VESCM connector A
(under drivers kick)
(+) Accessory: Black/Red, pin 3
Ignition Switch
(black conn. at
ignition switch)
VESCM - (under drivers kick)
ConnectorConnector
B
A
Diode 1A
Diode 1A
22 810 12
4 2442
DS4+
DS4
Slide
to open
Proper Fuse
Positioning
DS4+ DS4
5
15
30
20
20
5
15
30
20
20
5
15
30
20
20
5
15
30
20
20
5
15
30
20
20
5
15
30
20
20
MAIN (5A) (+)
(-) RLY3 PK LIGHT (15A) (+)
(-) ACC & START (30A) (+)
(-) FLEX RLY (20A) (+)
IGN (20A) (+)
MAIN (5A) (+)
(-) RLY3 PK LIGHT (15A) (+)
(-) ACC & START (30A) (+)
(-) FLEX RLY (20A) (+)
IGN (20A) (+)
MAIN (5A) (+)
(-) RLY3 PK LIGHT (15A) (+)
(-) ACC & START (30A) (+)
(-) FLEX RLY (20A) (+)
IGN (20A) (+)
MAIN (5A) (+)
(-) RLY3 PK LIGHT (15A) (+)
(-) ACC & START (30A) (+)
(-) FLEX RLY (20A) (+)
IGN (20A) (+)
MAIN (5A) (+)
(-) RLY3 PK LIGHT (15A) (+)
(-) ACC & START (30A) (+)
(-) FLEX RLY (20A) (+)
IGN (20A) (+)
MAIN (5A) (+)
(-) RLY3 PK LIGHT (15A) (+)
(-) ACC & START (30A) (+)
(-) FLEX RLY (20A) (+)
IGN (20A) (+)
It is important to check that the
fuses are positioned correctly.
5
15
5
15
MAIN (5A) (+)
(-) RLY3/PK LIGHT(15A) (+)
MAIN (5A) (+)
(-) RLY3/PK LIGHT(15A) (+)
5
15
30
20
20
5
15
30
20
20
5
15
30
20
20
5
15
30
20
20
5
15
30
20
20
5
15
30
20
20
MAIN (5A) (+)
(-) RLY3 PK LIGHT (15A) (+)
(-) ACC & START (30A) (+)
(-) FLEX RLY (20A) (+)
IGN (20A) (+)
MAIN (5A) (+)
(-) RLY3 PK LIGHT (15A) (+)
(-) ACC & START (30A) (+)
(-) FLEX RLY (20A) (+)
IGN (20A) (+)
MAIN (5A) (+)
(-) RLY3 PK LIGHT (15A) (+)
(-) ACC & START (30A) (+)
(-) FLEX RLY (20A) (+)
IGN (20A) (+)
MAIN (5A) (+)
(-) RLY3 PK LIGHT (15A) (+)
(-) ACC & START (30A) (+)
(-) FLEX RLY (20A) (+)
IGN (20A) (+)
MAIN (5A) (+)
(-) RLY3 PK LIGHT (15A) (+)
(-) ACC & START (30A) (+)
(-) FLEX RLY (20A) (+)
IGN (20A) (+)
MAIN (5A) (+)
(-) RLY3 PK LIGHT (15A) (+)
(-) ACC & START (30A) (+)
(-) FLEX RLY (20A) (+)
IGN (20A) (+)
5
15
30
20
20
5
15
30
20
20
5
15
30
20
20
5
15
30
20
20
5
15
30
20
20
5
15
30
20
20
MAIN (5A) (+)
(-) RLY3 PK LIGHT (15A) (+)
(-) ACC & START (30A) (+)
(-) FLEX RLY (20A) (+)
IGN (20A) (+)
MAIN (5A) (+)
(-) RLY3 PK LIGHT (15A) (+)
(-) ACC & START (30A) (+)
(-) FLEX RLY (20A) (+)
IGN (20A) (+)
MAIN (5A) (+)
(-) RLY3 PK LIGHT (15A) (+)
(-) ACC & START (30A) (+)
(-) FLEX RLY (20A) (+)
IGN (20A) (+)
MAIN (5A) (+)
(-) RLY3 PK LIGHT (15A) (+)
(-) ACC & START (30A) (+)
(-) FLEX RLY (20A) (+)
IGN (20A) (+)
MAIN (5A) (+)
(-) RLY3 PK LIGHT (15A) (+)
(-) ACC & START (30A) (+)
(-) FLEX RLY (20A) (+)
IGN (20A) (+)
MAIN (5A) (+)
(-) RLY3 PK LIGHT (15A) (+)
(-) ACC & START (30A) (+)
(-) FLEX RLY (20A) (+)
IGN (20A) (+)
5
15
5
15
MAIN (5A) (+)
(-) RLY3/PK LIGHT(15A) (+)
MAIN (5A) (+)
(-) RLY3/PK LIGHT(15A) (+)
(+) 12V Input: Blue/Red: 2
(+) Parking Light Output: Blue: 3
Parking Light Switch
(black conn. at light switch)
(+) Parking Lights:
Gray/Red, pin 14
1
9
10
17
14
15
DS4+ VW10
© 2017-11-02 Directed. All rights reserved.
Vehicle wiring reference chart
This section provides vehicle wiring information to guide you through the various stages of your installation. Refer to
www.directechs.com for additional information.
Wire Information Connector Information
Function Color Pin Polarity Location Color Pins Ref.
Volkswagen Jetta 2011-2014
Starter Red/Black 4 (+) Ignition switch. Black 10 A
Ignition Black/Violet 8 (+) Ignition switch. Black 10 A
Accessory Black/Red 3 (+) Ignition switch. Black 10 A
HS CAN High Orange/Black 6 Data OBDII. Violet/Black 16 B
HS CAN Low Orange/Brown 14 Data OBDII. Violet/Black 16 B
Parking Light Gray/Red 14 (+) Headlight switch. Black 17 C
FT CAN High Orange/Green 20 Data VESCM connector B, under drivers dash. White 73 D
FT CAN Low Orange/Brown 21 Data VESCM connector B, under drivers dash. White 73 D
12V Red/White or Red/Yellow 68 (+) VESCM connector A, under drivers dash. Black 73 E
Brake Black/Red 39 (+) VESCM connector A, under drivers dash. Black 73 E
Doorlocks [4] Blue/Red 24 MUX VESCM connector A, under drivers dash. Black 73 E
Trunk Release [4] Violet 23 (-) VESCM connector A, under drivers dash. Black 73 E
16
DS4+ VW10
© 2017-11-02 Directed. All rights reserved.
Type 4
Refer to "Pre-installation and application warnings" on page 4 for important information, such as the description of special notes referenced in the diagram ( ).
16
8
9
1
Siren
Hood Pin
HS CAN High: Orange/Black, pin 6
HS CAN Low: Orange/Brown, pin 14
Steering Column Control Unit
12
29
28
42 25 1
52 41 24 11
FT CAN Low:
Orange/Brown, pin 15
(+) Ignition: Pin 17
(+) Starter: Red/Black
or Black/Gray,pin 18
FT CAN High: Orange/Green, pin 14
Brown VESCM connector C
(+) Brake: Black/Red, pin 17
(+)12V: Red/Blue or Red/Violet, pin 42
Steering Column Module
(behind steering
column trim)
17
10
1
20
[5] Diode 1A
[5] Diode 1A
Key Wrap: Lt. Green: 8
Key Wrap: Lt. Green/White: 9
(-) Ground: Black: 10
HS CAN Low: Tan : 1
(+) Starter / Brake Activation Output: White: 7
(-) Parking Lights Output: Lt.Green/Black: 1
(+) Ignition Output: Violet/Black: 8
HS CAN High: Tan/Black: 2
FT CAN High: Orange/Green: 4
FT CAN Low: Orange/Brown: 3
(+) 12V Input: Red: 6 & 12
Key Wrap: Lt.Green/Red: 7
(-) Hood Input: Gray: 21
(+) Siren Output: Brown/Red: 11
B
C
A
VESCM - Driver side under dashboard
Diagnostic
Connector
OBDII
22 810 12
4 2442
DS4+
DS4
Slide
to open
Proper Fuse
Positioning
DS4+ DS4
It is important to check that the
fuses are positioned correctly.
MAIN (5A) (+)
(-) RLY3 PK LIGHT (15A) (+)
(-) ACC & START (30A) (+)
(-) FLEX RLY (20A) (+)
IGN (20A) (+)
MAIN (5A) (+)
(-) RLY3/PK LIGHT(15A) (+)
5
5
30
20
20
(-) Parking Lights:
Black/White, pin 19
12
29
28
42 25 1
52 41 24 11
Black VESCM connector A
17
DS4+ VW10
© 2017-11-02 Directed. All rights reserved.
Vehicle wiring reference chart
This section provides vehicle wiring information to guide you through the various stages of your installation. Refer to
www.directechs.com for additional information.
Wire Information Connector Information
Function Color Pin Polarity Location Color Pins Ref.
Audi A3 2009-2013
HS CAN High Orange/Black 6 Data OBDII. Violet/Black 16 A
HS CAN Low Orange/Brown 14 Data OBDII. Violet/Black 16 A
Starter Red/Black 18 (+) Steering column module behind steering column trim. Black 20 B
Ignition Black/Green 17 (+) Steering column module behind steering column trim. Black 20 B
FT CAN High Orange/Green 14 Data Steering column module behind steering column trim. Black 20 B
FT CAN Low Orange/Brown 15 Data Steering column module behind steering column trim. Black 20 B
12V Red/Blue 42 (+) VESCM, connector C, under drivers dash. Brown 52 C
Brake Black/Yellow 17 (+) VESCM, connector C, under drivers dash. Brown 52 C
Parking Lights Gray/Yellow 19 (-) VESCM, connector A, under drivers dash. Black 52 D
Audi R8 2010-2014
HS CAN High Orange/Black 6 Data OBDII. Violet/Black 16 A
HS CAN Low Orange/Brown 14 Data OBDII. Violet/Black 16 A
Starter Black/Gray 18 (+) Steering column module behind steering column trim. Black 20 B
Ignition Black/Violet 17 (+) Steering column module behind steering column trim. Black 20 B
FT CAN High Orange/Green 14 Data Steering column module behind steering column trim. Black 20 B
FT CAN Low Orange/Brown 15 Data Steering column module behind steering column trim. Black 20 B
12V Red/Violet 42 (+) VESCM, connector C, below glove box. Brown 52 E
Brake Red/Black 17 (+) VESCM, connector C, below glove box. Brown 52 E
Parking Lights Black/White 19 (-) VESCM, connector A, below glove box. Black 52 F
Audi TT 2010-2015
HS CAN High Orange/Black 6 Data OBDII. Violet/Black 16 A
HS CAN Low Orange/Brown 14 Data OBDII. Violet/Black 16 A
Starter Red/Black 18 (+) Steering column module behind steering column trim. Black 20 B
Ignition Black/White 17 (+) Steering column module behind steering column trim. Black 20 B
FT CAN High Orange/Green 14 Data Steering column module behind steering column trim. Black 20 B
FT CAN Low Orange/Brown 15 Data Steering column module behind steering column trim. Black 20 B
12V Red/Violet 42 (+) VESCM, connector C, under drivers dash. Brown 52 C
Brake Black/Yellow 17 (+) VESCM, connector C, under drivers dash. Brown 52 C
Parking Lights Gray/Yellow 19 (-) VESCM, connector A, under drivers dash. Black 52 D
18
DS4+ VW10
© 2017-11-02 Directed. All rights reserved.
Type 5
Refer to "Pre-installation and application warnings" on page 4 for important information, such as the description of special notes referenced in the diagram ( )
16
8
9
1
Siren
Hood Pin
HS CAN High:
Orange/Black, pin 6
HS CAN Low:
Orange/Brown,
pin 14
Key Wrap: Lt. Green: 8
Key Wrap: Lt. Green/White: 9
(-) Ground: Black: 10
HS CAN 1 Low: Tan : 1
(+) Starter / Brake Activation Output: White: 7
(+) Ignition Output: Violet/Black: 8
HS CAN 1 High: Tan/Black: 2
FT CAN High: Orange/Green: 4
FT CAN Low: Orange/Brown: 3
(+) 12V Input: Red: 6 & 12
Key Wrap: Lt.Green/Red: 7
(-) Hood Input: Gray: 21
(+) Siren Output: Brown/Red: 11
12
29
28
42 25 1
52 41 24 11
Brown VESCM connector C
(+) Brake: Black/Red, pin 17
(-) Hazards: Brown/Red, pin 7
(+) 12V:
Red/Yellow,
pin 42
[5] Diode 1A
6
14
1
8
9
16
FT CAN Low: Orange/Brown, pin 3
(+) Ignition:
Green/Black, pin 14
(+) Starter: Red/Black,pin 6
FT CAN High: Orange/Green or Lt.Green, pin 4
Steering Column Module
(behind steering column trim)
[5] Diode 1A
(-) Hazards Output: Lt.Green/Black: 1
B
C
A
VESCM - Driver side under dashboard
Diagnostic
Connector
OBDII
22 810 12
4 2442
DS4+
DS4
Slide
to open
Proper Fuse
Positioning
DS4+ DS4
It is important to check that the
fuses are positioned correctly.
MAIN (5A) (+)
(-) RLY3 PK LIGHT (15A) (+)
(-) ACC & START (30A) (+)
(-) FLEX RLY (20A) (+)
IGN (20A) (+)
MAIN (5A) (+)
(-) RLY3/PK LIGHT(15A) (+)
5
5
30
20
20
19
DS4+ VW10
© 2017-11-02 Directed. All rights reserved.
Vehicle wiring reference chart
This section provides vehicle wiring information to guide you through the various stages of your installation. Refer to
www.directechs.com for additional information.
Wire Information Connector Information
Function Color Pin Polarity Location Color Pins Ref.
Audi Q3 2015-2017
HS CAN High Orange/Black 6 Data OBDII. Violet/Black 16 A
HS CAN Low Orange/Brown 14 Data OBDII. Violet/Black 16 A
Starter Red/Black 6 (+) Steering column module behind steering column trim. Black 16 B
Ignition Green/Black 14 (+) Steering column module behind steering column trim. Black 16 B
FT CAN High
Orange/Green or
Lt.Green
4 Data Steering column module behind steering column trim. Black 16 B
FT CAN Low Orange/Brown 3 Data Steering column module behind steering column trim. Black 16 B
12V Red/Yellow 42 (+) VESCM connector C, under drivers dash. Brown 52 C
Hazards Brown/Red 7 (-) VESCM connector C, under drivers dash. Brown 52 C
Brake Black/Red 17 (+) VESCM connector C, under drivers dash. Brown 52 C
20
DS4+ VW10
© 2017-11-02 Directed. All rights reserved.
Type 6
Refer to "Pre-installation and application warnings" on page 4 for important information, such as the description of special notes referenced in the diagram ( ).
16
8
9
1
Siren
Hood Pin
HS CAN High:
Orange/Black, pin 6
HS CAN Low:
Orange/Brown, pin 14
1
2
4
5
6
7
9
10
3
8
Headlight Switch
(black conn. at light switch)
CUT
Parking Light Interrupt (conn. side): Blue/White: 1
Key Wrap: Lt. Green: 8
Key Wrap: Lt. Green/White: 9
(-) Ground: Black: 10
HS CAN 1 Low: Tan : 1
(+) Starter / Brake Activation Output: White: 7
(+) Ignition Output: Violet/Black: 8
HS CAN 1 High: Tan/Black: 2
FT CAN High: Orange/Green: 4
FT CAN Low: Orange/Brown: 3
(+) 12V Input: Red: 6 & 12
Key Wrap: Lt.Green/Red: 7
(-) Hood Input: Gray: 21
(+) Siren Output: Brown/Red: 11
6
14
1
8
9
16
12
29
28
42 25 1
52 41 24 11
FT CAN Low:
Orange/Brown, pin 16
(+) Ignition:
Red/Green or
Violet/Yellow,
pin 5
(+) Keysense:
Green or
Green/Blue, pin 16
(+) Starter: Pin 6
FT CAN High:
Orange/Green, pin 15
Brown VESCM connector C
[5] (+) Brake: Black/Red, pin 17
(+) 12V:
Red/Yellow,
pin 42
Parking Lights Interrupt:
Red/White or Red/Black, pin 8
(+) Parking Lights: Gray/Yellow
or Gray/Green, pin 3
Steering Column Module
(behind steering column trim)
(-) Key Release Output: Blue/White: 2
Ignition Switch Plug
(at Key Port)
30
86
85
87
87a
Fuse 5A
[5] Diode 1A
[5] Diode 1A
Diagnostic
Connector OBDII
(+)12V
B
C
A
VESCM - Driver side under dashboard
(+) Parking Light Output: Blue/Red: 2
Parking Light Interrupt (vehicle side): Blue: 3
22 810 12
4 2442
DS4+
DS4
Slide
to open
Proper Fuse
Positioning
DS4+ DS4
It is important to check that the
fuses are positioned correctly.
MAIN (5A) (+)
(-) RLY3 PK LIGHT (15A) (+)
(-) ACC & START (30A) (+)
(-) FLEX RLY (20A) (+)
IGN (20A) (+)
MAIN (5A) (+)
(-) RLY3/PK LIGHT(15A) (+)
5
5
30
20
20
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25
  • Page 26 26
  • Page 27 27
  • Page 28 28
  • Page 29 29
  • Page 30 30
  • Page 31 31
  • Page 32 32
  • Page 33 33
  • Page 34 34
  • Page 35 35
  • Page 36 36
  • Page 37 37
  • Page 38 38
  • Page 39 39
  • Page 40 40
  • Page 41 41
  • Page 42 42
  • Page 43 43
  • Page 44 44

Directed DS4+ Installation guide

Type
Installation guide

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI