Energy Suspension 19mm Rear Sway Bar Bushing Set Installation guide

Brand
Energy Suspension
Model
19mm Rear Sway Bar Bushing Set
Type
Installation guide
17073 1/NOV/00 BRH
Updated 17/JAN/02 BRH
Updated 11/JUL/03 BRH
Universal Instructions
for rod-eye / track bar bushings
Sleeve
Bushing
Rod-eye
REMEMBER: Some O.E. bushings use an outer metal shell,
this outer shell must be removed.
ONE PIECE STYLE BUSHINGONE PIECE STYLE BUSHING
(NOTE: If not supplied
in set, original sleeve/
shoulder bolt must
be re-used.)
Face of
bushing
Sleeve
Bushing
Rod-eye
REMEMBER: Some O.E. bushings use an outer metal shell,
this outer shell must be removed.
TWO PIECE STYLE BUSHINGTWO PIECE STYLE BUSHING
Bushing
Face of
bushing
(NOTE: If not supplied
in set, original sleeve/
shoulder bolt must
be re-used.)
1131 VIA CALLEJON, SAN CLEMENTE, CA 92673
R
It is recommended that if you are unfamiliar with this type of work that you refer to a qualified service center specializing in this type of work.
It is also recommended that if you choose to do this work yourself that a factory service manual be obtained for the proper procedures
pertaining to removal, replacement and proper torque specifications for your vehicle. This instruction set is intended as a guideline for the
safe installation of Energy Suspension’s polyurethane bushings, once you have removed the factory components from your vehicle.
Updated 8/JAN/03 BRH
2003 Energy Suspension. All rights reserved.2003 Energy Suspension. All rights reserved.
CC
May not be reproduced, in any form, or by any means,
without the written consent of Energy Suspension.
May not be reproduced, in any form, or by any means,
without the written consent of Energy Suspension.
Remove original rubber, clean I.D. of eye of any old rubber or rust. When installing polyurethane bushings, apply grease as instructed:
Apply light coat of grease to I.D. of the rod-eye. Apply light coat of grease to the I.D. and O.D. of bushings (all surfaces that contact metal).
Apply light coat of grease to the O.D. of sleeve. Apply light coat of grease to the faces of the bushings after they are installed.
17073 1/NOV/00 BRH
Updated 17/JAN/02 BRH
Updated 11/JUL/03 BRH
Universal Instructions
for rod-eye / track bar bushings
Sleeve
Bushing
Rod-eye
REMEMBER: Some O.E. bushings use an outer metal shell,
this outer shell must be removed.
ONE PIECE STYLE BUSHINGONE PIECE STYLE BUSHING
(NOTE: If not supplied
in set, original sleeve/
shoulder bolt must
be re-used.)
Face of
bushing
Sleeve
Bushing
Rod-eye
REMEMBER: Some O.E. bushings use an outer metal shell,
this outer shell must be removed.
TWO PIECE STYLE BUSHINGTWO PIECE STYLE BUSHING
Bushing
Face of
bushing
(NOTE: If not supplied
in set, original sleeve/
shoulder bolt must
be re-used.)
1131 VIA CALLEJON, SAN CLEMENTE, CA 92673
R
It is recommended that if you are unfamiliar with this type of work that you refer to a qualified service center specializing in this type of work.
It is also recommended that if you choose to do this work yourself that a factory service manual be obtained for the proper procedures
pertaining to removal, replacement and proper torque specifications for your vehicle. This instruction set is intended as a guideline for the
safe installation of Energy Suspension’s polyurethane bushings, once you have removed the factory components from your vehicle.
Updated 8/JAN/03 BRH
2003 Energy Suspension. All rights reserved.2003 Energy Suspension. All rights reserved.
CC
May not be reproduced, in any form, or by any means,
without the written consent of Energy Suspension.
May not be reproduced, in any form, or by any means,
without the written consent of Energy Suspension.
Remove original rubber, clean I.D. of eye of any old rubber or rust. When installing polyurethane bushings, apply grease as instructed:
Apply light coat of grease to I.D. of the rod-eye. Apply light coat of grease to the I.D. and O.D. of bushings (all surfaces that contact metal).
Apply light coat of grease to the O.D. of sleeve. Apply light coat of grease to the faces of the bushings after they are installed.
  • Page 1 1

Energy Suspension 19mm Rear Sway Bar Bushing Set Installation guide

Brand
Energy Suspension
Model
19mm Rear Sway Bar Bushing Set
Type
Installation guide
Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents