Lennox PCO14-23, PCO16-28 and PCO20-28 Ballast and Surge Protector Replacement Installation guide

Lennox
Brand
Lennox
Model
PCO14-23, PCO16-28 and PCO20-28 Ballast and Surge Protector Replacement
Category
Motorcycle Accessories
Type
Installation guide

Lennox PCO14-23, PCO16-28 and PCO20-28 Ballast and Surge Protector Replacement is a device designed to enhance the performance and safety of your air purification system. By replacing the old ballast and surge protector with this new unit, you can expect improved efficiency, longer lifespan, and better protection against electrical hazards. The installation process is straightforward and can be completed by a licensed professional installer or a service agency.

Lennox PCO14-23, PCO16-28 and PCO20-28 Ballast and Surge Protector Replacement is a device designed to enhance the performance and safety of your air purification system. By replacing the old ballast and surge protector with this new unit, you can expect improved efficiency, longer lifespan, and better protection against electrical hazards. The installation process is straightforward and can be completed by a licensed professional installer or a service agency.

Page 1
AIR CLEANERS / FILTERS Litho U.S.A.
507551-01
4/2015
PUREAIR AIR PURIFICATION SYSTEM
PHOTOCATALYTIC OXIDATION (PCO) TECHNOLOGY
INSTALLATION INSTRUCTIONS FOR PUREAIR AIR PURIFICATION SYSTEM
MODELS PCO14-23, PCO16-28 AND PCO20-28 BALLAST AND SURGE PROTECTOR
REPLACEMENT
SURGE PROTECTOR
BALLAST
Shipping & Packing List
PureAir air purification parts which includes:
Ballast and surge protector
Installation instruction
Shipping Damage
Check equipment for shipping damage. If damage is
found, immediately contact last carrier.
WARNING
Risk of property damage, injury, or death.
Installation and service must be performed by a licensed
professional installer (or equivalent) or a service agency.
WARNING
Electric shock hazard.
Can cause injury or death.
Disconnect all electrical power supplies before servicing.
Access panels must be in place during appliance
operation.
CAUTION
Sharp edges hazard.
Sharp edges can cause injuries.
Use protective gloves when grasping equipment edges.
Installation
Both the old ballast and surge protector need to be
replaced at the same time.
1. Disconnect AC power cord and remove access panel.
2. Slide out the control box assembly.
REMOVING ADVANCE BRAND
BALLAST AND LENNOX
SURGE PROTECTOR
3. Remove the four screw from the control box cover and
flip cover over.
4. Disconnect black and white wires from the power
receptacle.
5. Using a 11/32" nut driver remove washer nut at the end
of surge protector, ballast and ground wire.
6. Disconnect red, yellow and blue wire from end of
ballast by depressing push-in connector and pulling
wire out.
7. Slide the surge protector and ballast out of the lancing.
8. Install the new surge protector and ballast by sliding it
into the lancing.
9. Secure the ballast surge protector and the ground ring
terminals (green) to the control panel with the 11/32”
washer nut removed earlier.
IMPORTANT: Verify that ground ring terminals are
secure.
IMPORTANT Increase strip length of the red, yellow
and blue wires by 0.07".
Page 2
10. Connect red, yellow and blue wires to the ballast
matching colors to the drawing shown on the ballast.
IMPORTANT: Pull the wires to ensure the wires are
latched properly to the terminal.
11. Connect the white and black wires from the surge
protector to the ballast.
IMPORTANT: Pull the wires to ensure the wires are
latched properly to the terminal.
12. Connect the white and black wire with the right-angle
spade connectors from the surge protector to the
power receptacle.
13. Flip control box cover over and secure it with the four
screws.
14. Slide the control box assembly in and then re-install
the access panel.
INSTALLED
SYLVANIA BRAND
BALLAST AND
LENNOX SURGE
PROTECTOR
15. Reconnect the power cord and check the unit
operations using the installation instruction.
16. Dispose of the removed ballast and surge protector in
accordance with local codes.
  • Page 1 1
  • Page 2 2

Lennox PCO14-23, PCO16-28 and PCO20-28 Ballast and Surge Protector Replacement Installation guide

Lennox
Brand
Lennox
Model
PCO14-23, PCO16-28 and PCO20-28 Ballast and Surge Protector Replacement
Category
Motorcycle Accessories
Type
Installation guide

Lennox PCO14-23, PCO16-28 and PCO20-28 Ballast and Surge Protector Replacement is a device designed to enhance the performance and safety of your air purification system. By replacing the old ballast and surge protector with this new unit, you can expect improved efficiency, longer lifespan, and better protection against electrical hazards. The installation process is straightforward and can be completed by a licensed professional installer or a service agency.

Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents