Candy LBCTT68TCI User manual

Candy
Brand
Candy
Model
LBCTT68TCI
Category
Washing machines
Type
User manual
3
INTRODUCTION
Read this manual carefully as it offers practical advice to help you get the most from your
washing machine.
This Instruction Manual
contains everything you need to
know about the everyday
running of your machine. Keep
it for future reference.
An Installation and
Maintenance Manual is also
provided which you should
consult during the installation
and routine maintenance of
your washing machine. The
manual also contains
information about possible
working problems, advice
about the wash load, an
explanation of label symbols
and hints about how to remove
stubborn stains.
1.- CONTROL PANEL
2.- LID
3.- DRUM
4.- DETERGENT COMPARTMENT
5.- FILTER DOOR
6.- FILTER
7.- WHEEL TROLLEY
When contacting a CANDY or one of its Technical Assistance Centre
always refer to the model (see control panel) and the registration and
series numbers which are indicated at the bottom of the machine under
the lower panel or on the warranty certificate. That is to say, everything
that appears in the box.
Providing this information will ensure a faster and more efficient service.
EN
4
INDEX
GUARANTEE ................................................................................
5
TECHNICAL DATA ..........................................................................
6
OPENING THE LID – LOADING ...................................................
7
DETERGENT DISPENSER ...........................................................
8
VARIABLE CAPACITY (Mod. CTT 88 T) .......................................
9
PROGRAMME SELECTION ..........................................................
9
CONTROL DESCRIPTION
Mod. CTT 68 T ............................................................................
10
Mod. CTT 88 T ............................................................................
13
TABLE OF PROGRAMMES
Mod. CTT 68 T ............................................................................
16
Mod. CTT 88 T ............................................................................
18
page
Place the adhesive label, in the
corresponding language, in the
support that slots into the back of the
panel display.
5
GUARANTEE
1.
The appliance comes with a guarantee certificate.
2.
Complete part B and keep it in a safe place. It should
be presented to the Technical Assistance Centre in
the event of a repair being necessary along with the
legal receipt issued by the dealer on purchase.
3.
Do not forget to send part A of the Guarantee
Certificate to be validated within 15 days of purchase.
B
A
6
5
230
360
560
30
1.950
2.300
10
0,05 min.
0,8 max.
600
65
1,21
C
CTT 68 T
5
230
175
300
30
1.950
2.200
10
0,05 min.
0,8 max.
800
54
0,85
A
CTT 88 T
TECHNICAL DATA
Load capacity .......................................................................
kg.
Voltage ...................................................................................
V.
Wash motor power rating ......................................................
W.
Spin motor power rating ........................................................
W.
Electropump power rating .....................................................
W.
Heating element power rating ...............................................
W.
Max. power input ...................................................................
W.
Fuse .......................................................................................
A.
Water pressure ..................................................................
MPa
Spin speed .............................................................
r.p.m./min
Water consumption (60º C programme) ................................
lit.
Energy consumption (60º C programme)/5 kg ..................
kWh
Energy efficiency rating ..............................................................
7
OPENING THE DRUM
1.
Lift the lid (A) and open completely. Next open the drum
door following these instructions:
2.
Press catch (B) and kept it pressed down.
Press the first shutter (C) to unlock the two shutters (C)
and (D).
3.
Open the second shutter (D). Open the first shutter (C).
Place the washing in the drum.
4.
Close the first shutter (C).
Close the second shutter (D) so that the catch on the
first shutter fits correctly into the slot. Release.
5.
Ensure that both shutters are perfectly aligned and properly
closed.
IMPORTANT: IT IS IMPORTANT TO MAKE SURE THAT
THE DRUM IS CAREFULLY CLOSED BEFORE
OPERATING THE MACHINE, OTHERWISE THE
MACHINE OR LAUNDRY COULD GET DAMAGED.
2 min.
IMPORTANT: A SPECIAL
SAFETY DEVICE PREVENTS
THE LID FROM BEING
OPENED IMMEDIATELY
AFTER THE WASH HAS
FINISHED. ONCE THE SPIN
CYCLE HAS FINISHED, WAIT
FOR 2 MINUTES BEFORE
TRYING TO OPEN THE LID.
FRONT OF THE
WASHING
MACHINE
D
C
FRONT OF THE
WASHING
MACHINE
D
C
FRONT OF THE
WASHING
MACHINE
C
B
D
WASHING
MACHINE LID
A
FRONT OF THE
WASHING
MACHINE
C
D
8
DETERGENT DISPENSER
The detergent dispenser is divided into 4 compartments:
• Compartment I, is for prewash powder detergent. The recommended quantity is
60 gm of detergent (for 5 kg of laundry).
• Compartment II, is for wash powder detergent. The recommended quantity is 120
gm of detergent (for 5 kg of laundry).
• The compartment is for bleach. The recommended quantity is 7 cl.
• The compartment is for fabric conditioners, scenting agents and special
additives. The recommended quantity is 5 cl.
The detergent compartment has two guidance lines:
• RECOMMENDED (lower line). This indicates the recommended level for the prewash
and wash compartments.
• MAX. This indicates the maximum level which should never be exceeded.
MAXIMUM
(wash)
MAXIMUM
(bleach and scenting agent)
MAXIMUM
(prewash)
RECOMMENDED
9
PROGRAMME SELECTION
WHEN SELECTING A PROGRAMME, ENSURE THAT THE START/STOP BUTTON IS
NOT ACTIVATED.
To select a programme:
• Programmes are selected by means of the corresponding control knob (A). See the
table of programmes.
• Select the wash temperature by means of the corresponding control knob.
• Select the spin speed by means of the corresponding control knob.
(Mod. CTT 88 T)
• Select the different options available by pressing the corresponding buttons.
VARIABLE CAPACITY
Mod. CTT 88 T
This washing machine automatically adapts the water level to the type and quantity of clothes
to be washed. So it is possible to obtain a «customised» wash, even in terms of energy. This
system reduces water and energy consumption and provides an appreciable reduction in
wash time.
10
CONTROL DESCRIPTION
Programme selector knob ...........................................................
Temperature selector knob .........................................................
Spin exclusion button..................................................................
1/2 load button ............................................................................
ON/OFF pilot light .......................................................................
ON/OFF button ...........................................................................
A
B
D
E
G
H
CTT 68 T
11
USE OF THE SELECTION CONTROLS
A
. PROGRAMME SELECTOR KNOB
This control allows you to select the washing programmes.
ALWAYS ROTATE the control in a clockwise direction,
never in an anticlockwise direction. Do not press the “on”
button (H) before selecting the programme
.
If you wish to modify the position of the control or select
another programme once a cycle has commenced, press
the On/Off button. Press again to recommence once the
modification has been completed.
B
. TEMPERATURE SELECTOR KNOB
This control allows you to select the temperature of your
wash.
If you wish to carry out a cold wash, turn the knob until the
cold symbol coincides with the selector mark.
THE KNOB CAN BE TURNED IN BOTH DIRECTIONS.
Do not exceed the maximum temperature recommended
for each cycle in the table of programmes.
CTT 68 T
12
USE OF THE SELECTION CONTROLS
D
. SPIN EXCLUSION BUTTON
This button excludes the spin cycle from the wash programme. This option is
recommended for special fabrics.
E
. 1/2 LOAD BUTTON
The water load for a small wash may be reduced by pressing the ( ) load
button. This saves water, detergent and electricity. The amount of detergent
used should be reduced in proportion to the load.
IMPORTANT: NEVER PRESS THE HALF LOAD BUTTON WHEN
WASHING PURE NEW WOOL AND VERY DELICATE FABRICS.
G
. ON/OFF PILOT LIGHT
H
. ON/OFF BUTTON
CTT 68 T
13
CONTROL DESCRIPTION
Programme selector knob ...........................................................
Temperature selector knob .........................................................
Spin speed selector knob ...........................................................
Flot button (anticreasing) ............................................................
Super-rinse button ......................................................................
ON/OFF pilot light .......................................................................
ON/OFF button ...........................................................................
A
B
C
D
E
G
H
CTT 88 T
14
USE OF THE SELECTION CONTROLS
A
. PROGRAMME SELECTOR KNOB
With this knob you can select the wash programme as you
wish. Press the knob and turn it until the programme
(number or symbol) coincides with the marker point.
ALWAYS ROTATE the control in a clockwise direction,
never in an anticlockwise direction. Do not press the “on”
button (H) before selecting the programme
.
If you wish to modify the position of the control or select
another programme once a cycle has commenced, press
the On/Off button. Press again to recommence once the
modification has been completed.
B
. TEMPERATURE SELECTOR KNOB
With this knob you can select the washing temperature as
you wish. Press the knob and turn it until the temperature
desired coincides with the marker point.
If you wish to carry out a cold wash, turn the knob until the
cold symbol coincides with the selector mark.
THE KNOB CAN BE TURNED IN BOTH DIRECTIONS.
Do not exceed the maximum temperature recommended
for each cycle in the table of programmes.
CTT 88 T
15
CTT 88 T
USE OF THE SELECTION CONTROLS
C
. SPIN SPEED SELECTOR KNOB
This control allows you to select the speed of the final spin.
To select a speed, press the centre of the control knob to
release and turn it until the desired speed coincides with
the selector mark. When you have selected a speed, press
the control knob once again.
This knob selects the final spin speed. To select a speed,
press down and turn until the desired speed coincides with
the selector mark.
The final spin cycle reaches the maximum speed selected
in non-delicate programmes. The middle and final spin
cycles for mixed, synthetics and delicate programmes is
carried out at 400 r.p.m.
If you do not want a spin cycle, coincide the spin exclusion
symbol with the selector mark.
THE KNOB CAN BE TURNED IN BOTH DIRECTIONS.
D
. FLOT-BUTTON
This button works in all programmes except the 32-minute cycle.
When it is pressed, the machine stops on the last rinse, leaving the clothes
soaking in a full drum of water.
To complete the programme and spin the clothes, press the button again to
release it.
Don not press this button if the «energetic spin» (cotton) programme
is selected.
E
. SUPER-RINSE BUTTON
Pressing this button removes the last vestiges of soap powder from the
fabrics, as the rinses are done with more water.
G
. ON/OFF PILOT LIGHT
H
. ON/OFF BUTTON
16
MAX.
LOAD
IN KG
TABLE OF PROGRAMMES
HEAVILY SOILED
COLOUREDS
ACRYLICS
WOOL
GENTLE RINSE
GENTLE LAST RINSE
GENTLE SPIN
EMPTY
Drain off water
5
6
7
8
Z
Cold to
…60º
Cold to
…50º
Cold to
…40º
Cold to
…40º
—
—
—
—
INTENSIVE HEAVILY SOILED
NORMAL
FAST COLOUREDS
DELICATE COLOUREDS
BLEACH/WHITENER
Organic stains
VIGOROUS RINSE
VIGOROUS LAST RINSE
VIGOROUS SPIN
I
II
5
5
5
3,5
—
—
—
—
•
•
•
•
•
•
•
•
•
•
•
•
•
•
2
2
2
1
—
—
—
—
•
•
•
•
•
•
•
•
•
•
Cold to
…90º
Cold to
…90º
Cold to
…60º
Cold to
…40º
—
—
—
—
The first programmes in each group are longer and therefore ensure a more efficient wash at the same
temperature. Select the later programmes for lightly soiled or particularly delicate clothes.
Programme
*
, as per standard EN 60456.
FAST WASH PROGRAMME
32-minute cycle 2 32´
Cold to
…50º
•
PROG.
SEL.
TYPE OF
FABRIC
PROGRAMME
PRODUCTS
TEMP.
SEL.
ºC
CTT 68 T
1
2
*
3
4
17
REMARKS
1. For highly soiled clothes, use a maximum load of 3 kg.
2. In programmes 5, 6, 7 and 8 the washing machine stops with water in the drum at the
end of the rinse cycle to prevent creasing.
To finish the cycle, select programme Z to drain the drum. Another option is to select
programme: gentle spin.
Always turn the machine off with the ON/OFF button before selecting programme.
3. In programmes 1 and 2, add bleach in the appropriate compartment for automatic
whitening.
4. This machine is designed to use fabric softener in the last rinse automatically in all
washing cycles.
32-MINUTE FAST PROGRAMME
This programme runs through a complete washing cycle for up to 2 kg of
clothes at 50 ºC in just 32 minutes.
Pour washing powder/liquid into the pre-wash compartment (compartment
I).
The maximum amount of bleach which can be used is shown on the specific
indicator provided.
The 32-minute fast programme can also be used as a pre-wash cycle with
particularly heavily soiled clothes. Just select the desired main programme
afterwards.
CTT 68 T
18
NORMAL SOILING
COLOURS FAST
COLOURS DELICATES
DELICATE RINSES
DELICATE RINSE
DELICATE SPIN
DELICATES
WOLL
«Machine washable»
HAND WASH
DELICATE RINSES
DELICATE RINSE
DELICATE SPIN
WATER DISCHARGE
INTENSIVE WITH PREWASH
NORMAL SOILING
COLOURS FAST
COLOURS DELICATES
BLEACH
Organic stains
ENERGETIC RINSES
ENERGETIC RINSE
ENERGETIC SPIN
TABLE OF PROGRAMMES
SEL.
PROG.
I
II
MAX.
LOAD
IN KG
TYPE OF
FABRIC
PROGRAMME
DETERGENTTEMP.
SEL.
ºC
2
2
2
—
—
—
MIXED SYNTHETICS
RESISTANTS
5
5
5
3,5
—
—
—
—
•
•
•
•
•
•
•
•
•
•
•
•
•
•
8
9
10
Z
1,5
1
1,5
—
—
—
—
From cold
to
…40º
From cold
to
…40º
From cold
to
…30º
—
—
—
—
•
•
•
•
•
•
•
•
EXTREM. DELIC. FABRICS
5
6
7
•
•
•
•
•
•
•
•
From cold
to
…60º
From cold
to
…50º
From cold
to
…40º
—
—
—
From cold
to
…90º
From cold
to
…90º
From cold
to
…60º
From cold
to
…40º
—
—
—
—
RAPID PROGRAMME
Rapid 32 minute super cycle
32´2
From cold
to
…50º
•
•
Programme
*
, according to EN 60456 Regulations
The first program in each group is the longest and thus ensures the most effective wash at a given
temperature. The other programs should be selected for clothes which are only lightly solied or are
particularly delicate.
CTT 88 T
1
2
*
3
4
19
NOTE:
1. If the wash load is very dirty it is best to reduce the load weight to 3 kg.
2. Programmes 1, 2 have an automatic bleaching option. Simply place the bleaching agent
in the compartment.
3. The washing machine is designed to incorporate fabric softener automatically in the last
rinse of each washing cycle.
RAPID 32 MINUTE PROGRAMME
The rapid 32 minute programme enables a complete washing cycle
for a maximum 2 kg wash at a temperature of 50°C to be carried out in
30 minutes. The temperature of the wash can be reduced via the
temperature selector knob.
The soap powder must be loaded into the pre-wash dispenser
(compartment I).
The maximum amount of soap powder which can be used for this
programme is indicated by the 32 minute mark in the dispenser.
The rapid 32 minute programme can also be used as a pre-wash
cycle in the case of a heavily soiled wash, following with the main
programme as desired.
CTT 88 T
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17

Candy LBCTT68TCI User manual

Candy
Brand
Candy
Model
LBCTT68TCI
Category
Washing machines
Type
User manual
Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents