Barco X2.8R Installation guide

Brand: Barco

Model: X2.8R

Type: Installation guide

X2.8R

Installation manual

Indoor installation

R5906160/00

28/02/2018

Barco Visual (Beijing) Electronics Co., Ltd

地址：北京市昌平区中关村科技园昌平园昌盛路 16号

Phone: +86 10 8010 1166

Fax: +86 10 8970 2793

Support: www.barco.com/en/support

Visit us at the web: www.barco.com

Registered address: Barco NV

President Kennedypark 35, 8500 Kortrijk, Belgium

Phone: +32 56.23.32.11

Fax: +32 56.26.22.62

Support: www.barco.com/en/support

Visit us at the web: www.barco.com

Printed in Belgium

Changes

Barco p rovides this manual ’as is’ without warranty of any kind, either e xpressed o r implied, including but not limited to the implied war-

ranties or m erchantability and ﬁtness for a particular purpose. Barco may m ake improvements and/or cha nges to the product(s) and/or the

program(s) described in this publication at any time w ithout notice.

This pub lication c ould contain technical inaccuracies or typographical errors. Changes are periodically made to the information in this

publication; these changes are incorporated in new editions of this publication.

The latest edition of Barco manua ls can be downloaded from the Barco web site w

ww.bar co.com or from the secured B arco web site

ttps://www.barco.com/en/signin.

EMC statements

EN55032/CISPR32 Class A MME (M u ltiMedia Equipm ent)

Warning : This equipm ent is c ompliant with Class A o f CISPR 32. In a residential environm ent this equipment may cause radio interfer-

ence.

Class A ITE (Information Technology Equipment)

Warning : This is a class A product. In a dom estic environment this product may cause radio interference in which case the user may be

required to take adequate meas ures.

Safety regulation (Intertek Statement)

This pr oduct is conforming to UL Std 60950–1 and CS A Std C22.2 NO . 6095 0–1.

stored in a retrieval s ystem without the prior written consent of Barco.

Federal Communications Commission (FCC Statement)

This equipment has been tested and found to c omply with the limits for a class A digital device, pursuant to Part 15 of the FCC rules.

These limits a re designed to provide reasonable protection against harmful interference when the equipment is operated in a comm ercial

environment. This eq uipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with

the instruction manual, may cause harmful interference to radio communications. Oper ation of this equipment in a residential area may

cause harmful interference, in which c ase t he user will be responsible for correcting any interference at his own ex pense

Changes or modiﬁc ations not expressly approved by the par ty respons

ible for compliance could v oid the user’s authority to operate the

equipment

Guaran tee and Compensat ion

Barco provides a guarantee relating to perfect man ufacturing as part of the legally stipulated terms of guarantee. On receipt, the purchaser

must immediately inspect a ll delivered goods for dam age incurred during transport, as well as for material and manufacturing faults Barc o

must be informed im mediately in writing of any c omplaints.

The period of guarantee begins on the date of transfer of risks, in the c ase of special systems and software on the date of commissioning,

at latest 30 days after the transfer of risks. In the event of justiﬁed notice of com plaint, Barco can repair the fault or p rovide a replacement

at its own discretion within an appr opriate period. If this measure proves to be impossible or uns uccessful, the purchaser can demand a

reduction in the purchase price or cancellation of the contract. All other claims, in par ticular those relating to compensation for direct or

indirect damage, and also damage attributed to the operation of s oftware as well as to other services provided by Barco, being a component

of the system or independent service, will be deemed invalid provided the dam age is n ot pro ven to be attributed to the absence of properties

guaranteed in writing or due to the intent or gross negligence or part of Barco.

If the pur chaser or a third party carries out modiﬁcations or repairs o n go ods delivered by Barco, or if the goods are ha ndled inco rrectly,

in particular if the systems a re operated incorrectly or if, after the trans fer o f risks, the goods are subjec t to inﬂuences not agreed upon in

the contract, all guarantee claims o f the pur chaser will be rendered invalid. Not included in the guarantee coverage are system failures

which are attributed to programs or special electronic circuitry provided by the purchaser, e.g. interfaces. Normal wear as well as norm al

maintenance are not subjec t to the guarantee p rovided by Barco either.

The environmental conditions as

well as the servicing and m aintenance regulations speciﬁed in this m anual must be complied w ith by the

customer.

Trademarks

Brand and product names mentioned in this manual may be trademarks, registered tradem arks or copyrights of their respective holders.

All br and and produc t names me ntioned in this manual serve as commen ts or examples and are not to be understood as adv ertising for

the products or their manufacturers.

Table of contents
TABLE OF CON TENTS
Safety................................................................................................................ 3
1 Safety guidelines .................................................................................................................... 3
2 Important safety instructions ........................................................................................................ 4
3 Important warnings . ................................................................................................................. 4
4 Proper usage ........................................................................................................................ 6
Installation requirements ........................................................................................ 9
1 Mechanical requirements for the X2.8R display .................................................................................... 9
2 Electrical requirements for the X2.8R display . . .................................................................................... 9
3 System requirements for the Control software . . ................................................................................... 10
System overview ..................................................................................................11
1 Introduction ..........................................................................................................................11
Components of the X2.8R display..............................................................................13
1 X2.8R tiles ...........................................................................................................................13
2 X2.8R rental truss/ﬂoor setup accessories .........................................................................................15
3 X2.8R rental base stand setup accessories ........................................................................................16
4 X2.8R ﬂightcase .....................................................................................................................17
5 Inﬁnipix™ Platform ..................................................................................................................17
6 Inﬁnipix™ Suite User Interface......................................................................................................19
7 Updates .............................................................................................................................. 19
Setup process of the X2.8R display............................................................................21
1 Locking and unlocking the X2.8R rental tile ........................................................................................21
2 Setting a curve on an X2.8R display................................................................................................24
3 Setting up a ﬂoor mount X2.8R display . . .. . ........................................................................................25
4 Set up a hanging X2.8R dis play . ...................................................................................................28
Cabling of the X2.8R display ....................................................................................31
1 X2.8R tile connectivity ............................................................................................................... 31
2 Power cabling of the X2.8R display................................................................................................. 32
3 Data cabling of the X2.8R display................................................................................................... 33
Speciﬁcations......................................................................................................35
1 Speciﬁcations........................................................................................................................35
2 X2.8R tile dimension ................................................................................................................36
3 Dimensions of the X 2.8R truss/ﬂoor beams ........................................................................................36
4 Dimensions of the X2.8R stacker system...........................................................................................37
5 Weight of individual parts of the X2.8R disp lay.....................................................................................38
6 Ballast values for a base stand X2.8R display .....................................................................................38
7 Ground pressure of a base stand X 2.8R d isplay ................................................................................... 39
Service ..............................................................................................................41
1 Service via front access.............................................................................................................41
1.1 Remove module ...............................................................................................................41
1.2 Remove connection box ...................................................................................................... 43
1.3 Install connection box.........................................................................................................44
1.4 Install module .................................................................................................................45
2 Service via rear access.............................................................................................................. 46
2.1 Remove connection box ...................................................................................................... 46
2.2 Remove module ...............................................................................................................47
2.3 Install module .................................................................................................................48
2.4 Install connection box.........................................................................................................49
Maintenance........................................................................................................51
1 Cleaning the front of X2.8R tiles . . .................................................................................................. 51
Product green compliance.. .. ............ .. .............. .. .. .......... .. .. .............. .. .............. .. .. ...53
1 Disposal information................................................................................................................. 53
2 RoHS compliance ................................................................................................................... 53
3 Production address .................................................................................................................. 54
R5906160 X2.8R 28/02/2018
1

Table of contents

2 R5906160 X2.8R 28/02/2018

1. Safety

1. SAFETY

About this chapter

Read this chapter attentively. It contains im portant information to prevent personal injury while installing the X2.8R display. Fu rther-

more, it includes several cautions to prevent damage to the X2.8R tiles. E nsure that you understand and follow all safety guidelines,

safety instructions and warnings mentioned in this chapter before installing the X2.8R tiles. After this chapter, additional “warnings”

and “cautions” are given de pending on the installation procedure. R ead and follow these “warnings” and “cautions” as well.

Clariﬁcation of the term “X2.8R” used in this document

When referring in this document to the term “X2.8R” means that the co ntent is applicable for following B arco products:

• X2.8R

1.1 Safety g uidelines

Personal protection

WARNING: Ensure yo u un derstand and follow a ll the safety guidelines, safety instructions, warnings and

cautions mentioned in this manual.

WARNING: Be aware of suspended loads.

WARNING: Wear a hard h at to reduce the risk of perso nal injury.

WARNING: Be careful while working with heavy loads.

WARNING: Mind your ﬁngers w hile working w ith heavy loads.

Installation personnel

This installation must be performed by authorized and qualiﬁed technical personnel only.

Accredited safety ofﬁcers must ens ure the safety o f the site, construction, assembly, c onnection, use, disman tling, transport etc. of

such saf ety crit ica l sys tems.

Operator

The products spec iﬁed in the manual only can be oper ated and used by the professional who meets the requirements for this work.

The operator shall obey the instructi

on in this document, especially the safety and w arning note herein. Due to the relevant training

and experience, professional have a more in-depth understanding of this product, they can avoid the risk of the process of the

operation.

The non-professional shall not asse mbly and disassembly at their own discretion, in case o f high-v oltage electric sho ck.

Caution

Installation should be performed on ly after you are thoroughly familiar with all of the proper safety checks and installation instructions.

To do otherwise increases the risk of hazards and injury to the us er.

Assembly parts are designed for intended use only in c onjunction with X2.8R displays.

Do not modify and/or replicate any component. B arco uses speciﬁc m aterials and m anufacturing processes in order to achieve part

strength. Consult Barco for as

sistance with custom applications.

R5906160 X2.8R 28/02/2018

1. Safety

Always follow Barco installation instructions. Contact Barco if you should have any question regarding the safety of an application.

The manufacturer assum es no liability for incorrect, inadequate, irresponsible or unsafe assem bly o f system s. The system must

comply with the local safety regulations regarding environmental conditions, solidity ﬁnal construction, etc…

Notice on safety

This equ ipment is built in acco rdance with the requirements o f the international safety standards IEC60950 -1, E N60950-1,

UL60950-1 and CAN/CSA C22.2 No.60950-1, which are the safety standards of information technology equipment including

electrical business equipment. Thes e s afety standards impose im portant requirements on the use of safety critical co mponents,

materials and insulation, in order to protect the user or operator against risk of electric shock and energy hazard and ha ving access

to live parts. Safety standards also impose limits to the internal and external temperature rises, radiation levels, mec hanical stability

and strength, e nclosure construction and protection against the risk of ﬁre. Sim ulated single fault condition testing ensures the

safety of the equipment to the user even whe n the equipment’s normal operation fails.

Product care

Structural & mounting components s hould be kept dry, c lean, lubricated (only if recommended), coated properly, and otherwise

maintained in a manner consistent with part design. Barco produc ts m ust be used in a m anner c

onsistent with their design and

inspected on a ro utine basis for security, wear, deformation, corrosion and any other circumstances that may affect the load handling

capability of the part.

Barco recommends ins pections at regular intervals for all installations and increasing in frequency for more critical installations. If

a part is found to hav e dam age, w hich may cause a decreas e in load capability, the part must be removed for service or replaced

immediately.

Under n o circumstances are Barco parts repairable b y anyone other than Barco.

1.2 Important safety instructions

Instructions:

• Read these instructions.

• Keep these instructions.

• Heed all warnings.

• Follow all instructions.

• Clean only with materials or chem icals that are iner t, nonab rasive, n oncorrosive and non-marking. C onsult the manufacturer

for further advice should any doubts exist r egarding any cleaning procedure.

• Do not block ventilation openings. Install in accordance with the manufacturers instructions.

• Do not install near a ny heat so urces such as radiators, heat registers, stoves, or other apparatus (including a mpliﬁers) that

produce he at.

• Do not defeat the safety purpose of the polarized or grounding type plugs/sockets. If the provided sockets/plugs are damaged

then replacement of the defective parts must be undertaken immediately.

• Protect the power/data cords from being walked on or pinched particularly at plugs, convenience recep tacles, an d the point

where they exit from the appar atus. Replace damaged power/data cords immediately.

• Only use attachments/accessories speciﬁed by the manufacturer.

• Disconnect the power to this apparatus during lightning storms or provide suitable additional lightning p rotection. Unplug this

apparatus when unused for long period of time.

• Refer all servicing to qualiﬁed service technicians/personnel. Se rvicing is required when the apparatus has been damaged in

any way, such as power-supply cord or plug is damage d, the appa ratus d oes not opera te norm ally, or has been dropped.

• Use only with systems or p eripherals speciﬁed by the m anufacturer, or sold with the apparatus. Use c aution during lifting/moving

or transporting to avoid damage by possible tipping.

• Do not use dam aged LED tiles. Replace da maged parts immediately. En sure th at the spring of each locking m e chanism (latch)

is functioning properly. If not, replac e immediately.

1.3 Important warnings

Important warnings:

Risk of electric shock:

Do not open. To reduce the risk of electric shock, do not rem ove cov er (or back ). No use r-serviceable parts inside. Refer servicing

to qualiﬁed service personnel.

Maximum and m inimu m ambient tem perature

The max imum ambient temper ature for the LED wall is 40°C (104°F), the minimum temperature is -10°C (14°F).

Low Voltage Surg e Protection Device required

R5906160 X2.8R 28/02/2018

1. Safety

Due to the dam aging effects of lightning, utility switching and switching electric m otors of other us ers on the mains, this product

needs to be protected by means of a Surge Protection Device. If this product is connected to the mains through the powe r box

from Barco this protection device is already inc orporated and no extra measures need to be taken. If this product is connected to

the mains through a power distribution box from another party, please ve rify that a Low Voltage Surge Protection Device according

EN61643-11 or UL 1449 is in place.

High leakag e current:

The com bination of multiple tiles in an installation r esults in increased levels of leakage c urrent. In order to avoid risk of electric

shock due to high leakage c urrent, proper grounding of the installation is required.

Flammable materials:

Keep ﬂammable m aterials away from the installation (such as curtains). A lot of energy is transferred into heat. The installation

should be such that the amount of air ﬂow required for safe operation of t he equipment is no t compromised. Proper ve ntilation m ust

be provided.

Risk of electric shock / Risk of ﬁre:

The X2.8R tile requires 100-240VAC, 50-60Hz, 0,6A a t 230VA C to function.

To protect against risk of ﬁre caused by overloading of pow er cables:

• When working on 200-240VAC, a M AX IMU M of 14 tiles may be connec ted in 1 chain. Each power source cable supplying

MAXIMUM 14 tiles shou ld be protected by a circuit breaker or fuses rated:

- 16 A / 250 VA C (EU/APAC)

- 15 A / 250 VAC (USA/Canada)

• When working on 100-120VAC, a M AX IMU M of 10 tiles may be connec ted in 1 chain. Each power source cable supplying

MAXIMUM 10 tiles shou ld be protected by a circuit breaker or fuses rated:

- 15 A / 250 VAC (USA/Canada)

The power limits of the used power connectors needs to be followed. A C 13/C14 connector is lim ited to 10A. An Amphenol con nector

is limited to 16A.

ESD and LED’s:

LED components used in X2.8R tiles are ESD (Electro-Static Discharge) sens itive. To prevent the possibility of destroying LE D

components do not touch either in operation or while s witched off. Always use ESD-gloves.

Disconnect device:

When the appliance inlets of the individual tiles are not accessible, the socket outlets supplying the rack shall be installed near t he

equipment and b e eas ily accessible, or a r eadily acces sible gen eral disconnect device shall be incorporated in the ﬁxed wiring.

This equipm ent M US T be earthed:

In order to protect ag ainst risk of electric shock, the installation should be p roperly grounded. Defeating the purpose of the grounding

type plug will expose yo u to the risk of electric shoc k.

Power system:

It is recommended to use a T N-S power distribution system (a pow er distribution system with a separate neutral and grounding

conductor) in order to avoid large groun d current loops due to voltage differences in the neutral c onductor. The total electrical

installation should be protected by an appropriately rated disconnect switch, circuit br eakers, over voltage protector and Ground Fault

Current Interrupters. The installation shall be done according to the local electrical installation co des. In Europe special attention

should be given to HD 60364, Harmonization Docum ent for electrical installation of buildings. In Germ any VDE 0100 should be

adhered to. In America, special attention should be given to the N ational Elec trical Code, ANSI/N FPA 70.

Mains cords:

The pow er cords delivered with this system have special properties for safety. T hey are no t user serviceable. If the power cords a re

damaged, replace them only with new ones. Nev er try to repair a power cord.

LED s :

The LEDs used on the X 2.8R tiles are fragile. Never push with a hard or sharp object onto the lens of the LED as this may cause

damage to the LE D. The maximum allowed load upon the lens of the LED is 300 gram/LED. Be careful when installing a shader

upon th e X2.8R tiles. Shaders only ﬁt in one direction a n d this should be veriﬁed before pushing into ﬁnal position. Use your bare

ﬁngers (not nails) to press the shader over the LEDs . Use your ﬁnger nails to press upon the framework of the shader between the

LEDs (not upon the LEDs) to push the shader in its ﬁnal position.

Do not hot plug:

Do not hot plug any ca bles. Dam age to the conn ector pins may occur. Resulting dam age is not covered u nder warranty.

Maximum allowed d isplay height:

The maximum height of a X2.8R display is limited: maximum 12 tiles high standing and maxim um 25 tiles h igh for a hanging con-

ﬁguration.

The maximum height of the X2.8R display in a b

ase stand conﬁguration can be reduced depending on the wind load, the friction

coefﬁcient, the position of the LED-wall, and the weight of the complete d isplay. Use the LE D-wall Ballast Calculator (version 10

or later) to de termine the maximum height of the X 2.8R display and the required ballast to prevent tipping or s liding of the X2.8R

display. The LED-wall Ballast Calculato

r is available on m y.barco.com.

R5906160 X2.8R 28/02/2018

1. Safety

Base surface

Do not install a base stand X2.8R display upon a smooth surfaces. Place rubber mats between the foot beams o f the LED wall and

the smooth surface to increase friction.

Maximum w ind load for hanging a nd stand ing conﬁguration

The X2.8R display in a hanging conﬁguration must be torn down in case winds exceeds B eaufort force 6 (>50km/hr).

1.4 Proper usage

Proper usage of X2.8R tiles

• No part of the X2.8R tile can come in contact with any type of corrosive substance.

• Using the LED product in an environment with high corrosive gasses (e.g. Sulphur) can lead to discoloration of the materials.

This discoloration gives a c hange in brightness of the product. T his could lead to uniformity differences and po ssibly also to

failures. Each us e of the product in this kind of env ironme nt nee ds to be c hecked up-front with the supplier.

• X2.8R tiles are to be used in environm ents mee ting the operating speciﬁcations.

• X2.8R tiles a re not to be used in environments that are subject to airborne con taminants such as that produced by s mok e

machines (cracked oil) or sim ilar (these deposit a thin layer of greasy residue upon the LE Ds optics, degrading performance).

• X2.8R tiles are not to be exposed to extreme localized heat or cold ex ceeding the temperature speciﬁcations.

• X2.8R tiles are not to be exposed to any element or situation that will c ause any part of the display to heat beyond wh at occurs

during normal operation. Such situations inc lude but are not limited to lasers, ultrasonic vibration, or any type of s ubstance that

prevents p roper ventilation and heat radiation of the X2.8R tiles.

• Power c onnected t o the X2.8R tiles must m eet the s peciﬁcations outlined in the installation manua l.

• Avoid any accidental bum ping of the tile corners while installing o r removing t he X2.8R tiles. S ince LED’s of the X2.8R tiles a re

mounted near by the edg es of the LED boards, w hich is unavoidable in the design of a high resolution LED-wall, the corners

of the X2.8R tiles beco me sensitive for mech anical damage. B ecaus e of that it is required to handle the X2.8R tiles with ca re

at all times.

• Never place an X2.8R tile or an X 2.8R m odule upon a surface with the LE D’s facing downwards without protection. This to

prevent damage to the LEDs and the soft lens of the LEDs.

• X2.8R tiles which are not ins talled and which are not securely stored in an X2.8R ﬂight case, m ay only be placed v ertically upon

ﬂat surfaces free of clutter. M ake s ure that the X2.8R tile does not rest upon the bottom row of LED’s but upon the provide

studs at the bottom of the rental frame.

• While removing or installing the X2.8R tile always keep the LED side of the X2.8R tile parallel with the LED side of the remaining

neighboring X2.8R tiles. This to av oid any m echanica l stress upon the c orners of the X2.8R tiles.

• No force can be applied to the LEDs. Any LEDs dam aged due to m echanical s tress are not covered by the wa rranty.

• Safety and functional features of the display cannot be defe

ated.

• It is not allowed to clim b or hang any additional equipment on the back of an X2.8R w all. Nothing is to be allowed to hang from

the cables of an X2.8R tile.

• Any failures must be immediately and appropriately dea lt with (equipment returned to Barc o). Failing equipment cannot be left

to run in a w all.

• No additional tools (hamm ers, pry-bars, etc.) are to be used to force handles or locks into place . All moving parts s hould be

managed by hand.

• Only Barco cables speciﬁed to be u sed with the X 2.8R display are to be used to connect components in the X2.8R wall. Further,

care must be taken to connect signal only according to the installation manual.

• X2.8R tiles are not to be used in the v icinity of any equipment that is not CE and UL/ETL certiﬁed.

• X2.8R tiles are not to be transported for any distance in containers other than Barco ﬂight cases or Barco single unit pa ckaging.

Further, even the use of Barco ﬂight cases or pac kaging material does not guarantee the X2.8R tiles against damage due to

excessive force of impacts. A ll warranty claim s regarding damaged X2.8R tiles due to incorrect pack ing will be rendered invalid.

• X2.8R tiles are not to be connected to any non-B arco equipm ent.

• When stacking X2.8R tiles, the quality can on ly be guaranteed w hen using Barco X2.8R f eet. Make sure the feet are leveled

according to the manual before installing X 2.8R ti

les. Im proper leveling can result in e xcessive forces on the structural compo-

nents of the X2 .8R tiles.

• When han ging X2.8R tiles, only Barco X2.8R trusses can be used and they must be installed and con nected acc ording to the

manual. Improper hanging of X2.8R tiles can result in excess ive forces on the structural components of the X2.8R tiles.

• When stacking or hanging X2.8R tiles, the guidelines outlined in the installation m anual must be followed to prevent movement

of the display (including tipping). F urther, X2.8R tiles are only to be installed ve rtically. Any tipping of a display will cause undue

stress on the structural components of the X2.8R tiles, and could even allow the X2.8R w all to fall.

• When stacking X 2.8R tiles, the X2.8R stacker mus t be used.

• When reconnecting components in an X2.8R tile, c are must be taken to ensure that cables are carefully routed according to

the installation m anual to prevent damage to t he c

ables or other parts o f the X2.8R tile.

• X2.8R tiles can be cleaned only in accordance to the procedures deﬁned in the installation manual.

• Do not hang more than 25 X 2.8R tiles (12 m) tall with the integral rigging hardware.

• The X2 .8R d isplay is an indoor product. Us e the X2.8R tiles only in a dry area away from direct sunlight, dust and moisture.

Never install and use the X2 .8R tiles in an outdoor environment.

R5906160 X2.8R 28/02/2018

1. Safety

• Barco supplies a v ariety of stacking and hanging accessories for screens up to 1 2 tiles stacked or 25 tiles hanging.

• Ensure rigging hardware is a ble to handle the weight of the entire X2.8R with appropriate safety factors.

• Handle is intended for carrying a single tile only. Do not use for safety, tie-off, climbing o r lifting.

• The small holes on the X2.8R frame can be used as a safety attachment point.

R5906160 X2.8R 28/02/2018

1. Safety

8 R5906160 X2.8R 28/02/2018

2. Installation requirements

2. INSTA LLATION REQUIREMENTS

About this chapter

This chapter enumerates the m echanical requirements for the X2.8R d isplay, the electrical requirements to power up the X2.8R

display and the system requirements to run the control s oftware efﬁciently.

WARNING: The X2.8R display is an indoor product. Use the X2.8R tiles only in a dry area away from direct

sunlight, dust an d moisture. Never install and use the X2.8R tiles in an ou tdoor environment.

Overview

• Mechanical requireme nts for the X2.8R display

• Electrical requirements for the X2.8R display

• System requirements for the Control software

2.1 Mechanical requirements for the X2.8R display

Weight

Do not underestimate the weight of a c omplete X2.8R display. Be sure that the truss installation on whic h the X 2.8R tiles have to be

installed is c apable of handling ﬁv e (5) times the complete load of the display. Note that one X2.8R tile weights up to 7 kg (or 30.4

kg p er square meter).

Levelled surface

The surface on which an X2.8R dis play has to be installed must be levelled. Nev er install an X2.8R display on an inclined surface.

Ballast

Depending on the height of the display and the pos ition of the LE D-wall upon the foot bea ms additional w e ight (ballast) will be

required. Use the Ballast calculator tool to calculate the minimum ballast you require for safe installation of your X2.8R display. T he

Ballast calculator tool is available on the secure d B arco websit

2.2 Electrical requirements for the X2.8R display

Power requirements

One X2.8R tile requ ires 100-240 VA C, 50-60 Hz. Powe r cables ar e used to link the power from tile to tile. However, one power

breaker can drive 10 tiles o n 100-120V (15A) or 14 tiles on 200-240V (16A). Every power s ource cable should be protected by a

circuit breaker or fuses rated 16 A / 250 VAC (15 A / 250 VAC in the USA and Canada) .

Low Voltage Surge Protection Device required

Due to the dam aging effects of lightning, utility switching and switching electric m otors of other us ers on the mains, this product

needs to be protected by means of a Surge Prote

ction Device. If this product is co nnected to the mains through the power box

from Barco this protection device is already inc orporated and no extra measures need to be taken. If this product is connected to

the mains through a power distribution box from another party, please ve rify that a Low Voltage Surge Protection Device according

EN61643-11 or UL 1449 is in place.

Power system

It is recommended to use a T N-S power distribution system (a pow er distribution system with a separate neutral and grounding

conductor) in order to avoid large groun d current loops due to voltage differences in the neutral c onductor. The total electrical

installation should be protected by an appropriately rated disconnect switch, circuit br eakers, over voltage protector and Ground Fault

Current Interrupters. The installation shall be done according to the local electrical installation co des. In Europe special attention

should be given to EN 60364, the standard for electrical installation of buildings. In G ermany VDE 0100 sh ould be adhered to. In

America, special attention should be given to the National Electrical Code, ANS I/NFPA 70.

Disconnect device

When the appliance inlets of the individual tiles are not accessible, the socket outlets supplying the rack shall be installed near t he

equipment and b e eas ily accessible, or a r eadily acces sible gen eral disconnect device shall be incorporated in the ﬁxed wiring.

R5906160 X2.8R 28/02/2018

2. Installation requirements

This equipme nt M UST be earthed

In order to protect ag ainst risk of electric shock, the installation should be p roperly grounded. Defeating the purpose of the grounding

type plug will expose yo u to the risk of electric shoc k.

2.3 System requirements for th e Control software

Before you begin

It is assumed you are familiar with the W indows operating s ystem at your site.

System requirements

The In ﬁnipix™ Suite software is running on the N M 100. The connected PC needs only a Google Chrome browser to connect to the

Inﬁnipix™ Suite software.

R5906160 X2.8R 28/02/2018

3. System overview

3. SYSTEM OVERVIEW

About this chapter

This chapter enumerates the fundamental elements of the X2.8R display.

Overview

• Introduction

3.1 Introduction

The fundamental elements of an X2.8R system a re:

• X2.8R tiles.

• X2.8R truss beams (optional).

• Power box (op tional equipment).

•Inﬁnipix™ manager NM100.

•Inﬁnipix™ processor N P100.

Block diagram X2.8R system:

NP100

NM100

POWER BOX

Image 3-1

1Inﬁnipix™ Suite (Web based client interface)

2Inﬁnipix™ M anager NM100: Display Management Hardware running the Inﬁnipix™ Suite

3Inﬁnipix™ Processor(s) NP100: Display Processor(s) + Source Input(s).

4 Display Module

5 Start of data path with Ethernet cable

R5906160 X2.8R 28/02/2018 11

3. System overview

6 Ethernet cable for data path redundancy

7 Ethernet cable for connections between tiles

The redundancy data cable is op tional and requires a second (redundant) NP100. T he redundancy feature helps to automatically

solve a data interruption due to a miss ing link in the data cabling. All tiles behind the interruption will receive their content via the

redundancy data line. The com plete image will be restored almost immediately.

R5906160 X2.8R 28/02/2018

4. Components of the X2.8R display

4. COMPONENT S OF T HE X2.8R DISPLAY

About this chapter

This chapter describes all the different components, peripherals and accessories, which are used in the setup of an X2.8R display.

Overview

• X2.8R tiles

• X2.8R rental truss/ﬂoor setup acc essories

• X2.8R rental base stand setup accessories

• X2.8R ﬂight case

•Inﬁnipix™ Platform

•Inﬁnipix™ Suite User Interface

• Updates

4.1 X2.8R tiles

Introduction

11 10

2 3

Image 4-1

Indication Name

Carry handle

2 Data input-output cable

Power loop-through cable (to the next tile)

4 Latch c atcher that accepts latch hook s for locking multiple t iles together horizontally w ith the ability to deﬁne a

certain curvature.

Right LED mo dule

Connection box

Stacker point

8 Safety cable LE D modu le

9 Latch catcher that accepts latch hook s for locking multiple tiles together vertically

10 Power input socket

11 Data input-output socket

X2.8R C arbon ﬁber frame

13 Left LED module

14 Latch hook

R5906160 X2.8R 28/02/2018

4. Components of the X2.8R display

Data cable

An X2 .8R data cable with a length of 68 cm is used to connect the data signal from one row of tiles to a sec ond row of tiles by

connecting the Neutrik data input-output cable and socket.

Image 4-2

A 20 m data cable is also available to c onnect the Barco N P100 with the tiles.

RJ45 Data Coupler

An RJ 45 data coupler is available to connect two X2.8R Neutrik data cables to each other.

Image 4-3

Power extension cables

Standard Neutrik Po wercon True O ne power extension cabl

es are nee ded to loop-through the power from one column to the next

column. These extension cables can also be delivered in custom lengths, upon request.

Image 4-4

14 R5906160 X2.8R 28/02/2018

4. Components of the X2.8R display

Tile status indicator

1 32

Image 4-5

Indication Name

1 Test Button

2 Power status indicator (red)

3 Data status indicator (blue)

Power/data status indicator:

Red LED Blue LED

Status exp lanation

Blinks slow ly

Off

Tile is in standby m ode

Blinks faster Off Tile is starting up norm ally after a p ower-up

Blinks Off Tile is in normal operating mode but has no data signal. No ima

ge is displayed

Blinks in sync

with blue LED

Blinks in sync

with red LED

Tile is in normal operating mode, but receives a data signal w hich is not valid (e.g. HDMI cable

is unplugged, or no signal is available on the HDMI). No image is displayed.

Off Blinks Tile is in normal operating mode and receives a v alid dat

a signal. The tile will dis play the

correct image.

Blinks Blinks

The test button has been pushed and tile shows an inter

nal test pattern. Each push of the test

button will display one of the internal test patterns, with the source image as last in line.

Off Blinks faster Rear identiﬁcation w as selected in the I

nﬁnipix Suite. O nly one tile in a full wall will be in this

mode. The selected tile will show the source image.

4.2 X2.8R rental truss/ﬂoor setup accessories

Truss setup accessories

X2.8R truss beam s are required to set u p an X2.8R display in a hanging conﬁguration. Barco offers three sizes of X2.8R t russ

beams, namely the dual (2x), tripl

e (3x) and quad (4x) truss beam. These truss beam s cover a width of respectively two, three and

four X2 .8R tiles. Each truss beam is equipped with two or m ore lifting eyes.

In order to build the X2.8R display, the tiles must be connected using m ounting p lates. Different types of moun ting plates are avail-

able.

Order number Description Indication

R9801728

X-series Truss/Floor bea

m W 1: one tile wide truss/ﬂoor beam 1

R9801729

X-series Truss/Floor beam W 2: two tile wide truss/ﬂoor beam

R9801731

X-series Truss/Floor beam W 4: four tile wide truss/ﬂoor beam

R5906160 X2.8R 28/02/2018 15

4. Components of the X2.8R display

2 3

Image 4-6

Truss/ﬂoor beam

Overview of the truss/ﬂoor beam

5 4

2 3

Image 4-7

Truss/ﬂoor beam W1

1 Latch hook for base stand setup

2 Hoisting hook for truss setup

3 X2.8R truss/ﬂ oor W1 beam

4 Latch catch for truss setup

5 Connection lock to ﬂoor or stacker foot for ba

se stand setup

4.3 X2.8R rental base stand setup accessories

Accessories

To setup the X2.8R display in a base stand conﬁgur ation additional mounting accessories are required net to the X2.8R truss/foot

beams described in "X 2.8R rental truss/ﬂoor setup ac cessories", page 15. The X2.8R rental base stand speciﬁcaccessoriesare:

• X2.8R s tacker foot (R9801743)

• X2.8R stacker proﬁle (R9801744)

These accessories are easy to install with a minimum of tools. X2.8R tiles ar e built upon X2.8R truss/foot beam in combination w ith

the X2.8R stacker foot or upon other solid foundation. F oot beams ar e most common in the rental industry.

One X2.8R stacker proﬁle captures a height of one X2.8R tile.

R5906160 X2.8R 28/02/2018

Page is loading ...

Barco X2.8R Installation guide

Barco X2.8R Installation guide

Barco X2.8R Installation guide

Related papers

Other documents