Directed DBALL-GM10 XPRESSKIT Quick Reference Manual

Directed
Brand
Directed
Model
DBALL-GM10 XPRESSKIT
Category
Remote starters
Type
Quick Reference Manual
Index
† Buick, Chevrolet and GMC are registered trademarks and property of .their respective companies.
Vehicle Application Guide................................................................................................................................................
Installation
Type 1..............................................................................................................................................................................
Vehicle Wiring Reference Chart - Type 1 (pages 4-6).....................................................................................................
Type 2..............................................................................................................................................................................
Vehicle Wiring Reference Chart - Type 2.........................................................................................................................
Installation with T-Harness...............................................................................................................................................
Module Reset & Hard Reset............................................................................................................................................
Feature & Option List.......................................................................................................................................................
02
03
04
07
08
09
Programming
..................................................................................................................... 10
11
12
Feature Programming...................................................................................................................................................... 13
LED Diagnostics & Troubleshooting................................................................................................................................ 14
Limited One-Year Consumer Warranty............................................................................................................................ 15
Module Programming.................................
Data override and door lock interface compatible with new generation GM vehicles with a
BLADE-type key (i.e. Camaro, Equinox and Lacrosse). The available features include:
Transponder override (no key required); door lock control; factory security control; trunk
release; door, hood and trunk sensing; tach sensing; and much more.
Refer to Quick Reference Guide (QRG) at the end of this guide for more information on how
to use the various features offered with this product.
Installation Guide
Update Alert: Firmware updates are posted on the web on a regular basis. We recommend
that you check for firmware and/or install guide updates prior to installing this product.
Important:
This guide is compatible with the GM10 firmware version 2.08 and higher.
Rev.: 20130304
Platform: DBALL
Firmware: GM10 v. 2.08+
© 2012 Directed. All rights reserved.
Vehicle Application Guide
Page 2
The following table lists the vehicles and features which are compatible with this product. The number assigned to each
year allows you to determine which installation type should be used for your vehicle.
Vehicles
2013
2012
2011
2010
CC-Heated Seats Activation
DL-Arm Factory Security
DL-Disarm Factory Security
DL-Door Lock Control
DL-Door Unlock
DL-Driver Priority Unlock
FOB-Control of aftermarket alarm with OEM remote
PK-Immobilizer Bypass-Data No Key Req'd
RS-Ignition Activation
RS-RAP Shut Down (Retained ACC Power)
RS-Tach / RPM Output
SS-Entry Monitoring ALL Door Pins
SS-Entry Monitoring Driver Door Pin
SS-Entry Monitoring Hood Pin
SS-Entry Monitoring Trunk/Hatch Pin
ST-Brake Status (foot brake)
ST-Hand Brake Status
ST-Ignition Status
Buick
Encore 1 • • • • • D • • • • D • • • •
LaCrosse 1 • • • • • D • • • • D • • • •
LaCrosse 1 1 1 • • • • • D • • • • D • • • • D
Regal 1 • • • • • D • • • • D • • • •
Regal 1 1 • • • • • D • • • • D • • • • D
Verano 1 1 • • • • • D • • • • D • • • •
Chevrolet
Camaro 1 • • • • • • D • • • • D • • • •
Camaro 1 • • • • • • D • • • • D • • • • D
Camaro 1 1 • • • • • D • • • • D • • • • D
Cruze 1 • • • • • D • • • • D • • • •
Cruze 1 • • • • • D • • • • • D • • • • D
Cruze 1 • • • • • D • • • • D • • • • D
Equinox 1 1 • • • • • • D • • • • D • • • • D
Equinox 1 1 • • • • • D • • • • D • • • • D
Malibu 1 • • • • • D • • • • D • • • •
Orlando 2 • • • • • D • • • • D • • • •
Orlando 2 • • • • • D • • • • D • • • • D
Sonic 2 2 • • • • • D • • • • D • • • •
Spark 1 • • • • • D • • • • D • • • •
Trax 1 • • • • • D • • • • D • • • •
GMC
Terrain 1 1 1 1 • • • • • D • • • • D • • • • D
Legend:
D: Data-to-Data (D2D) only CC: Comfort & Convenience Controls RS: Remote Start & Engine Controls
•: D2D and W2W DL: OE Door Lock & Alarm Controls SS: Integrated Security & Monitoring
FOB: Sync CAN Interface w/ FOB Remote ST: Function/Feature Status
PK: Transponder & Immobilizer Override
Rev.: 20130304
Platform: DBALL
Firmware: GM10 v. 2.08+
© 2012 Directed. All rights reserved.
BA C
Installation Type 1
Page 3
Not required in D2D mode.
Wires are listed by pin numbers. This display is not representative of connector pin layouts, which are often stacked.
* These wires are optional connections required on some remote starters, which do not support the signals in D2D.
** If the RAP OFF wire is not connected, the radio will turn OFF but some lights will remain ON in the central console for 10 minutes. Connect this wire
(Green/Black, pin 2/12) to the driver door sense trigger to avoid the issue.
*** Use (-) Aux or any (-) trigger to activate the heated seats function during run time.
† Heated seat feature must be enable, see Feature Programming (page 12).
(-) Parking Lights
(AC) Tach Input*
(+) Brake Input
(-) Trunk Status Input
(-) Door Status Input
Remote
Starter
(-) GWR (Status)
(+) Starter Output
(+) Ignition Output
(-)Trunk Output
(-) Lock Output
(-) Unlock Output
(-) Aux3***
(+) 12v(+) 12v
(-) Ground
(-) Hood Status Input
1: Green: (-) Lock Input
2: Blue: (-) Unlock Input
3: Red/White: (-) Trunk Input
10: Blue/White: (-) GWR (Status) Input
†
6: White/Black: (-) Heated Seats
8: Violet: (+) Starter Input
TX
(-) Ground
RX
(+)12v
10
DBALL
RF
Programming button
LED
4
14 12 2
1: Light Green: Single Wire CAN
11: Yellow/Red: Relay 2 Com
12: Brown/Red: Relay 2 NO
10: Orange/Red: Relay 2 NC
5: Violet/White: (AC) Tach Output*
6: Gray: (+) Brake Output
12: Blue/Red: (-) Hood Status Output
3: Green/White: (-) Door Status Output
1: Black/White: (-) Handbrake Status Output*
4: Red/Black: (-) Trunk Status Output
2: Green/Black: RAP OFF**
11: Orange/Black: Data Bypass
Clutch Switch
(black connector)
For manual
transmission
vehicles only.
10: Yellow/Black: Data Bypass
Yellow
(On the Camaro and Cruze vehicles)
8: Purple/Green: MUX
7: Gray/Black: (+) Accessory Output
9: Purple/Brown: MUX
XKD2D65
(-) Ground
14: Black: (-) Ground(-) Ground
13: Red: (+) 12v
(+) 12v
(-) Driver
Door Sense
Trigger**
Cut
(-) Handbrake Status Input*
White
Lt. Blue
Lt. Green
Pin 22
Pin 5
Pin 6
Pin 2
Refer to pages 4-6 for information
on the BCM connections for each
vehicle.
BCM (under driver-side of dash)
1 8
169
3:Tan/Black: HSCAN High
4:Tan: HSCAN Low
Pin 6
Pin 14
Pin 1
OBDII
Diagnostic Connector
Rev.: 20130304
Platform: DBALL
Firmware: GM10 v. 2.08+
© 2012 Directed. All rights reserved.
Color Pin Color No. Pins Location
Ignition Pink or Blue 6 Lt Green 25 BCM, under driver-side dash, above driver-kick panel
Accessory Brown or Violet 5 Lt Green 25 BCM, under driver-side dash, above driver-kick panel
Parking Lights Lt Blue or Lt. Green 22 White 26 BCM, under driver-side dash, above driver-kick panel
Data Lt Blue or Green/Violet 2 Lt Green 25 BCM, under driver-side dash, above driver-kick panel
RAP OFF Gray 6 Black 7 Driver Window Switch, in driver's door
SW CAN Dk Green 1 Black 16 OBDII
CAN High Tan/Black or Blue 6 Black 16 OBDII
CAN Low Tan or White 14 Black 16 OBDII
Description
ConnectorWire
Page 4
Vehicle Wiring Reference Charts - Type 1
Buick LaCrosse
Wire colors should only be used as a reference. You should always test a wire's function and pin location before
connecting to it.
Color Pin Color No. Pins Location
Ignition Violet/Yellow or Violet/Black 6 Lt. Green 25 BCM, under driver-side dash, above driver-kick panel
Accessory Brown/Yellow or Violet/Yellow 5 Lt. Green 25 BCM, under driver-side dash, above driver-kick panel
Parking Lights Lt. or Dk. Green/Gray 22 White 26 BCM, under driver-side dash, above driver-kick panel
Data Lt. Blue or Dk. Green/Violet 2 Lt. Green 25 BCM, under driver-side dash, above driver-kick panel
RAP OFF Gray 6 Black 7 Driver Window Switch, in driver's door
SW CAN Dk. Green 1 Black 16 OBDII
CAN High Tan/Black or Blue 6 Black 16 OBDII
CAN Low Tan or White 14 Black 16 OBDII
Description
ConnectorWire
Buick Regal
Color Pin Color No. Pins Location
Ignition Violet/Black 6 Lt Green 25 BCM, under driver-side dash, above driver-kick panel
Accessory Violet/Yellow 5 Lt Green 25 BCM, under driver-side dash, above driver-kick panel
Parking Lights Green/Gray 22 White 26 BCM, under driver-side dash, above driver-kick panel
Data Green/Violet 2 Lt Green 25 BCM, under driver-side dash, above driver-kick panel
RAP OFF Gray 6 Black 7 Driver Window Motor, in driver's door
SW CAN Dk Green 1 Black 16 OBDII
CAN High Blue 6 Black 16 OBDII
CAN Low White 14 Black 16 OBDII
Description
ConnectorWire
Buick Encore
Color Pin Color No. Pins Location
Ignition Violet/Black 6 Lt Green 25 BCM, under driver-side dash, above driver-kick panel
Accessory Violet/Yellow 5 Lt Green 25 BCM, under driver-side dash, above driver-kick panel
Parking Lights Green/Gray 22 White 26 BCM, under driver-side dash, above driver-kick panel
Data Green/Violet 2 Lt Green 25 BCM, under driver-side dash, above driver-kick panel
RAP OFF Gray 6 Black 7 Driver Window Motor, in driver's door
SW CAN Dk Green 1 Black 16 OBDII
CAN High Blue 6 Black 16 OBDII
CAN Low White 14 Black 16 OBDII
Description
ConnectorWire
Buick Verano
Rev.: 20130304
Platform: DBALL
Firmware: GM10 v. 2.08+
© 2012 Directed. All rights reserved.
Color Pin Color No. Pins Location
Ignition Pink 6 Lt. Green 25 BCM, under driver-side dash, above accelerator pedal
Accessory Brown 5 Lt. Green 25 BCM, under driver-side dash, above accelerator pedal
Parking Lights Lt. Blue 22 White 26 BCM, under driver-side dash, above accelerator pedal
Data Lt. Blue 2 Lt. Green 25 BCM, under driver-side dash, above accelerator pedal
RAP OFF Gray/Black 6 Black 7 Driver Window Switch, in driver's door
SW CAN Dk. Green 1 Black 16 OBDII
CAN High Tan/Black or Blue 6 Black 16 OBDII
CAN Low Tan or White 14 Black 16 OBDII
Description
ConnectorWire
Chevrolet Camaro
Color Pin Color No. Pins Location
Ignition Pink 6 Lt. Green 25 BCM, under driver-side dash, above driver-kick panel
Accessory Brown 5 Lt. Green 25 BCM, under driver-side dash, above driver-kick panel
Parking Lights Lt. Blue 22 White 26 BCM, under driver-side dash, above driver-kick panel
Data Lt. Blue 2 Lt. Green 25 BCM, under driver-side dash, above driver-kick panel
RAP OFF Gray/Black 6 Black 8 Driver Window Switch, in driver's door
SW CAN Dk. Green 1 Black 16 OBDII
CAN High Tan/Black or Blue 6 Black 16 OBDII
CAN Low Tan or White 14 Black 16 OBDII
Description
ConnectorWire
Color Pin Color No. Pins Location
Ignition Violet 6 Lt Green 25 BCM, under driver-side dash, above driver-kick panel
Accessory Yellow 5 Lt Green 25 BCM, under driver-side dash, above driver-kick panel
Parking Lights Gray 22 White 26 BCM, under driver-side dash, above driver-kick panel
Data Green/Violet 2 Lt Green 25 BCM, under driver-side dash, above driver-kick panel
RAP OFF Gray 6 Black 8 or 7 Driver Window Switch or Motor, in driver's door
SW CAN Dk Green 1 Black 16 OBDII
CAN High Blue 6 Black 16 OBDII
CAN Low White 14 Black 16 OBDII
Description
ConnectorWire
Chevrolet Equinox
Chevrolet Malibu
Color Pin Color No. Pins Location
Ignition Violet/Black 6 Lt Green 25 BCM, under passenger-side of center dash
Accessory Violet/Yellow 5 Lt Green 25 BCM, under passenger-side of center dash
Parking Lights Dk Green/Gray 22 White 26 BCM, under passenger-side of center dash
Data Dk Green/Violet 2 Lt Green 25 BCM, under passenger-side of center dash
RAP OFF Gray 6 Black 8 Driver Window Switch, in driver's door*
SW CAN Dk Green 1 Black 16 OBDII
CAN High Tan/Black or Blue 6 Black 16 OBDII
CAN Low Tan or White 14 Black 16 OBDII
* On vehicles with express up and down windows, the wire is at the driver window motor, black 7-pin plug, pin 6.
Description
ConnectorWire
Chevrolet Cruze
Page 5
Vehicle Wiring Reference Charts - Type 1
Wire colors should only be used as a reference. You should always test a wire's function and pin location before
connecting to it.
Rev.: 20130304
Platform: DBALL
Firmware: GM10 v. 2.08+
© 2012 Directed. All rights reserved.
Color Pin Color No. Pins Location
Ignition Pink 6 Lt. Green 25 BCM, under driver-side dash, above driver-kick panel
Accessory Brown 5 Lt. Green 25 BCM, under driver-side dash, above driver-kick panel
Parking Lights Lt. Blue 22 White 26 BCM, under driver-side dash, above driver-kick panel
Data Lt. Blue 2 Lt. Green 25 BCM, under driver-side dash, above driver-kick panel
RAP OFF Gray/Black 6 Black 8 Driver Window Switch, in driver's door
SW CAN Dk. Green 1 Black 16 OBDII
CAN High Tan/Black or Blue 6 Black 16 OBDII
CAN Low Tan or White 14 Black 16 OBDII
Description
ConnectorWire
Color Pin Color No. Pins Location
Ignition Violet/Black 6 Lt Green 25 BCM, under driver-side dash, above driver-kick panel
Accessory Violet/Yellow 5 Lt Green 25 BCM, under driver-side dash, above driver-kick panel
Parking Lights Green/Gray 22 White 26 BCM, under driver-side dash, above driver-kick panel
Data Green/Violet 2 Lt Green 25 BCM, under driver-side dash, above driver-kick panel
RAP OFF Gray 6 Black 7 Driver Window Motor, in driver's door
SW CAN Dk Green 1 Black 16 OBDII
CAN High Blue 6 Black 16 OBDII
CAN Low White 14 Black 16 OBDII
Description
ConnectorWire
Color Pin Color No. Pins Location
Ignition Violet/Black 6 Lt Green 25 BCM, under driver-side dash, above driver-kick panel
Accessory Violet/Yellow 5 Lt Green 25 BCM, under driver-side dash, above driver-kick panel
Parking Lights Green/Gray 22 White 26 BCM, under driver-side dash, above driver-kick panel
Data Green/Violet 2 Lt Green 25 BCM, under driver-side dash, above driver-kick panel
RAP OFF Gray 22 Pink 27 BCM, under driver-side dash, above driver-kick panel
SW CAN Dk Green 1 Black 16 OBDII
CAN High Blue 6 Black 16 OBDII
CAN Low White 14 Black 16 OBDII
Description
ConnectorWire
GMC Terrain
Chevrolet Trax
Chevrolet Spark
Page 6
Vehicle Wiring Reference Charts - Type 1
Wire colors should only be used as a reference. You should always test a wire's function and pin location before
connecting to it.
Rev.: 20130304
Platform: DBALL
Firmware: GM10 v. 2.08+
© 2012 Directed. All rights reserved.
Installation Type 2
Page 7
Not required in D2D mode.
Wires are listed by pin numbers. This display is not representative of connector pin layouts, which are often stacked.
* Tach wire is an optional connection required on some remote starters, which do not support a tach signal in D2D.
*** Use (-) Aux or any (-) trigger to activate the heated seats function during run time.
** If the RAP OFF wire is not connected, the radio will turn OFF but some lights will remain ON in the central console for 10 minutes. Connect this wire
(Green/Black, pin 2/12) to the driver door sense trigger (Gray/Black) to avoid the issue.
(-) Parking Lights
(AC) Tach Input*
(+) Brake Input
(-) Trunk Status Input
(-) Door Status Input
Remote
Starter
(-) GWR (Status)
(+) Ignition Output
(-)Trunk Output
(-) Lock Output
(-) Unlock Output
(-) Aux3***
(+) 12 V
(+) 12 V
(-) Ground
(-) Hood Status Input
10
DBALL
RF
Programming button
LED
1: Green: (-) Lock Input
2: Blue: (-) Unlock Input
3: Red/White: (-) Trunk Input
10: Blue/White: (-) GWR (Status) Input
6: White/Black: (-) Heated Seats
†
4
TX
(-) Ground
RX
(+)12v
14 12 2
1: Light Green: Single Wire CAN
Pin 1
Pin 6
11: Yellow/Red: Relay 2 Com
12: Brown/Red: Relay 2 NO
10: Orange/Red: Relay 2 NC
5: Violet/White: (AC) Tach Output*
6: Gray: (+) Brake Output
12: Blue/Red: (-) Hood Status Output
3: Green/White: (-) Door Status Output
4: Red/Black: (-) Trunk Status Output
2: Green/Black: RAP OFF**
11: Orange/Black: Data Bypass
10: Yellow/Black: Data Bypass
XKD2D65
(-) Ground
14: Black: (-) Ground(-) Ground
13: Red: (+) 12v
(+) 12v
OBDII
Diagnostic Connector
Light Switch
Connector
(-) Driver Door
Sense Trigger
(Gray/Black)**
Refer to the Vehicle Wiring
Reference Chart (page 8)
for wire color and location.
654321
Accessory, Pin 3
Ignition, Pin 1
Ignition
Control
Switch
321
Data Bypass, Pin 2
Immobilizer Control
Module (K89)
Cut
(-) Parking Lights
Refer to the Vehicle
Wiring Reference Chart
(page 8) for wire color
and location.
654321
121110987
1: Black/White: (-) Handbrake Status Output*
(-) Neutral Safety Input/(-) Handbrake Status Input*
7: Gray/Black: (+) Accessory Output
1 8
169
3:Tan/Black: HSCAN High
4:Tan: HSCAN Low
Pin 14
(+) Starter Output
8: Violet: (+) Starter Input
† Heated seat feature must be enable, see Feature Programming (page 12).
Rev.: 20130304
Platform: DBALL
Firmware: GM10 v. 2.08+
© 2012 Directed. All rights reserved.
Page 8
Locating Components in the Vehicle
Ignition Barrel
Immobilizer Control
Module ( )K89
Ignition Control
Switch
Color Pin Color No. Pins Location
Ignition Violet/Black 1 Black 6 Ignition Control Switch
Accessory Violet/Yellow 3 Black 6 Ignition Control Switch
Parking Lights Green/Gray 3 Black 12 Light Switch Connector
Data Green/Black 2 Violet 3 Immobilizer Control Module
RAP OFF Gray 6 Black 7 Driver Window Motor
SW CAN Dk. Green 1 Black 16 OBDII
CAN High Tan/Black or Blue 6 Black 16 OBDII
CAN Low Tan or White 14 Black 16 OBDII
Description
ConnectorWire
Chevrolet Orlando
Vehicle Wiring Reference Chart - Type 2
Color Pin Color No. Pins Location
Ignition Violet/Black 1 White 6 Ignition Control Switch
Accessory Violet/Yellow 3 White 6 Ignition Control Switch
Parking Lights Green/Gray 3 Black 12 Light Switch Connector
Data Green/Violet 2 Violet 3 Immobilizer Control Module
RAP OFF Gray 22 Pink 27 BCM Under Driver Dash (Express Down Windows)
RAP OFF Gray 6 Black 7 Driver Window Motor (Express Up/Down Windows)
SW CAN Dk Green 1 Black 16 OBDII
CAN High Tan/Black or Blue 6 Black 16 OBDII
CAN Low Tan or White 14 Black 16 OBDII
Description
ConnectorWire
Chevrolet Sonic
Rev.: 20130304
Platform: DBALL
Firmware: GM10 v. 2.08+
© 2012 Directed. All rights reserved.
Light Switch
Connector
(-) Parking Lights
Refer to the Vehicle
Wiring Reference Chart
(pages 4, 5, 6, and 8) for
wire color and location.
Installation with T-Harness
(for all GM10 vehicles)
Page 9
Wires are listed by pin numbers. This display is not representative of connector pin layouts, which are often stacked.
* If the RAP OFF wire is not connected, the radio will turn OFF but some lights will remain ON in the central console for 10 minutes. Connect this wire
(Green/Black, pin 2/12) to the driver door sense trigger (Gray/Black) to avoid the issue.
(-) Parking Lights
Remote
Starter
(+) Ignition Output
(-) Hood Status Input
(+) 12v(+) 12v
(-) Ground
(-) Ground
10
DBALL
RF
Programming button
LED
4
14 12 2
TX
(-) Ground
RX
(+) 12v
Remote Start Safety
Override Switch
Theft
Deterrent
Module (TDM)
connector
Vehicle side
to vehicle
6-pin connector
Ignition
Connector
To Theft Deterrent Module (TDM)
(under ignition switch,
black connector)
Use connectors
labeled GM10
NOT USED
NOT USED
2: Green/Black: (-) RAP OFF *
Black/White: NC
Cut away the 4-pin
connector and connect
the three wires to the
OBDII 16-pin connector.
(-) Driver
Door Sense
Trigger*
Diagnostic connector
OBDII (connector side view)
1 8
169
Can HIGH
Tan/Black or Blue: pin 6
Can LOW
Tan or White: pin 14
SW CAN Lt. Green: pin 1
3
1
9: Purple/Green: N.C.
8: Purple/Brown: N.C.
Pink: Ignition Output.
White/Black: N.C.
BA C
Clutch Switch
(black connector)
For manual
transmission
vehicles only.
Yellow
(On the Camaro and Cruze vehicles)
T-Harness
THGM610
(Optional)
6
12
1
7
GM10
GM10
Ignition
Barrel
T-01
T-02
Rev.: 20130304
Platform: DBALL
Firmware: GM10 v. 2.08+
© 2012 Directed. All rights reserved.
Remove the key from the ignition.
Key OUT
OFF
START
IGN
Page 10
Module Programming
Refer to the LED Diagnostics section for more information and for troubleshooting purposes.
Important
Make all the required connections to the vehicle, as described in the wiring diagram(s) found in this guide, and double check to
ensure everything is correct prior to moving onto the next step.
To take advantage of advanced features, you must use XpressVIP 4.5 or higher. Using version 2.9 or 3.1 will limit
available functions and features.
1. Connect the interface module to your computer using the XKLoader2.
2. Open an Internet Explorer browser (version 6 or higher), and go to www.xpresskit.com. The detail of the platform and firmware
that is currently saved on the interface module will be indicated in the top left corner of the page.
3. Select the year, make and model of the vehicle; the page will refresh to display the compatible firmware.
4. In the search result page, select one of the available install options (config for RSR, RXT or Standard install), and follow the
instructions provided on the screen.
5. Once you have configured your options, click on the FLASH button to upload the firmware onto the interface module.
6. The following message will be displayed when the upload is completed:
“The flashing is successfully completed. You may now unplug the kit.”
You can now proceed with the programming instructions below.
Warning!
2
Solid
The LED turns ON solid red.
1
OR
If required for your installation, connect the 10-pin, 12-pin
and 14-pin harnesses to the module, then connect the 4-pin
D2D harness.
D2D Installation
If required for your installation, connect the 10-pin and 12-pin
harnesses to the module, then connect the 14-pin harness to
the module.
W2W Installation
1
0
-
p
i
n
D
2D
st
1
12
-p
i
n
14
-pin
nd
2
rd
3
10
-
p
i
n
D2D
st
1
th
4
1
2-pi
n
1
4
-
p
i
n
nd
2
rd
3
5
4
3
6
Press the Unlock button on the OEM remote and wait until the
LED starts to flash orange.
Make sure the driver’s door is open.
Remove the key from the ignition barrel. The LED will keep flashing green.
Turn the key to the IGN position. The LED will start to flash green.
Steps 5 to 7 must be executed within 5 seconds.
&
&
&
Key IN
OFF
START
I
GN
Key OUT
OFF
START
I
G
N
Flashes
Flashes
Flashes
7
Insert and turn the key back to the IGN position. The LED will
change to solid green for 3 sec. then OFF.
&
Key IN
OFF
START
I
G
N
Solid
Press
Unlock button
Rev.: 20130304
Platform: DBALL
Firmware: GM10 v. 2.08+
© 2012 Directed. All rights reserved.
Page 11
2
Solid
&
Solid
Flashes
&
Release
3
Wait 3 seconds until the LED turns ON solid orange, and wait 10 more seconds
until the LED starts to flash orange and red.
Release the programming button. The LED turns ON solid red.
Warning Against Executing a Hard Reset!
A hard reset will revert the flashed firmware back to its default settings. Depending on the installation, some settings (such
as RFTD and D2D options) may have to be reconfigured. See the Feature & Option List section of this guide.
1
OR
If required for your installation, connect the 10-pin, 12-pin &
14-pin harnesses to the module. Press and hold the
programming button, then connect the 4-pin D2D harness.
D2D Installation
If required for your installation, connect the 10-pin & 12-pin
harnesses to the module. Press and hold the programming
button, then connect the 14-pin harness to the module.
W2W Installation
1
0
-
pi
n
D2
D
st
1
12-p
in
14
-
pin
nd
2
th
4
rd
3
10-
pi
n
D2D
st
1
th
5
1
2-p
i
n
1
4
-pin
nd
2
rd
3
th
4
Module Reset
Hard Reset
2
& &
Solid Solid
Release
Wait 3 seconds until the LED turns ON solid orange then release the
programming button. The LED then turns ON solid red.
A module reset will only erase programming performed in the previous steps. All settings (firmware) and settings flashed
to the module using the web config tool will not be affected.
1
OR
If required for your installation, connect the 10-pin, 12-pin &
14-pin harnesses to the module. Press and hold the
programming button, then connect the 4-pin D2D harness.
D2D Installation
If required for your installation, connect the 10-pin & 12-pin
harnesses to the module. Press and hold the programming
button, then connect the 14-pin harness to the module.
W2W Installation
10
-
p
in
D
2D
st
1
12
-
pi
n
14
-pin
nd
2
th
4
rd
3
10
-
p
in
D2D
st
1
th
5
1
2-p
i
n
14
-
pin
nd
2
rd
3
th
4
Rev.: 20130304
Platform: DBALL
Firmware: GM10 v. 2.08+
© 2012 Directed. All rights reserved.
Page 12
Feature & Option List
It is recommended to configure all the features and options listed below using the configuration tool found on the module flashing page
on www.xpresskit.com. The web offers more options such as EIPS and RSR; however, a manual configuration of the features is
possible using the information on this page.
Feat. Operation Flashes/Option Description
1. No RF Output* Module is connected to a remote starter using a standard installation.
2. RFTD Output Module is connected to an XL202 using an RSR or RXT installation (when available).
3. SmartStart Module is connected to SmartStart using an RSR or RXT installation (when available).
1. Driver priority* Unlocks only the driver door on first press and unlocks all doors on a second press within 5 seconds.
2. All Unlocks all doors on first press.
1. Disabled* N/A
2. Windows Only N/A
3. Windows and sunroof ** N/A
1. Disabled* No operation.
2. Enabled It will activate the Heated Seats Control feature (see feature #5).
1. 32 °F (0 °C)*
When feature #4 is enabled, it will activate the heated seats upon remote start when temperature is below
32 °F (0 °C).
2. 23 °F (-5 °C)
When feature #4 is enabled, it will activate the heated seats upon remote start when temperature is below
23 °F (-5 °C).
3. 41 °F (5 °C)
When feature #4 is enabled, it will activate the heated seats upon remote start when temperature is below
41 °F (5 °C).
4. Always ON When feature #4 is enabled, it will activate the heated seats at any temperature.
1. Disabled* No operation.
2. Ignition Locks all doors when ignition is ON. Unlocks all doors when ignition turns OFF.
3. Brake
Locks all doors when brake pedal is pressed while the vehicle is running. Unlocks all doors when ignition
turns OFF.
4. Speed Locks all doors when the vehicle is moving. Unlocks all doors when ignition turns OFF.
1. Disabled
The OEM alarm will not be controlled by DBALL upon remote start. No disarm or arm command will be
executed at the beginning or end of the sequence; it must be controlled by the Remote Starter.
2. Safelock
Smart OEM Alarm Control will behave like a standard Safelock feature on a remote starter. It will unlock at
the beginning of the sequence, and relock after start and shutdown.
3. Enabled*
Smart OEM Alarm Control will synchronize with the OEM alarm so that it will disarm and rearm the vehicle
in the remote start sequence, only when required. The reason for this is, factory alarm control must often be
done by lock or unlock operation. This could create unnecessary actions on door lock modules, such as the
horn to honk. When possible, Smart OEM Alarm Control will monitor the alarm and door lock status to
detect if the disarm or rearm is required. If the vehicle is unlocked or is not equipped with factory alarm, the
disarm/rearm will not be executed. Smart OEM Alarm Control will also monitor the remote starter actions so
that the factory alarm control is not done twice. A remote starter, for which the Safelock feature is active,
will work perfectly with this option and will make it invisible to the user.
5 Heated Seats Control
4 Heated Seats
** Do not use in vehicles without sunroof
6
* Default Option
Smart OEM Alarm
Control
7
Automatic Controlled
Door Lock
3
Automatic Comfort
Closure with Lock
RFTD Output Type1
Unlock Driver Priority2
Rev.: 20130304
Platform: DBALL
Firmware: GM10 v. 2.08+
© 2012 Directed. All rights reserved.
To enter feature programming routine
Turn the ignition ON, then OFF.
Within 5 seconds, press and HOLD the programming button until the LED turns ON orange (after 3 seconds). Release the
Programming button.
The LED will flash green once slowly to indicate the feature number is 1. After a short delay, the LED flashes red rapidly to indicate
the current option of feature 1 (i.e. 1x green followed by 1x red indicates feature 1 is set to option 1). The flashing sequence will
repeat until a new command is entered.
Accessing another feature
Press and release the programming button a number of times to advance from the current feature to the next desired .
The LED flashes green slowly the number of times equal to the feature number. After a short delay, the LED flashes red rapidly to
indicate the current option of the current feature.
When the maximum number of features or options is reached, the LED will start flashing again from the first feature or
option.
Once a feature is programmed
Other features can be programmed.
The feature programming can be exited.
-
-
-
-
-
-
-
Changing feature options
Press the lock/arm or unlock/disarm button on aftermarket transmitter to change the option of the selected feature.
The LED flashes red rapidly the number of times equal to the current option number. After a short delay, the LED flashes green
slowly the number of times to indicate the current feature.
-
-
The flashing sequence will repeat until a new command is entered.
feature
The flashing sequence will repeat until a new command is entered.
Exiting feature programming
-
sequence.
OR
-
Press and HOLD the programming button for 3 seconds. After 3 seconds, the LED will turn ON for 2 seconds to confirm
.
No activity for 30 seconds; after 30 seconds, the LED will turn ON for 2 seconds to confirm the end of the programming orange
orange the
end of the programming sequence
Feature Programming
Programming
Button
Page 13
Rev.: 20130304
Platform: DBALL
Firmware: GM10 v. 2.08+
© 2012 Directed. All rights reserved.
LED Status Description Troubleshooting
Module Programming
Solid Red Waiting for Can detection.
Make sure that your HSCAN and SWCAN are properly
connected and press Unlock on the OEM remote.
Flashes Orange
CAN and Data Bypass
successfully detected.
Normal operation
Flashes Green Cycle timeout started.
Normal operation. You have now 5 seconds to finish module
programming.
Solid Green 3 seconds
Module successfully
programmed.
Normal operation
Flashes Red 1 time
Data Bypass line sleeping or not
connected.
Press Unlock on the OEM remote to activate the Data Bypass.
Flashes Red 2 times
Failed to completely remove the
key from ignition or turned the
ignition OFF without removing the
key while bypass sequence was
executing.
Cycle (programming steps 5 to 7) was done without removing
the key. Reset module and retry module programming from
step 1.
Flashes Red 3 times
Cycle (programming steps 5 to 7)
timed out.
Cycle (programming steps 5 to 7) was done slower than 5
seconds. Reset module and retry module programming from
step 1.
Flashes Red 4 times
Data Bypass line sleeping or not
connected.
Make sure that your connections to Data Bypass are correct,
remove key, press Unlock on the OEM remote and make sure
that the LED is flashing orange before turning the key to
ignition.
Flashes Red 5 times Programming failed.
Reset the module and retry the module programming from step
1.
Flashes Red 6 times HS CAN not detected.
Flashes Red 7 times SW CAN not detected.
Active Ground While Running
Flashes Green Ground out (GWR) is active. Normal operation
Off Normal operation
The Ground While Running (status) wire is incorrectly
connected. Refer to the wiring diagram to make the right
connections.
Inactive Ground While Running
Flashes Green once Lock function executed.
Flashes Green twice Unlock function executed.
Flashes Green 3 times Trunk release function executed.
If it does not flash, the bypass module did not receive the signal.
Verify the connections between the bypass and the remote
starter module.
Check connections and click Unlock again to activate the line.
LED Diagnostics and Troubleshooting
Flashes
Flashes
Flashes x2
Flashes x1
Flashes x4
Flashes x5
Flashes x6
Flashes x7
Flashes x3
Solid
x3 sec.
Flashes
Solid
Off
Flashes x3
Flashes x2
Flashes x1
Page 14
Rev.: 20130304
Platform: DBALL
Firmware: GM10 v. 2.08+
© 2012 Directed. All rights reserved.
For a period of ONE YEAR from the date of purchase of a Directed Electronics remote start or security product, Directed
Electronics. (“DIRECTED”) promises to the original purchaser, to repair or replace with a comparable reconditioned piece, the
security or remote start accessory piece (hereinafter the “Part”), which proves to be defective in workmanship or material
under normal use, provided the following conditions are met: the Part was purchased from an authorized DIRECTED dealer;
and the Part is returned to DIRECTED, postage prepaid, along with a clear, legible copy of the receipt or bill of sale bearing the
following information: consumer’s name, address, telephone number, the authorized licensed dealer’s name and complete
product and Part description.
This warranty is nontransferable and is automatically void if the Part has been modified or used in a manner contrary to its
intended purpose or the Part has been damaged by accident, unreasonable use, neglect, improper service, installation or
other causes not arising out of defect in materials or construction.
TO THE MAXIMUM EXTENT ALLOWED BY LAW, EXCEPT AS STATED ABOVE, ALL WARRANTIES, INCLUDING BUT NOT
LIMITED TO EXPRESS WARRANTY, IMPLIED WARRANTY, WARRANTY OF MERCHANTABILITY, FITNESS FOR
PARTICULAR PURPOSE AND WARRANTY OF NONINFRINGEMENT OF INTELLECTUAL PROPERTY, ARE EXPRESSLY
EXCLUDED; AND DIRECTED NEITHER ASSUMES NOR AUTHORIZES ANY PERSON OR ENTITY TO ASSUME FOR IT
ANY DUTY, OBLIGATION OR LIABILITY IN CONNECTION WITH ITS PRODUCTS. DIRECTED HEREBY DISCLAIMS AND
HAS ABSOLUTELY NO LIABILITY FOR ANY AND ALL ACTS OF THIRD PARTIES INCLUDING DEALERS OR
INSTALLERS. IN THE EVENT OF A CLAIM OR A DISPUTE INVOLVING DIRECTED OR ITS SUBSIDIARY, THE PROPER
VENUE SHALL BE SAN DIEGO COUNTY IN THE STATE OF CALIFORNIA. CALIFORNIA STATE LAWS AND APPLICABLE
FEDERAL LAWS SHALL APPLY AND GOVERN THE DISPUTE. THE MAXIMUM RECOVERY UNDER ANY CLAIM
AGAINST DIRECTED SHALL BE STRICTLY LIMITED TO THE AUTHORIZED DIRECTED DEALER’S PURCHASE PRICE
OF THE PART. DIRECTED SHALL NOT BE RESPONSIBLE FOR ANY DAMAGES WHATSOEVER, INCLUDING BUT NOT
LIMITED TO, ANY CONSEQUENTIAL DAMAGES, INCIDENTAL DAMAGES, DAMAGES FOR THE LOSS OF TIME, LOSS
OF EARNINGS, COMMERCIAL LOSS, LOSS OF ECONOMIC OPPORTUNITY AND THE LIKE. NOTWITHSTANDING THE
ABOVE, THE MANUFACTURER DOES OFFER A LIMITED WARRANTY TO REPLACE OR
REPAIR AT DIRECTED’S OPTION THE PART AS DESCRIBED ABOVE.
Some states do not allow limitations on how long an implied warranty will last or the exclusion or limitation of incidental or
consequential damages. This warranty gives you specific legal rights and you may also have other rights that vary from State
to State. DIRECTED does not and has not authorized any person or entity to create for it any other obligation, promise, duty or
obligation in connection with this Part.
920-0007 2009-09
This Interface kit / Data Bus Interface part has been tested on the listed vehicles. Other vehicles will be added to the select
vehicle list upon completion of compatibility testing. Visit website for latest vehicle application guide. DISCLAIMER: Under no
circumstances shall the manufacturer or the distributors of the bypass kit / data bus interface part(s) be held liable for any
consequential damages sustained in connection with the part(s) installation. The manufacturer and it’s distributors will not, nor
will they authorize any representative or any other individual to assume obligation or liability in relation to the interface kit / data
bus interface part(s) other than its replacement. N.B.: Under no circumstances shall the manufacturer and distributors of this
product be liable for consequential damages sustained in connection with this product and neither assumes nor authorizes
any representative or other person to assume for it any obligation or liability other than the replacement of this product only.
Protected by U.S. Patents: 5,719,551; 6,011,460 B1 *; 6,243,004 B1; 6,249,216 B1; 6,275,147 B1; 6,297,731 B1; 6,346,876
B1; 6,392,534 B1; 6,529,124 B2; 6,696,927 B2; 6,756,885 B1; 6,756,886 B2; 6,771,167 B1; 6,812,829 B1; 6,924,750 B1;
7,010,402 B1; 7,015,830 B1; 7,031,826 B1; 7,046,126 B1; 7,061,137 B1; 7,068,153 B1; 7,205,679 B1; Cdn. Patent:
2,320,248; 2,414,991; 2,415,011; 2,415,023; 2,415,027; 2,415,038; 2,415,041; 2,420,947; 2,426,670; 2,454,089; European
Patent: 1,053,128; Pat. Pending: 2,291,306. Made in Canada.
Limited One Year Consumer Warranty
Additional information can be found at:
www.xpresskit.com
www.directechs.com
Page 15
Rev.: 20130304
Platform: DBALL
Firmware: GM10 v. 2.08+
© 2012 Directed. All rights reserved.
Rev.: 20130304
Quick Reference Guide
DBALL-GM10
© 2012 Directed. All rights reserved.
Button(s)
Actions
Press & hold for 1 second to lock.
Press & hold for 1 second to unlock.
Press & hold for 1 second to remote
start.
Press & hold for 5 seconds to activate
the trunk release (optional).
Press once, then to activate the
rear hatch/tail glass release (optional).*
Press 3 times, then to activate
the panic mode.
Press once, then to reset the
remote starter runtime.
List of Available Commands
x1 +
x3 +
x1 +
* This output is configurable. see your authorized installation center for more
information.
Note that the information below is for Viper, Clifford and Python models. Icons and
commands may differ depending on the remote brand and model purchased. Refer
to your authorized installation center for more information.
Additional Features
(Must be completed by the installer.)
Note: Additional fees may apply for the installation of the above features.
Trunk
The following features are available with this product, but may not be compatible
with your vehicle. Refer to your installation facility for more information.
Heated Seats Feature
Heated Seats will start automatically at _________________ level if the ambiant
temperature is below _________°F (_________°C).
Even if Heated Seats Temperature Control is set to start below a specific
temperature, you can remote activate heated seats manually with your
aftermarket remote by pressing AUX3 button(s). Available only if your vehicle is
running by remote starter.
Notes
? L ?? A?
G ? ? ? ? w? ?
W? ? T? ? ? ? ? T
A D S I ? ? ? ?
Hyundai Genesis Sedan with Smart Key
©2010DirectedElectronics.Allrightsreserved.
("Push-button Start")
Hyundai proximity key solution
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16

Directed DBALL-GM10 XPRESSKIT Quick Reference Manual

Directed
Brand
Directed
Model
DBALL-GM10 XPRESSKIT
Category
Remote starters
Type
Quick Reference Manual
Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents