IS-52277-US
We’re here to help 866-558-5706
Hrs: M-F 9am to 5pm EST
1) Pass xture wire from main frame[K] through decorave nut cover[N] and
through large loop[J].
2) Slip decorave nut cover over protruding threads and hexnut on top of main
frame.
3) Screw large loop onto threads protruding from top of main frame to secure
decorave nut cover.
4) Take threaded pipe[E] from parts bag and screw in screw collar loop[B], a
minimum of 6 mm (1/4”). Lock into place with hexnut[F].
5) Run another hexnut down threaded pipe almost touching rst hexnut.
Now screw threaded pipe into mounng strap[I]. Mounng strap must be
posioned with extruded thread faced into outlet box[H]. Threaded pipe
must protrude out the back of mounng strap. Screw third hexnut onto end
of threaded pipe protruding from back of mounng strap.
6) Connect mounng strap to outlet box using the strap mounng screws[G].
7) Unscrew the threaded ring[C] from screw collar loop[B]. Take canopy[D]
and pass over screw collar loop. Approximately one half of the screw collar
loop exterior threads should be exposed. Adjust screw collar loop by turning
assembly up or down in mounng strap. Remove canopy.
8) Aer desired posion is found, ghten both top and boom hexnuts up
against the boom and top of the mounng strap.
9) Slip canopy over screw collar loop and thread on threaded ring.
10) Aach one end of chain[A] to boom of screw collar loop[B] by spreading end
link and then closing the link. Aach opposite end of chain to large loop[J] by
spreading opposite end link and then closing the link. To close the open chain
links, place a piece of cloth over the open link and use a pair of pliers to gently
squeeze the link closed.
11) Unscrew threaded ring[C], let canopy[D] and threaded ring slip down.
12) Weave electrical wire and ground wire through chain links[A] no more than
3 inches apart. Pass wire through screw collar loop[B], threaded ring[C],
canopy[D], threaded pipe[E], and into outlet box[H].
13) Grounding instrucons: (See Illus. a or b).
a) On xtures where mounng strap is provided with a hole and two raised
dimples, wrap ground wire from outlet box around green ground screw,
and thread into hole.
b) On xtures where a cupped washer is provided, aach ground wire from
outlet box under cupped washer and green ground screw, then thread
into mounng strap.
If xture is provided with ground wire, connect xture ground wire to outlet
box ground wire with wire connector aer following the above steps. Never
connect ground wire to black or white power supply wires.
14) Make wire connecon. Reference chart below for correct connecons and
wire accordingly.
Connect Black or Red
Supply Wire to:
Connect White Supply
Wire to:
Black White
*Parallel cord (round &
smooth)
*Parallel cord (square &
ridged)
Clear, Brown, Gold or
Black without Tracer
Clear, Brown, Gold or Black
with Tracer
Insulated wire (other
than green) with copper
conductor
Insulated wire (other
than green) with silver
conductor
*Note: When parallel wire (SPT
1 & SPT 2) are used. The neutral
wire is square shaped or ridged
and the other wire will be round
in shape or smooth (See illus.)
Neutral Wire
15) Raise canopy to ceiling.
16) Secure canopy in place by ghtening threaded ring[C] onto screw collar
loop[B].
17) Carefully lower glass shade[L] onto the xture. Slip the smaller opening over
the socket unl seated on the socket.
18) Secure glass to socket by screwing socket ring[M] onto threads on outside of
socket. Repeat for remaining eight (8) glass pieces.
19) Insert recommended bulbs (Not supplied).
GREEN GROUND
SCREW
CUPPED
WASHER
OUTLET BOX
GROUND
FIXTURE
GROUND
DIMPLES
WIRE CONNECTOR
OUTLET BOX
GROUND
GREEN GROUND
SCREW
FIXTURE
GROUND
a
b
Fixture Diagram
Parts List
Cauons
CAUTION – RISK OF SHOCK –
Disconnect Power at the main circuit breaker panel or main fusebox before
starng and during the installaon.
WARNING:
This xture is intended for installaon in accordance with the Naonal Electrical
Code (NEC) and all local code specicaons. If you are not familiar with code
requirements, installaon by a cered electrician is recommended.
CLEANING:
Always be certain that electric current is turned o before cleaning.
• Only a so damp cloth should be used. Harsh cleaning products may damage
the nish.
Installaon Instrucons
[A] Chain Links
[B] Screw Collar Loop
[C] Threaded Ring
[D] Canopy
[E] Threaded Pipe
[F] Hexnut
[G] Strap Mounting
Screws
[H] Outlet Box
[I] Mounting Strap
[J] Large Loop
[K] Main Frame
[L] Glass Shade
[M] Socket Ring
[N] Decorative Nut
Cover
L
M
A
B
D
H
I
F
G
E
C
J
N
K
1
2
3
Kichler Lighting 44036NI User manual
Kichler Lighting 52275NI User manual
Kichler Lighting 52231BK User manual
Kichler Lighting 52110OZ User manual
Kichler Lighting 52107OZ User manual
Kichler Lighting 52234BK User manual
Kichler Lighting 44034NI User manual
Kichler Lighting 44022NBR User manual
Kichler Lighting 43037DAG User manual
Kichler Lighting 52052CG User manual
Kichler 52109OZ Operating instructions
Home Decorators Collection 9401010820 Operating instructions
Generation Lighting OL5911EN/BK Installation guide
