LAM8302
Installation Instructions
Dishwasher
(To be used in conjunction with User Instructions)
Warning for hazardous
situations with regard
to life and property.
Warning for
electric shock.
Throughout this manual the
following symbols are used.
2
Two person lift.
Risk of damage to appliance:
Do not attempt to move the
appliance by the door.
Dishwasher must be xed
securely and level.
Risk of damage to property:
Take care of surrounding area
when moving the appliance to
prevent damage to ooring,
wall coverings, pipes etc..
NOTE: If the electricity cable
is damaged it must be
replaced by a competent
person.
This appliance is not
designed for stacking with
any other appliance.
Warning:
Be aware of the instability of
the appliance prior to being
tted into position.
Ensure that all packing and
transit protectors have been
removed from the dishwasher
before positioning.
Risk of injury:
Beware of sharp metal edges.
Use gloves when handling.
NOTE: Do not leave the
dishwasher door open.
Be careful not to trip over
open door.
www.howdens.com
Introduction
Safety Information
• Please read the Installation Instructions to ensure
safe tting and use of the appliance.
• The dishwasher should be tted by a suitably
competent and qualied person.
• Please keep these instructions in a safe place for
future reference.
3
x1x1
x1x1
x4
+50mm
24mm open
ended spanner
T20, at and
cross head
screw drivers
DO NOT use high
speed impact
power tools.
Sealant
Spacer x2
B (4x43mm) A (3.5x14)
www.howdens.com
Installation
Copyright © 2016 Howden Joinery Ltd. All rights reserved.
Parts supplied
Tools required
4
min
15mm
118mm
44mm
160mm
818mm
(+100)
100mm
(+100)
550mm
448mm
820-920mm
min
570mm
min
450mm
818mm
(+100)
min
570mm
min
450mm
*HJ Kitchen Installation Manual
(*nominal 890mm)
Plus foot
addition
+50mm
Foot,
max
50mm
www.howdens.com
1 - Dimensions
Position the dishwasher relative to service connections.
2 - Opening height
Opening height from the oor to the underside of the
worktop is between 820mm - 920mm.
For standard installation
extension feet need to
be tted.
5
DO NOT use high speed
impact power tools.
DO NOT damage the
plastic screw heads.
_
+
Final height adjustment
may be required after
positioning of the
dishwasher.
+
_
24mm
T20
=
=
TOP
Centre line
267mm
www.howdens.com
3 - Height adjustment
Front feet Rear feet
4a - Décor door - ‘H’ frame set-up
6
Cross head
A (3.5x14) x2
A (3.5x14) x4
www.howdens.com
4b - Décor door
Unscrew the two screws and remove the plastic ‘H’ bracket.
Retain the screws for stage 4c.
4c - Décor door
Secure with the screws retained from stage 4b plus
two additional screws from the accessory bag.
Fit handles at this stage, if required,
(screws may need countersinking).
7
2mm
B (4x43mm) x4
www.howdens.com
4d - Décor door
Remove the existing xings and using the 43mm
screws supplied, secure at positions 2 and 5.
Ensure correct alignment with the top of the door,
(2mm overlap at top).
DO NOT use hole 1,
especially when tting
an integrated handle
décor door.
DO NOT fully tighten the
screws at this stage.
1
2
3
4
5
1
2
3
4
5
4e - Décor door
If necessary make nal alignment and fully
tighten the screws.
Make sure
screws are
fastened ush
but do not over-
tighten.
8
A (3.5x14) x4
Cross head
A (3.5x14) x2
60mm
130mm
130mm
=
267mm
2 x 356mm drawer fronts = 712mm
Normal door height = 716mm
Therefore space between drawer fronts = 3-4mm
TOP
Centre
=
www.howdens.com
5a - Décor drawers frontal - ‘H’ frame set-up
5b - Décor drawers frontal
Unscrew the two screws and remove the plastic ‘H’ bracket.
Retain the screws for stage 5b.
Secure with the screws retained from stage 5a plus
two additional screws from the accessory bag.
9
2mm
B (4x43mm) x6
www.howdens.com
5c - Décor drawers frontal
Remove centre rail.
5d - Décor drawers frontal
Remove the existing xings and using the 43mm
screws supplied, secure at positions 2, 3 and 5.
Ensure correct alignment with the top of the door,
(2mm overlap at top).
DO NOT use hole 1,
especially when tting
an integrated handle
décor door.
DO NOT fully tighten the
screws at this stage.
1
2
3
4
5
1
2
3
4
5
10
www.howdens.com
6 - Balanced appliance door
If the appliance door needs balancing follow the
steps in stage 7.
When balanced the appliance door holds at 45°.
45°
5e - Décor drawers frontal
If necessary make nal alignment and fully
tighten the screws.
Make sure
screws are
fastened ush
but do not over-
tighten.
11
±
kg
T20
Minus (
_
) kg
Plus (
+
) kg
100mm
100mm
www.howdens.com
8 - Spacers
7 - Balanced appliance door adjustment
12
www.howdens.com
10 - Locate securing brackets
9 - Worktop protection strip
Ensure a clean and
dust free surface.
NOTE: This strip must be tted to avoid
damage to the worktop.
Ensure tape is set to edge of square edged
worktops.
Fold and insert brackets according to worktop material.
13
www.howdens.com
NOTE: Ensure hoses are not kinked
or trapped behind the dishwasher.
NOTE: If necessary loosen and rotate the water hose
towards the water supply and re-tighten.
Always use the new hose supplied with the dishwasher.
11 - Positioning appliance
14
DO NOT use
high speed
impact power
tools.
A (3.5x14) x4 A (3.5x14) x4
www.howdens.com
12 - Securing appliance
Adjust height so that the dishwasher touches the underside of the worktop by adjusting front and rear feet.
Then secure using screws provided, (side xing for solid worktops and top xing for wooden worktops).
Solid worktop Timber worktop
If necessary re-align décor door / drawer frontals
before nally securing.
Make sure
screws are
fastened ush
but do not over-
tighten.
15
max.
100mm
min
500mm
min
300mm
max
1000mm
min
500mm
min
300mm
max
1000mm
www.howdens.com
All dimensions are to
the oor.
DO NOT insert the
hose too deep into
the waste pipe.
Maximum hose
length, 4 metres.
13 - Connecting appliance
16
REMOVE CAP
www.howdens.com
WARNING! This appliance must be earthed.
Socket must be accessible after tting.
Ensure cap / top is removed from waste pipe.
WARNING! Do not use extension cables / adapters.
Ensure water is turned on and the isolator valve is
accessible after tting. Hose connection - 3/4”.
Cold water pressure - 0.03Mpa – 1Mpa (0.3 - 1.0 Bar)
NOTE: Ensure hoses are not kinked or trapped
behind the dishwasher.
NOTE: If necessary loosen and rotate the water hose
towards the water supply and re-tighten. Always use
the new hose supplied with the dishwasher.
13 - Connecting appliance - continued
17
Apply sealant
www.howdens.com
Incorrect waste pipe conguration. Correct waste pipe conguration.
After connecting and running a test program check all connections for leaks.
14 - Trim plinth to suit
Once décor door / drawer frontals are tted correctly, trim plinth to suit.
18
www.howdens.com
Notes
19
www.howdens.com
MAKING SPACE MORE VALUABLE
Product information correct at the time of publication in July 2016. The company has a policy of
continuous product development and reserves the right to change any products and specications
given in this manual. Subject to the Terms and Conditions of Trading, a copy of the Howdens Joinery
Terms and Conditions is available upon request.
Howden Joinery Ltd, First Floor, 40 Portman Square, London, W1H 6LT.
Registered in England 526923
611111AA
/
