Arduino Nano 33 BLE Sense Rev2 Full Pinout

Arduino
Brand
Arduino
Model
Nano 33 BLE Sense Rev2
Type
Full Pinout
This work is licensed under
the Creative Commons
Attribution-ShareAlike 4.0
International License. To view a
copy of this license, visit http://
creativecommons.org/licenses/
by-sa/4.0/ or send a letter to
Creative Commons, PO Box 1866,
Mountain View, CA 94042, USA.
SKU code: ABX00069
Full Pinout - Page 1 of 4
Last update: 22 Dec, 2022
VIN 5-21V input to the board
CIPO/COPI have previously been
referred to as MISO/MOSI
MAXIMUM input current per pin
is 5mA
MAXIMUM output current per pin
is 15mA
MAXIMUM current overall is 25mA
for the sum of all GPIOs and VDDs
Legend:
Power Power Input
Power Output
Ground
GPIO Digital External
Analog External
Main Part
Secondary Part
Internal Component
Other Pins (Reset, System
Control, Debugging)
I2C Default
SPI Default
UART/USART Default
Other SERIAL Communication
Analog Default
PWM/Timer
LED
RGB LED
Short Circuit
allowed functions
TOP VIEW
GND
D1/RX
D0/TX
P1.08
P1.01
Micro
Micro
Micro SPISPI
I2C
CIPO
COPI
P1.02
P0.27
P1.14
P1.13
P1.15
P1.12
P1.11
P1.10
P1.03
P0.13
+3V3
AREF
A0P0.04
A1P0.05
A2P0.30
A3P0.29
A4P0.31
A5P0.02
A6P0.28
A7P0.03
+5V
GND
VIN
SCK
SDA
SCL
RESETRESET
~D12
~D11
~D10
~D9
~D8
~D7
~D6
~D5
~D4
~D3
~D2
D13~
P0.21
P0.23
P1.09
P0.13
Power
BUILT_IN LED
DEFINE
LED_PWR
LED_BUILTIN
nRF52840
WARNING!
Advanced Section
The following information is for advanced use only and
may not be officially supported by Arduino software
This work is licensed under
the Creative Commons
Attribution-ShareAlike 4.0
International License. To view a
copy of this license, visit http://
creativecommons.org/licenses/
by-sa/4.0/ or send a letter to
Creative Commons, PO Box 1866,
Mountain View, CA 94042, USA.
SKU code: ABX00069
Full Pinout - Page 3 of 4
Last update: 22 Dec, 2022
VIN 5-21V input to the board
CIPO/COPI have previously been
referred to as MISO/MOSI
MAXIMUM input current per pin
is 5mA
MAXIMUM output current per pin
is 15mA
MAXIMUM current overall is 25mA
for the sum of all GPIOs and VDDs
Legend:
Power Power Input
Power Output
Ground
GPIO Digital External
Analog External
Main Part
Secondary Part
Internal Component
Other Pins (Reset, System
Control, Debugging)
I2C Default
SPI Default
UART/USART Default
Other SERIAL Communication
Analog Default
PWM/Timer
LED
RGB LED
Short Circuit
allowed functions
TOP VIEW
SDA1
INTP0.19
LDA+3V3
SCLP0.15
The sensors BMI270, BMM150, LPS22HBTR
and HS3003 are powered by p0.22, that
can be set to zero to turn them off
MP34DT06JTR is powered by p0.17,
that can be set to zero to turn it off
SCL1
VDD+3V3
APDS-9960
Digital proximity, Ambient light,
RGBa and Gesture sensor
VDDP0.17
CLKP0.26
DOUTP0.25
LRP0.17
MP34DT06JTR
Microphone
USB N
+5V
USB P
USB ID
GND
USB_DM
USB_DP
P0.24red
P0.16greenRGB LED
P0.06blue
nRF52840
Y
X
Z
DEFINE
TEST
LEDR
LEDG
LEDB
SWDIO
SWCLK
SDAP0.14
VDD P0.22
SDA1
SCL1
SDA P0.14
SCL P0.15
HS3003
Humidity and Temperature sensor
Q1 nMOS switches on and
off the BUILT_IN LED and
it is driven by p0.13 (SCK)
Q1 nMOS
GATEP0.13
DRAINBUILT_IN LED
VDDP0.22
VDDIOP0.22
SDxP0.14SDA1
SCxP0.15SCL1
CSBP0.22
SDOGND
INT1P0.11
INT2P0.20
BMI270
Inertial Motion Unit 6 axis
VCCP0.22
VCCIOP0.22
SDAP0.14SDA1
SCLP0.15SCL1
CSP0.22
SDOGND
LPS22HBTR
Pressure sensor
INT1P0.12
VDD P0.22
VDDIO P0.22
SDI P0.14 SDA1
SCK P0.15 SCL1
PS P0.22
CS GND
SDO GND
BMM150
Magnetometer 3 axis IMU
This work is licensed under
the Creative Commons
Attribution-ShareAlike 4.0
International License. To view a
copy of this license, visit http://
creativecommons.org/licenses/
by-sa/4.0/ or send a letter to
Creative Commons, PO Box 1866,
Mountain View, CA 94042, USA.
SKU code: ABX00069
Full Pinout - Page 4 of 4
Last update: 22 Dec, 2022
VIN 5-21V input to the board
CIPO/COPI have previously been
referred to as MISO/MOSI
MAXIMUM input current per pin
is 5mA
MAXIMUM output current per pin
is 15mA
MAXIMUM current overall is 25mA
for the sum of all GPIOs and VDDs
Legend:
Power Power Input
Power Output
Ground
GPIO Digital External
Analog External
Main Part
Secondary Part
Internal Component
Other Pins (Reset, System
Control, Debugging)
I2C Default
SPI Default
UART/USART Default
Other SERIAL Communication
Analog Default
PWM/Timer
LED
RGB LED
Short Circuit
allowed functions
BOTTOM
VIEW
TOP VIEW
Making a short circuit with this solder jumper,
the indentical one on the bottom or both
(they are in parallel), connects the VBUS to the pin
+5V
SWDIO
SWCLK
VUSB
GND
USB_N
USB_P
VBUS
~D7
~D8 P0.10
P0.09
NFC2
NFC1
3.3V
Making a short circuit using the solder jumper allows only
the function in the Short Circuit Pin cells and also it changes
the Pad connection of the pins D7 and D8 in P0.09 and P0.10.
TEST
+3V3
GND
Cutting the solder jumper allows to power via
battery or from an external 3.3V power source
connecting the battery’s ground to the GND
pin and the battery’s positive to the 3.3V pin.
135
26
1
2
3
5
6
+3V3
SWDIO
SWCLK
GND
P0.08
15-SWDIO
11-SWCLK
RESET
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4

Arduino Nano 33 BLE Sense Rev2 Full Pinout

Arduino
Brand
Arduino
Model
Nano 33 BLE Sense Rev2
Type
Full Pinout
Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents