Generic instructions, (To be used in conjunction with User Instructions).
l Please read this Installation Manual to ensure safe fitting and use of the appliance.
l The appliance should be fitted by a suitably competent and qualified person.
l Please keep these instructions in a safe place for future reference.
l Danger of suffocation keep packaging material away from children.
Installation Instructions
www.howdens.com/appliance-registration
Built-In Dishwasher
LAM8676
LAM8607
ISSUE v1.4
3
Exclusive to Howdens
Risk of damage to
appliance:
Do not attempt to
move the appliance
by the door.
NOTE: Do not leave the
dishwasher door open.
Be careful not to trip
over open door.
Warning:
Be aware of the
instability of the
appliance prior to being
fitted into position.
Risk of damage to
property:
Take care of
surrounding area when
moving the appliance
to prevent damage to
flooring, wall coverings,
pipes etc..
Two person lift. Risk of injury:
Beware of sharp metal
edges. Use gloves when
handling.
NOTE: If the electricity
cable is damaged it
must be replaced by a
competent person.
Dishwasher must
be fixed securely and
level.
Ensure that all packing
and transit protectors
have been removed
from the appliance
before positioning.
Do Not install a
damaged machine.
70
°
C
60
°
C
eco
50
°
C
40-65
°
C
AUTO
30
°
C
mix 40
°
C
Cancel 3 sec.
hygiene
Safety Information
Warning for injury or
property damage risk.
Warning for electric shock. Warning for risk of
fire / flammable materials.
Throughout this manual the following symbols are used.
DO NOT KINK HOSES
BEHIND MACHINE!
Machine will not work properly.
70
°C
60
°C
eco
50
°C
40-65
°C
AUTO
30
°C
mix 40
°C
Cancel 3 sec.
hygiene
or machine does not fill / empty -
CHECK HOSES for kinks.
If after installation upon 1st use an
error code is displayed,
4
www.howdens.com
1. Dimensions .........................................................................p.6
2. Dishwasher connections. ...........................................p.6
3. Fit feet and raise 10-15mm below
worktop height .................................................................. p.8
4. Profile kitchen ....................................................................p.8
5. Protection strip for timber worktops .....................p.9
6. Positioning the dishwasher .......................................p.9
7. Adjust feet and raise dishwasher to
underside of worktop (level) .....................................p.10
8. Remove ‘H’ frame.............................................................p.10
9. Standard decor door preparation .........................p.11
10. Decor drawer frontals preparation .......................p.11
11. Fit decor door / decor drawer frontals ................p.12
12. Final adjustment and secure dishwasher .........p.13
13. Fit plinth ................................................................................p.14
14. Connect water/plumbing/electric...........................p.14
Installation overview guide
Safety Information (continued)
Electrical connection
WARNING! Risk of fire and electric shock.
• The appliance must be earthed.
• Make sure that the electrical information on the
rating plate agrees with the power supply. If not,
contact an electrician.
• Do not use multi-plug adapters and extension
cables.
• Avoid damage to the mains plug and mains cable.
Should the mains cable need to be replaced,
contact a LAMONA Authorised Service Agent or a
suitably qualified person.
• Connect the mains plug only at the end of the
installation. Ensure access to the mains plug after
the installation.
• This appliance complies with all relevant
E.U. Directives.
• The appliance has a 13amp plug.
Use fuse: 13amp ASTA (BS 1362).
Water connection (cold water supply)
• Do not kink or damage the hoses during installation.
• Before you connect the fill hose to the appliance;
let some water flow through to ensure all debris is
removed.
• We suggest you connect the fill hose and open
the water valve before pushing the appliance into
position.
• Check for leaks during and after installation and
after first use.
• If the water inlet hose is damaged, immediately
close the water supply valve and disconnect the
mains plug from the mains socket.
• The appliance is to be connected to the water
mains using the new hose-set supplied with the
appliance. Do not re-use old hose-sets.
5
Exclusive to Howdens
Phillips head
Flat head
Torx head
10mm open
ended spanner
DO NOT use high
speed impact
power tools.
x1x1 x4
+50mm
(4x36mm)
Phillips head Side Spacer
(4x42mm)
Phillips head
(4x13mm)
x6 x6 x4
Phillips head
x4
ABC
Installation
Parts supplied
Tools required
6
www.howdens.com
min
500mm
min
300mm
max
1000mm
*max.
100mm
*
min
500mm
min
300mm
max
1000mm
min
15mm
818mm
(+100)
550mm 598mm
820-920mm
min
570mm
*600mm (+1)
1 - Dimensions
2 - Dishwasher connections
Position the dishwasher
relative to service connections.
For Profile Kitchens,
see section 4.
All dimensions are to the floor. *DO NOT insert the hose too deep into the waste pipe,
(Maximum hose length, 3.2 metres).
Fit and adjust the spacers to the niche width.
(both sides - see page 9)
Cabinet
Dishwasher
Adjust the spacer to fill
the gap between the
dishwasher and the cabinet
Dishwasher
7
Exclusive to Howdens
Cold water supply
10-80 lpm.
REMOVE
CAP/END
WARNING! This appliance
must be earthed.
(Socket must be accessible
after fitting).
WARNING! Do not use extension
cables / adapters.
Ensure water is turned on and
the isolator valve is accessible
after fitting.
Hose connection - 3/4”.
Cold water pressure -
0.1 – 1Mpa (0.3 - 1.0 Bar)
Incorrect waste pipe configuration. Correct waste pipe configuration to avoid water flow
from the sink to dishwasher
Ensure cap/end is removed
from waste pipe spigot.
NOTE: Ensure hoses are not
kinked or trapped behind
the dishwasher.
NOTE: If necessary loosen and
rotate the water hose towards
the water supply and re-tighten.
(Always use the new hose supplied
with the dishwasher).
NOTE: Issues with hoses or drain will cause machine to malfunction.
8
www.howdens.com
DO NOT use high speed
impact power tools.
DO NOT damage the
plastic screw heads.
+
Flat head
screw driver
_
+_
Plus foot
addition
+50mm
Foot,
max
50mm
10-15mm
x2 x2
For standard installation,
extension feet need to
be fitted.
3 - Fit feet and raise to 10-15mm below worktop height
Front feet
Rear feet
4 - Profile kitchen
Do not position
in cabinet run at
this stage.
Pre-install an infill when fitting a dishwasher into a Profile Kitchen.
It is critical that
the dishwasher is
installed level.
RKC0071 x2
Apply moisture barrier tape.
9
Exclusive to Howdens
&
NOTE: Ensure hoses
are not kinked or
trapped behind the
dishwasher.
5 - Protection strip for timber worktops to avoid condensation damage
6 - Positioning the dishwasher
NOTE: If necessary loosen and
rotate the water hose towards
the water supply and re-tighten.
Always use the new hose
supplied with the dishwasher.
Ensure a clean and
dust free surface. Cut to fit.
NOTE: This strip must be fitted to timber worktops to
avoid damage. Ensure protection strip is set to edge
of square edged worktops.
Push machine
back and pull
hoses through.
Set the desired width
Adjust side
spacer fixings
10
www.howdens.com
DO NOT use high speed
impact power tools.
DO NOT damage the
plastic screw heads.
+_
Plumb & level
(touch at
front)
+
Flat head
screw driver
_
7 - Adjust feet and raise dishwasher to underside of worktop (level).
Front feet
8 - Remove ‘H’ frame for frontal fitting
Rear feet
Retain screws for
stage 9/10.
It is critical that the dishwasher is
installed level.
11
Exclusive to Howdens
(4x13) x2
Stage 8 screws x2
A
(4x13) x2
Stage 8 screws x2
A
=
=
TOP
Centre line 267mm 517mm
267mm
267mm
60mm
130mm
130mm
=
267mm
2 x 356mm drawer fronts = 712mm
Normal door height = 716mm
Therefore space between
drawer fronts = 3-4mm
TOP
Centre Line
=
517mm
267mm
267mm
9 - Standard decor door preparation
10 - Decor drawer frontals preparation
Remove centre rail.
12
www.howdens.com
(4x42mm)
Phillips head 42mm
numbers 3 and 6.
(4x42mm)
Phillips head 42mm
numbers 3, 4 and 6.
B
B
2mm
2mm
11 - Fit decor door / decor drawer frontals
Fixing for standard decor door
DO NOT use hole 1, especially
when fitting an integrated
handle decor door.
12
3
45
6
2
1
3
4
56
12
345
6
2
1
3
4
5
6
Fixing for decor drawer frontals
If necessary make final alignment
and fully tighten the screws.
Make sure screws are fastened flush.
DO NOT over-tighten.
13
Exclusive to Howdens
600mm (+1) 601mm (+>1)
3mm3mm
2mm
Cabinet
Dishwasher
Adjust the spacer to fill
the gap between the
dishwasher and the cabinet
Dishwasher
C
(4x36mm) x4
12 - Final adjustment and secure dishwasher
Securing screws x4 positions
Maximum 600mm (+1)
Do not bow dishwasher sides.
Make sure the spacer is bridging
any gap between the appliance and
the cabinet..
It is critical that the dishwasher is installed level.
Side fixing method for dishwashers
Do not overtighten
14
www.howdens.com
Cold water supply
10-80 L/pm.
70
°C
60
°C
eco
50
°C
40-65
°C
AUTO
30
°C
mix 40
°C
Cancel 3 sec.
hygiene
70
°C
60
°C
eco
50
°C
40-65
°C
AUTO
30
°C
mix 40
°C
Cancel 3 sec.
hygiene
13 - Fit plinth
14 - Switch on water and electric
Once decor door / decor drawer
frontals are fitted correctly, fit the
plinth.
Final checks:
Decor door opens and
closes without clash?
Dishwasher installed level
Front Rear,
Side Side?
Hoses not kinked?
Run a programme cycle to confirm successful installation
and that there are no leaks.
If during initial use the machine
does not fill / empty.
Check hoses,
see ‘Dishwasher connections’.
15
Exclusive to Howdens
Product serial number
(Place sticker here)
Product information correct at the time of publication in October 2023.
The company has a policy of continuous product development and reserves the
right to change any products and specifications given in this manual. Subject to
the Terms and Conditions of Trading, a copy of the Howdens Terms and Conditions
is available upon request.
Copyright © 2023 Howden Joinery Ltd. All rights reserved. HD329092
/