2. Energy Suspension
  3. Front or Rear Spring Bushings

Energy Suspension Front or Rear Spring Bushings Installation guide

  • Hello! I have analyzed the provided installation instructions for Energy Suspension Urethane bushings. The document guides you through removing old components and installing new bushings, focusing on proper cleaning and grease application. I'm ready to help with any questions you might have about the installation process.
  • What should be done with the original rubber and outer shell when installing bushings?
    What should be used to clean spring eyes and frame brackets?
    Where should grease be applied when installing Urethane bushings?
    What should be done if sleeve is not used?
Spring Main Eye and Shackle bushing Installation Instructions
Note: When a sleeve is
not used, apply a light
coat of grease to the
original shoulder bolt.
Remember: Most spring
eyes have an outer metal
shell. Some shackles are
this way as well. The outer
shell must be removed.
When installing Urethane bushings, apply grease as instructed: Remove the original
rubber and outer shell (when used) clean I.D. of the spring eyes and frame brackets of
any old rubber or rust with sand paper. Apply a light coat of grease to the eyes of both
spring and frame brackets. Apply a light coat to the I.D., O.D. and flange of the
bushings. (all surfaces that contact metal) Apply a light coat of grease to the O.D. of
the sleeves.)
17040
Updated 19/DEC/01 BRH
Outer
metal
shell
1131 VIA CALLEJON, SAN CLEMENTE, CA 92673
R
Updated 13/DEC/01 BRH
2002 Energy Suspension. All rights reserved.2002 Energy Suspension. All rights reserved.
CC
May not be reproduced, in any form, or by any means,
without the written consent of Energy Suspension.
May not be reproduced, in any form, or by any means,
without the written consent of Energy Suspension.
Spring Main Eye and Shackle bushing Installation Instructions
Note: When a sleeve is
not used, apply a light
coat of grease to the
original shoulder bolt.
Remember: Most spring
eyes have an outer metal
shell. Some shackles are
this way as well. The outer
shell must be removed.
When installing Urethane bushings, apply grease as instructed: Remove the original
rubber and outer shell (when used) clean I.D. of the spring eyes and frame brackets of
any old rubber or rust with sand paper. Apply a light coat of grease to the eyes of both
spring and frame brackets. Apply a light coat to the I.D., O.D. and flange of the
bushings. (all surfaces that contact metal) Apply a light coat of grease to the O.D. of
the sleeves.)
17040
Updated 19/DEC/01 BRH
Outer
metal
shell
1131 VIA CALLEJON, SAN CLEMENTE, CA 92673
R
Updated 13/DEC/01 BRH
2002 Energy Suspension. All rights reserved.2002 Energy Suspension. All rights reserved.
CC
May not be reproduced, in any form, or by any means,
without the written consent of Energy Suspension.
May not be reproduced, in any form, or by any means,
without the written consent of Energy Suspension.
Spring Main Eye and Shackle bushing Installation Instructions
Note: When a sleeve is
not used, apply a light
coat of grease to the
original shoulder bolt.
Remember: Most spring
eyes have an outer metal
shell. Some shackles are
this way as well. The outer
shell must be removed.
When installing Urethane bushings, apply grease as instructed: Remove the original
rubber and outer shell (when used) clean I.D. of the spring eyes and frame brackets of
any old rubber or rust with sand paper. Apply a light coat of grease to the eyes of both
spring and frame brackets. Apply a light coat to the I.D., O.D. and flange of the
bushings. (all surfaces that contact metal) Apply a light coat of grease to the O.D. of
the sleeves.)
17040
Updated 19/DEC/01 BRH
Outer
metal
shell
1131 VIA CALLEJON, SAN CLEMENTE, CA 92673
R
Updated 13/DEC/01 BRH
2002 Energy Suspension. All rights reserved.2002 Energy Suspension. All rights reserved.
CC
May not be reproduced, in any form, or by any means,
without the written consent of Energy Suspension.
May not be reproduced, in any form, or by any means,
without the written consent of Energy Suspension.
Spring Main Eye and Shackle bushing Installation Instructions
Note: When a sleeve is
not used, apply a light
coat of grease to the
original shoulder bolt.
Remember: Most spring
eyes have an outer metal
shell. Some shackles are
this way as well. The outer
shell must be removed.
When installing Urethane bushings, apply grease as instructed: Remove the original
rubber and outer shell (when used) clean I.D. of the spring eyes and frame brackets of
any old rubber or rust with sand paper. Apply a light coat of grease to the eyes of both
spring and frame brackets. Apply a light coat to the I.D., O.D. and flange of the
bushings. (all surfaces that contact metal) Apply a light coat of grease to the O.D. of
the sleeves.)
17040
Updated 19/DEC/01 BRH
Outer
metal
shell
1131 VIA CALLEJON, SAN CLEMENTE, CA 92673
R
Updated 13/DEC/01 BRH
2002 Energy Suspension. All rights reserved.2002 Energy Suspension. All rights reserved.
CC
May not be reproduced, in any form, or by any means,
without the written consent of Energy Suspension.
May not be reproduced, in any form, or by any means,
without the written consent of Energy Suspension.
/