2. LAMONA
  3. LAM8304
LAM8304

LAMONA LAM8304 Owner's manual

  • Hello! I am an AI chatbot trained to assist you with the LAMONA LAM8304 Owner's manual. I’ve already reviewed the document and can help you find the information you need or explain it in simple terms. Just ask your questions, and providing more details will help me assist you more effectively!
Generic instructions, (To be used in conjunction with User Instructions).
lPlease read this Installation Manual to ensure safe fitting and use of the appliance.
lThe appliance should be fitted by a suitably competent and qualified person.
lPlease keep these instructions in a safe place for future reference.
lDanger of suffocation keep packaging material away from children.
Installation Instructions
LAM8304
www.howdens.com/appliance-registration
Built-In Dishwasher
3
Exclusive to Howdens
Risk of damage to
appliance:
Do not attempt to
move the appliance
by the door.
NOTE: Do not leave the
dishwasher door open.
Be careful not to trip
over open door.
Warning:
Be aware of the
instability of the
appliance prior to being
fitted into position.
Risk of damage to
property:
Take care of
surrounding area when
moving the appliance
to prevent damage to
flooring, wall coverings,
pipes etc..
Two person lift. Risk of injury:
Beware of sharp metal
edges. Use gloves when
handling.
NOTE: If the electricity
cable is damaged it
must be replaced by a
competent person.
Dishwasher must
be fixed securely and
level.
Ensure that all packing
and transit protectors
have been removed
from the appliance
before positioning.
Do Not install a
damaged machine.
Safety Information
Warning for injury or
property damage risk.
Warning for electric shock. Warning for risk of
fire / flammable materials.
Throughout this manual the following symbols are used.
DO NOT KINK HOSES
BEHIND MACHINE!
Machine will not work properly.
Cancel
3 sec.
F1
F2
F3
F4
or machine does not fill / empty -
CHECK HOSES for kinks.
If after installation upon 1st use an
error code is displayed,
4www.howdens.com
Installation overview guide
Safety Information (continued)
1. Dimensions .........................................................................p.6
2. Dishwasher connections. ...........................................p.6
3. Fit feet and raise 10-15mm below
worktop height .................................................................. p.8
4. Locate securing brackets ...........................................p.8
5. Protection strip for timber worktops .....................p.9
6. Positioning the dishwasher .......................................p.9
7. Adjust feet and raise dishwasher to
underside of worktop (level) .....................................p.10
8. Remove ‘H’ frame.............................................................p.10
9. Standard decor door preparation .........................p.11
10. Decor drawer frontals preparation .......................p.11
11. Fit decor door / decor drawer frontals ................p.12
12. Final adjustment and secure dishwasher .........p.13
13. Fit plinth ................................................................................p.14
14. Connect water/plumbing/electric...........................p.14
15. Profile Kitchen ...................................................................p.15
Electrical connection
WARNING! Risk of fire and electric shock.
• The appliance must be earthed.
• Make sure that the electrical information on the
rating plate agrees with the power supply. If not,
contact an electrician.
• Do not use multi-plug adapters and extension
cables.
• Avoid damage to the mains plug and mains cable.
Should the mains cable need to be replaced,
contact a LAMONA Authorised Service Agent or a
suitably qualified person.
• Connect the mains plug only at the end of the
installation. Ensure access to the mains plug after
the installation.
• This appliance complies with all relevant
E.U. Directives.
• The appliance has a 13amp plug.
Use fuse: 13amp ASTA (BS 1362).
Water connection (cold water supply)
• Do not kink or damage the hoses during installation.
• Before you connect the fill hose to the appliance;
let some water flow through to ensure all debris is
removed.
• We suggest you connect the fill hose and open
the water valve before pushing the appliance into
position.
• Check for leaks during and after installation and
after first use.
• If the water inlet hose is damaged, immediately
close the water supply valve and disconnect the
mains plug from the mains socket.
• The appliance is to be connected to the water
mains using the new hose-set supplied with the
appliance. Do not re-use old hose-sets.
5
Exclusive to Howdens
Phillips head
Flat head
Torx head
10mm open
ended spanner
x1x1
A (3.5x14)x1x1 x4
+50mm
C (4x36mm)
Phillips head
B (4x43mm)
Phillips head
DO NOT use high
speed impact
power tools.
Installation
Parts supplied
Tools required
6www.howdens.com
min
15mm
818mm
(+100)
550mm 448mm
820-920mm
min
570mm
*450mm (+1)
min
500mm
min
300mm
max
1000mm
*max.
100mm
*
min
500mm
min
300mm
max
1000mm
1 - Dimensions
2 - Dishwasher connections
Position the dishwasher
relative to service connections.
All dimensions are to the floor. DO NOT insert the hose too deep into the waste pipe,
(Maximum hose length, 3.2 metres).
*If niche is wider than 450mm,
place packers at screw fixing points between
dishwasher and cabinet sides.
7
Exclusive to Howdens
Cold water supply
10-80 lpm.
REMOVE
CAP/END
WARNING! This appliance
must be earthed.
(Socket must be accessible
after fitting).
WARNING! Do not use extension
cables / adapters.
Ensure water is turned on and
the isolator valve is accessible
after fitting.
Hose connection - 3/4”.
Cold water pressure -
0.1 – 1Mpa (0.3 - 1.0 Bar)
Incorrect waste pipe configuration. Correct waste pipe configuration.
Ensure cap/end is removed from
waste pipe spigot.
NOTE: Ensure hoses are not
kinked or trapped behind
the dishwasher.
NOTE: If necessary loosen and
rotate the water hose towards
the water supply and re-tighten.
(Always use the new hose supplied
with the dishwasher).
NOTE: Issues with hoses or drain will cause machine to malfunction.
8www.howdens.com
DO NOT use high speed
impact power tools.
DO NOT damage the
plastic screw heads.
+_
10-15mm
+
_
Plus foot
addition
+50mm
Foot,
max
50mm
For standard installation extension
feet need to be fitted.
Do not position
in cabinet run at
this stage.
3 - Fit feet and raise to 10-15mm below worktop height
Front feet Rear feet
4 - Locate securing brackets
Insert brackets and fold.
Do not flatten bracket tab
with hammer.
Insert brackets and fold.
Do not flatten bracket tab
with hammer.
9
Exclusive to Howdens
&
5 - Protection strip for timber worktops to avoid condensation damage
Ensure a clean and
dust free surface. Cut to fit.
NOTE: This strip must be fitted to timber worktops to
avoid damage. Ensure protection strip is set to edge
of square edged worktops.
6 - Positioning the dishwasher
Push back
and pull hoses
through.
NOTE: Ensure hoses are
not kinked or trapped
behind the dishwasher.
NOTE: If necessary
loosen and rotate the
water hose towards the
water supply and re-
tighten.
Always use the new
hose supplied with the
dishwasher.
10 www.howdens.com
DO NOT use high speed
impact power tools.
DO NOT damage the
plastic screw heads.
+_
+
Flat head
screw driver
_
Plumb & level
(touch at
front)
7 - Adjust feet and raise dishwasher to underside of worktop (level)
8 - Remove ‘H’ frame
Retain for
stage 9/10.
Front feet
Rear feet
It is critical that
the dishwasher is
installed level.
11
Exclusive to Howdens
A (3.5x14) x2
Stage 8 screws x2
A (3.5x14) x2
Stage 8 screws x2
=
=
TOP
Centre line
267mm 517mm
192mm
192mm
60mm
130mm
130mm
=
267mm
517mm
2 x 356mm drawer fronts = 712mm
Normal door height = 716mm
Therefore space between
drawer fronts = 3-4mm
TOP
Centre
=
192mm
192mm
9 - Standard decor door preparation
10 - Decor drawer frontals preparation
Remove centre rail.
12 www.howdens.com
2mm
B (4x43mm)
Phillips head 43mm
numbers 3 and 6.
2mm
B (6x43mm)
Phillips head 43mm
numbers 3, 4 and 6.
11 - Fit decor door / decor drawer frontals
2
1
34
5
6
123
4
5
6
Fixing for standard decor door
DO NOT use hole 1, especially
when fitting an integrated
handle decor door.
If necessary make final alignment
and fully tighten the screws. Make
sure screws are fastened flush.
DO NOT over-tighten.
Fixing for decor drawer frontals
12
345
6
2
1
3
4
5
6
13
Exclusive to Howdens
A (3.5x14) x4 A (3.5x14) x4
3mm3mm
450mm (+1) 451mm (+>1)
Avoid
screwhead
clash
2mm
Ensure screw
does not clash
with decor door!
C (4x36mm) x2
Phillips head
12 - Final adjustment and secure dishwasher
Maximum 450mm (+1)
Solid worktop Timber worktop
It is critical that the
dishwasher is installed
level.
Side fixing for solid
surface worktops and
top fixing for timber
worktops.
Securing screws
Use packers if niche is >450mm
Do not bow dishwasher sides.
Do not
overtighten
14 www.howdens.com
Cold water supply
10-80 L/pm.
Cancel
3 sec.
F1
F2
F3
F4
13 - Fit plinth
14 - Switch on water and electric
Once decor door / decor drawer
frontals are fitted correctly, fit the
plinth.
Final checks:
Decor door opens and
closes without clash?
Dishwasher installed level
Front Rear,
Side Side?
Hoses not kinked?
Run a programme cycle to confirm successful installation
and that there are no leaks.
If during initial use the machine
does not fill / empty.
Check hoses,
see ‘Dishwasher connections’.
15 - Profile Kitchen
Pre-install an infill when fitting a dishwasher into a Profile Kitchen.
It is critical that
the dishwasher is
installed level.
18mm infill
Apply moisture barrier tape.
Product serial number
(Place sticker here)
Product information correct at the time of publication in November 2020.
The company has a policy of continuous product development and reserves the
right to change any products and specifications given in this manual. Subject to
the Terms and Conditions of Trading, a copy of the Howdens Terms and Conditions
is available upon request.
Copyright © 2020 Howden Joinery Ltd. All rights reserved.
ISSUE v1 011120
/