Honeywell 2AL7Q-D1 Kinetic Door Contact User manual

Type
User manual

Honeywell 2AL7Q-D1 Kinetic Door Contact is a wireless door/window sensor that can be paired with a compatible controller to trigger actions like turning on lights when a door or window is opened or closed. It is self-powered, has a working frequency of 433MHz, and a control distance of up to 80m outdoors and 30m indoors. The device has a long lifespan of over 100,000 operations and is easy to install with double-sided tape or screws. It is also FCC compliant and meets general RF exposure requirements.

Honeywell 2AL7Q-D1 Kinetic Door Contact is a wireless door/window sensor that can be paired with a compatible controller to trigger actions like turning on lights when a door or window is opened or closed. It is self-powered, has a working frequency of 433MHz, and a control distance of up to 80m outdoors and 30m indoors. The device has a long lifespan of over 100,000 operations and is easy to install with double-sided tape or screws. It is also FCC compliant and meets general RF exposure requirements.

This kinetic door contact could be paired with controller
and installed on the door or window to turn on /o ffthe
light once open or close it.
Product Parameters
Power Supply: Self-powered(No battery)
Working Frequency: 433MHz
Working Temperature: -20°C~+55°C
Control Distance: 80m (outdoor) 30m (indoor)
Life time: >100,000 times
Dimension: 109*27*17 mm
INSTRUCTIONS
Kinetic Door Contact
Product Description Installation Paring with controller
1.Remove the double-sided tap on the back
2.Fix the door contact on selected door.
Do not attach to metal security doors as this may affect
signal transmission.
1.Press pairing button on receiver for around 3 seconds
until the indicator light blinks slowly
2.Open/close the door quickly. Pairing will be successful
if the indicator light stops blinking.
Optional fixing kit
You can mount the door contact with the fixing kit,which
can be screwed on the door. Note: it’s optional.
Screw hole
FCC Warning
This device complies with part 15 of the FCC Rules.
Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and
(2) this device must accept any interference received,
including interference that may cause undesired operation.
Note: This equipment has been tested and found to comply
with the limits for a Class B digital device, pursuant to part
15 of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference in a
residential installation. This equipment generates, uses and
can radiate radio frequency energy and, if not installed and
used in accordance with the instructions,may cause harmful
interference to radio communications. However, there is no
guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful
interference to radio or television reception, which can be
determined by turning the equipment off and on, the user
is encouraged to try to correct the interference by one or
more of the following
receiver.
—Connect the equipment into an outlet on a circuit different
from that to which the receiver is connected.
—Consult the dealer or an experienced radio/TV technician
for help.
Measures
—Reorient or relocate the receiving antenna.
—Increase the separation between the equipment and
FCC ID : 2AL7Q-D1
FCC ID : 2AL7Q-D1
Note: The Grantee is not responsible for any changes or
modifications not expressly approved by the party
responsible for compliance. such modifications could void
the user's authority to operate the equipment
The device has been evaluated to meet general RF
exposure requirement.
To maintain compliance with FCC's RF exposure
guidelines, the distance must be at least 20 cm
between the radiator and your body, and fully supported by
the operating and installation
  • Page 1 1

Honeywell 2AL7Q-D1 Kinetic Door Contact User manual

Type
User manual

Honeywell 2AL7Q-D1 Kinetic Door Contact is a wireless door/window sensor that can be paired with a compatible controller to trigger actions like turning on lights when a door or window is opened or closed. It is self-powered, has a working frequency of 433MHz, and a control distance of up to 80m outdoors and 30m indoors. The device has a long lifespan of over 100,000 operations and is easy to install with double-sided tape or screws. It is also FCC compliant and meets general RF exposure requirements.

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI