i3 International 5i00XX Quick Connection Guide
- Category
- Digital Video Recorders (DVR)
- Type
- Quick Connection Guide
i3 Technical Support: 1.877.877.7241 Rev. 150501
Quick Connection Guide 5i00XX-series
Thank you for purchasing the i3 Digital Video Management System
(DVMS). The following items should be included in the i3 DVMS box.
If any of these items are missing, please contact your dealer or call
our Customer Care Department toll free at 1.866.840.0004.
Standard accessories:
• HDD SATA keys (2 pcs)
• DVMS door keys (2 pcs), attached to the back of the unit
• USB keyboard
• USB mouse
• Power cord (2 pcs)
• SRX-Pro Software & Utilities DVD
• Motherboard CD(s)
• Security labels (2 pcs)
• Rackmount bracket (Ear x 2 pcs, Aluminum handle x 2 pcs) +
bracket screws (6 pcs)
• Optional. Wallmount bracket (2 pcs) + bracket screws (8 pcs)
Installation Requirements:
When selecting a storage location for your system, be sure to avoid:
• excessive heat, such as direct sunlight or heating appliances
• moisture, dust, and smoke
• magnetic fields or electrical waves
• temperatures below 5º Celsius or 41º Fahrenheit
• any obstructions to the system’s ventilation holes
Before installing this system, always ensure the:
• power source is located within 3 feet or 1 meter of the UPS
• power is switched off (**Do not plug in the DVMS unit)
• system and its connecting cables have sufficient space system is
placed on an even surface system is situated far from electronic
equipment such as microwaves, radios, fridge compressors,
or any type of wireless equipment such as telephones or cell
phones)
• system is at room temperature (18º – 25º C or 64º – 77º F)
POWER
REC
WD
WD SWITCH
HDD1 SATA
HDD2 SATA
HDD3 SATA
DVD Drive
USB 2.0
Power
Button
Internet Port
DisplayPort connector
(Not in Use)
Firewire
(Not in Use)
USB 3.0
USB 2.0
Mic Input (Not in Use)
Speaker Output (Not in Use)
Audio Input (Not in Use)
DVI-I to VGA Monitor Port
DVI
(Not in Use)
eSATA
(Not in Use)
Sensor Inputs (2)
Control Outputs (2)
RS-485 (PTZ)
Internet Port
DisplayPort connector
(Not in Use)
Firewire
(Not in Use)
USB 3.0
USB 2.0
Mic Input (Not in Use)
Speaker Output (Not in Use)
Audio Input (Not in Use)
DVI-I to VGA
Monitor Port
DVI
(Not in Use)
eSATA
(Not in Use)
Internet Port
DisplayPort connector
(Not in Use)
Firewire
(Not in Use)
USB 3.0
USB 2.0
Mic Input (Not in Use)
Speaker Output (Not in Use)
Audio Input (Not in Use)
DVI-I to VGA Monitor Port
DVI
(Not in Use)
eSATA
(Not in Use)
Internet Port
DisplayPort connector
(Not in Use)
Firewire
(Not in Use)
USB 3.0
USB 2.0
Mic Input (Not in Use)
Speaker Output (Not in Use)
Audio Input (Not in Use)
DVI-I to VGA
Monitor Port
DVI
(Not in Use)
eSATA
(Not in Use)
1-16 Video In (Analog)
1-16 Video Out (Analog)
1-16 Video In (IP)+ PoE
Main Power Supply.
Auto Switchable (110/240 AC)
PoE Power Supply.
Auto Switchable (110/240 AC)
Power Toggle Switch
PoE Power Supply.
Auto Switchable (110/240 AC)
Power Toggle Switch
Sensor Inputs (2)
Control Outputs (2)
RS-485 (PTZ)
Main Power Supply.
Auto Switchable (110/240 AC)
Power Supply.
Auto Switchable (110/240 AC)
Power Supply.
Auto Switchable (110/240 AC)
1-16 Video In (Analog)
1-16 Video Out (Analog)
1-16 External
RCA Outputs
1-8 Audio
Inputs
1-16 External
VGA Outputs
1-16 External
RCA Outputs
1-8 Audio
Inputs
1-16 External
VGA Outputs
1-16. 75 Ω Impedance
1-16. 75 Ω Impedance
POWER
REC
WD
WD SWITCH
DVD Drive
USB 2.0
Power
Button
POWER
REC
WD
WD SWITCH
HDD1 SATA
HDD2 SATA
HDD3 SATA
DVD Drive
USB 2.0
Power
Button
Internet Port
DisplayPort connector
(Not in Use)
Firewire
(Not in Use)
USB 3.0
USB 2.0
Mic Input (Not in Use)
Speaker Output (Not in Use)
Audio Input (Not in Use)
DVI-I to VGA Monitor Port
DVI
(Not in Use)
eSATA
(Not in Use)
Sensor Inputs (2)
Control Outputs (2)
RS-485 (PTZ)
Internet Port
DisplayPort connector
(Not in Use)
Firewire
(Not in Use)
USB 3.0
USB 2.0
Mic Input (Not in Use)
Speaker Output (Not in Use)
Audio Input (Not in Use)
DVI-I to VGA
Monitor Port
DVI
(Not in Use)
eSATA
(Not in Use)
Internet Port
DisplayPort connector
(Not in Use)
Firewire
(Not in Use)
USB 3.0
USB 2.0
Mic Input (Not in Use)
Speaker Output (Not in Use)
Audio Input (Not in Use)
DVI-I to VGA Monitor Port
DVI
(Not in Use)
eSATA
(Not in Use)
Internet Port
DisplayPort connector
(Not in Use)
Firewire
(Not in Use)
USB 3.0
USB 2.0
Mic Input (Not in Use)
Speaker Output (Not in Use)
Audio Input (Not in Use)
DVI-I to VGA
Monitor Port
DVI
(Not in Use)
eSATA
(Not in Use)
1-16 Video In (Analog)
1-16 Video Out (Analog)
1-16 Video In (IP)+ PoE
Main Power Supply.
Auto Switchable (110/240 AC)
PoE Power Supply.
Auto Switchable (110/240 AC)
Power Toggle Switch
PoE Power Supply.
Auto Switchable (110/240 AC)
Power Toggle Switch
Sensor Inputs (2)
Control Outputs (2)
RS-485 (PTZ)
Main Power Supply.
Auto Switchable (110/240 AC)
Power Supply.
Auto Switchable (110/240 AC)
Power Supply.
Auto Switchable (110/240 AC)
1-16 Video In (Analog)
1-16 Video Out (Analog)
1-16 External
RCA Outputs
1-8 Audio
Inputs
1-16 External
VGA Outputs
1-16 External
RCA Outputs
1-8 Audio
Inputs
1-16 External
VGA Outputs
1-16. 75 Ω Impedance
1-16. 75 Ω Impedance
POWER
REC
WD
WD SWITCH
DVD Drive
USB 2.0
Power
Button
Uninterrupted power supply (UPS) (min. 1000VA) must always be used with the i3 DVMS;
otherwise, all warranties will be voided.
i3 Technical Support: 1.877.877.7241 Rev. 150501
Setting Up the SRX-Pro DVMS
Before installation: 1. ground yourself. This will remove any static electrical charge your body might be carrying. 2. Connect all cables and peripheral devices by following instructions below.
Plug in the monitor. For VGA monitors, use the DVI-VGA
adapter included with your accessories. For DVI monitors,
plug in directly into the DVI port on the motherboard.
Plug the mouse and keyboard into the USB ports in
the back of the unit.
Connect BOTH power cables to an Uninterruptible
Power Supply (UPS). UPS must be used to maintain
unit warranty.
Time Zone Adjustment
All DVMS units sold by i3 International are pre-set to Eastern Time zone (GMT -5:00). It is imperative that you configure the time zone setting on the first system startup according to the physical location of the unit. If the
DVMS is later re-located to a different time zone, this setting must be changed once again. All previously-recorded data must be formatted after each time zone change. Failure to do so may result in system malfunction.
Once the SRX-Pro Server starts for the first time, the message in Fig. 1 will be displayed. Click Yes if the DVMS is being installed in the Eastern time zone (GMT -5:00). Click No if the DVMS is being installed in a different time
zone - this will halt the SRX-Pro software startup and allow you a chance to set your DVR/NVR’s timezone.
If the DVMS is being installed in a different time zone, follow instructions below:
1. On Windows Desktop, click on the System Time in the bottom right-hand corner.
2. In the calendar window, click Change date and time settings...
3. In Date and Time tab, click on Change time zone... button and select the correct time zone in the drop down list.
4. Click OK. Click OK again to close Date and Time window.
5. Launch SRX-Pro Server softare by clicking on Start > All Programs > SRX-Pro Server
6. Once the software loads, a message in Fig. 2 will be displayed on the screen.
7. Click OK (highly recommended) to format all storage drives and erase video data recorded in a different time zone.
8. Click OK in the “All old data will be formatted” warning window, Allocation window will be displayed in the top left corner.
9. Wait until the “Start allocating selected drive(s). It may take several minutes to finish.” message changes to “Storage Drives have been allocated”.
10. Click OK in the Allocation window to close it. The login window will be displayed on the screen. The default Administrator Login/Password is i3admin / i3admin
Note: Default administrative Login/
Password for SRX-Pro v.3.1
and above is: i3admin / i3admin
Fig. 1. Time Zone Warning Message on first startup
Fig. 2. Time Zone data format message
Connect the power cable to the PoE power supply
on your DVMS. Then, put the toggle power switch
underneath in the ON position.
Finally, connect the power cable to the the Main
power supply on your DVMS. The system will
power on automatically.
STEP 1
STEP 2
STEP 3
STEP 4
STEP 5
STEP 6
Connect all IP camera cables to the PoE switch ports
on the back of the chassis.
STEP 7
If the unit does not power on automatically, press and hold
the toggle button power switch at the front of your unit for
2 sec. The system will then power on.
-
1
-
2
i3 International 5i00XX Quick Connection Guide
- Category
- Digital Video Recorders (DVR)
- Type
- Quick Connection Guide
Ask a question and I''ll find the answer in the document
Finding information in a document is now easier with AI
Related papers
-
i3 International 4i00XX Quick Connection Guide
-
-
-
-
-
-
-
-
-
Other documents
-
American Dynamics Intellex 4.12 Installation And Configuration Manual
-
American Dynamics Intellex Ultra Installation And Configuration Manual
-
American Dynamics Intellex Intellex DVMS Installation And Configuration Manual
-
Safety Vision ICOP PRO HD User guide
-
-
Safety Vision ICOP PRO Monitor User guide
-
VocoPro DVM-100G Owner's manual
-
American Dynamics AD2089-1 User manual
-
ERNITEC EDNS4000/HYBRID User manual
