Motorola CDM1250 Installation guide

Brand: Motorola

Model: CDM1250

Category: Two-way radios

Type: Installation guide

This manual is also suitable for

Professional Series

Two-Way Radio Service & Installation Manual

CDM-Series

Control Station

Product Software License Agreement

THIS LICENSE AGREEMENT BETWEEN YOU, THE USER, AND MOTOROLA, APPLIES TO THE SOFTWARE

EMBEDDED IN OR DELIVERED WITH THE ACCOMPANYING MOTOROLA PRODUCT (“SOFTWARE”), AND IS

APPLICABLE UNLESS A SIGNED LICENSE AGREEMENT COVERING ITS SUBJECT MATTER HAS BEEN EXE-

CUTED BETWEEN YOU AND MOTOROLA. BY USING THE PRODUCT, YOU ACKNOWLEDGE THAT THIS

AGREEMENT HAS BEEN READ AND UNDERSTOOD AND THAT YOU AGREE TO BE BOUND BY ITS TERMS

AND CONDITIONS. IF YOU DO NOT AGREE, YOU ARE NOT LICENSED TO USE THE PRODUCT, AND IF YOU

ARE THE PURCHASER OF THE PRODUCT, YOU SHOULD IMMEDIATELY RETURN THE PRODUCT IN ITS

ENTIRETY TO ITS PLACE OF PURCHASE FOR A REFUND.

Motorola grants to You a non-exclusive license to use the SOFTWARE in the manner described in the documentation associ-

ated with the product. Motorola retains ownership of the SOFTWARE including all patent, copyrights, and other intellectual

property rights. You may transfer this license to use the SOFTWARE as long as the transferee agrees to be bound by the terms

of this Agreement.

You agree not to reverse engineer or create derivative works of the SOFTWARE; not to transmit the SOFTWARE electroni-

cally; not to modify, configure, or use the SOFTWARE in any manner not authorized by MOTOROLA; and, except as an inte-

gral part of the product, not to rent, lease, or convey the SOFTWARE.

MOTOROLA SHALL NOT BE LIABLE FOR INCIDENTAL OR CONSEQUENTIAL DAMAGES ARISING FROM THE

USE OF THIS SOFTWARE.

With respect to the U.S. Government, if acquired under FAR policy (52.227-19), the SOFTWARE is provided with Restricted

Rights, and if acquired under DFARS policy (227.7202), then the SOFTWARE is provided only with the commercial rights of

this Agreement.

This license is effective until terminated. It will terminate immediately and automatically if You fail to comply with any term

of this Agreement.

You agree that this is the complete and exclusive statement of the agreement between You and Motorola and that any modifi-

cation of these terms shall be made only by mutual agreement and evidenced by written amendment signed by both parties.

This Agreement shall be governed and interpreted by the laws of the State of Illinois, United States of America.

Computer Software Copyrights

This manual may not be reproduced, in whole or in part, in any form whatsoever, without the express written permission of Motor-

ola, Inc.

The Motorola products described in this manual contain one or more computer programs. These computer programs are pro-

tected by copyright law and international treaties. Unauthorized reproduction or distribution of these programs, or any part

thereof, may result in severe civil and criminal penalties, and will be prosecuted to the maximum extent possible under the law.

U.S. and international patents pending.

This product is covered by one or more issued U.S. Patents. Other Patent applications pending.

October, 2004 6880309N15-A i

Table of Contents

Foreword

Scope of Manual . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . iii

How to Use This Manual. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . iii

Other Documentation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . iii

Technical Support and Service . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . iii

Regulatory Requirements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . iii

Product Safety and RF Exposure Compliance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . iii

Electrostatic Discharge – Sensitive Parts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . iii

Accessories . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . iv

Service Aids. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .v

Test Equipment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .v

Section 1

Introduction to the

CDM Control Station

Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1

CDM Control Station . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1

Mobile Radio Compatibility . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1

Physical Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1

CDM Control Station Housing. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1

CDM Control Station Fan Assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1

CDM Control Station Power Supply . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1

CDM Control Station Interface Circuit Boards . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2

Cables . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2

Preventive Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3

Visual Inspection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3

Periodic Cleaning. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3

Section 2

CDM Control Station Operation

Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1

General Description. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1

Performance. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1

General Specifications. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1

Control Functions and Indicators . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1

Transmit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1

Monitor. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1

Intercom . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2

Supervisory. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2

Speaker Volume . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2

Audio Sources and Level Adjustments . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2

Microphone Sources. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2

Speaker. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2

Accessory RX. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2

Audio States. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2

Transmit Audio. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2

Intercom Audio . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2

RX Audio . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2

Operator Instructions. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2

ii 6880309N15-A October, 2004

Table of Contents CDM Control Station

Receiving Calls. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2

Initiating Calls . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2

Section 3

CDM Control Station Installation

Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1

General considerations. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1

Interface Module settings. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1

Switch Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1

Switch 1, Intercom/Parallel TX Audio Enable . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1

Switch 2, Intercom Audio From the Control Station to Accessory TX Port. . . . . . . . . . . . . . . . . . . . . . . . . . . . .1

Switch 3, Intercom Audio From the Control Station to Accessory RX Port . . . . . . . . . . . . . . . . . . . . . . . . . . . .1

Switch 4, Mute Accessory RX Audio During Intercom . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1

Switch 5, Intercom Audio From Local Mic . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1

Switch 6, Intercom Audio From Desk Mic. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1

Switch 7, Intercom Audio From Headset Mic. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1

Switch 8, Accessory Transmit Mutes Local Speaker . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1

Default Settings. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1

Jumper Settings. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1

Adjusting Audio Levels . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1

Additional Considerations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2

Radio Control Head Speaker . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2

Radio Programming Parameters. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2

Desk Microphone . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2

Basic Disassembly/Assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2

Disassembling the CDM Control Station Housing. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2

Removing the Housing Cover. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2

Disassembling the Inner Chassis. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2

Assembling the CDM Control Station Housing. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3

Installing the Radio . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3

Installing the Ground Stud. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3

Connecting the Power Supply. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3

Attaching the AC Power Cord. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4

Replacing the Cover . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4

Field Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4

Section 4

CDM Control Station

Theory of Operation

Audio Paths . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1

Transmit Audio. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1

Intercom/Parallel Transmit Audio . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1

Receiver Audio. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1

Digital functions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1

Mic Selection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1

PTT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1

Monitor. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1

Section 5

CDM Control Station Troubleshooting

CDM Control Station Interface Module (CSIM), Audio Section . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1

CDM Control Station Interface Module (CSIM), Digital Section. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2

CDM Control Station I/O, CSAP and CSKP. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3

CDM Control Station Circuit Board Details . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4

October, 2004 6880309N15-A iii

CDM Control Station Foreword

Scope of Manual

This manual is intended for use by experienced technicians

familiar with similar types of equipment. It contains all ser-

vice information required for the equipment described and is

current as of the printing date. Changes which occur after the

printing date are incorporated by service manual revisions.

These revisions are added to the manuals as the engineering

changes are incorporated into the equipment.

How to Use This Manual

This manual contains introductory material such as model

charts and accessories, as well as sections that deal with spe-

cific service aspects of the CDM Control Station. Refer to the

Table of Contents for a general overview of the manual, or to

the “Overview” paragraph in each section for a specific over-

view of the information in that section.

Other Documentation

Table 1 lists other documentation you may need to setup and

configure the Control Station.

Technical Support and Service

For Technical Support, please call:

Motorola Inc.

(800) 927-2744

If it is necessary to return a unit for repair or replacement, the

call-taker will issue a Return Material Authorization (RMA)

number. Include the RMA number in the package with the

defective unit.

For information on warranty service, returns or repairs,

contact:

Motorola Inc.

Radio Support Center

2204 Galvin Dr.

Elgin, IL 60123

(800) 227-6772

To order parts, contact:

Motorola Inc.

2200 Galvin Drive

Elgin, IL 60123

(800) 422-4210

Regulatory Requirements

In the United States, the FCC regulates licensing of RF frequen-

cies. The terms of the FCC radio license for a particular opera-

tion will determine the frequencies, output power, and antenna

height(s) for a given situation. The applicable “Part” of the FCC

Rules and Regulations must be consulted before a CDM Con-

trol Station is activated. In countries other than the United

States, contact the local government for licensing rules.

NOTE

In the United States of America, the CDM-

Series radios may not legally be used as the

transmit radio in a UHF (450 to 512 MHz)

repeater or base station application with 12.5

kHz channel spacing. The ±2.5-ppm fre-

quency stability capability of the radio does

not meet the requirements of part 90 of the

Rules and Regulations of the Federal Com-

munications Commission (FCC). In other

countries, check local frequency stability

requirements before placing a CDM-Series

radio based repeater or base station in opera-

tion.

Product Safety and RF Exposure

Compliance

ATTENTION!

This radio is restricted to occupational use only to satisfy

FCC RF energy exposure requirements. Before using this

product, read the RF energy awareness information and oper-

ating instructions in the Product Safety and RF Exposure

booklet enclosed with your radio (Motorola Publication part

number 68P81095C99) to ensure compliance with RF energy

exposure limits.

For a list of Motorola-approved antennas, batteries, and other

accessories, visit the following web site which lists approved

accessories: http://www.motorola.com/cgiss/index.shtml.

Electrostatic Discharge – Sensitive

Parts

This product contains CMOS and other circuit components

which may be damaged by electrostatic discharge. Proper pre-

caution must be taken when handling circuit modules. As a min-

imum, grounded wrist straps should be used at all times when

the control station cover is removed and in the handling of cir-

cuit modules.

See section 11.9 of the Motorola R56-Standards and Guidelines

for Communications Sites for more detailed information.

Table 1. Other Documentations

Information Location

CDM-Series

Operation

(North America)

CDM750 User Guide (6881091C54)

CDM1250 User Guide (6881091C55)

CDM1550 User Guide (6881091C56)

CDM-Series

Programming

(North America)

CDM-Series CPS HVN9025

CDM-Series Service

(North America)

Basic Service Manual (6881091C62)

Detailed Service Manual

(6881091C63)

Before using this product, read the

operating instructions for safe usage

contained in the Product Safety and

RF Exposure booklet enclosed with

your radio.

a u t i o

iv 6880309N15-A October, 2004

Foreword CDM Control Station

Accessories

Motorola offers several accessories to increase communications efficiency. Many of the accessories available are listed below,

but for a complete list, consult your Motorola dealer.

Desksets

L3211 MC1000 Basic Local Deskset

L3212 MC1000 DC Remote Control Deskset with 4 Freq.

L3213 MC1000 Tone Remote Control with 4 Freq.

L3167 Tone Remote Adapter; 2 Freq. with 4-Wire Audio

L3151 DC Remote Adapter; 16 Freq. with 4-Wire Audio

Microphones

HMN3000 Desk Microphone, black

HLN9573_R Shorting Plug Kit for Microphone Jack

Headsets

CDN6281A PTT Base

CDN6297A Single ear

CDN6290A Noise Canceling single ear

CDN6295A Over the ear

CDN6288A Noise Canceling over the ear

CDN6285A Over the ear w/ rear ear support for greater stability

CDN6292A Noise canceling over the ear w/ rear ear support for greater stability

CDN6287A Dual Ear

CDN6294A Noise canceling dual ear

Antennas

RDD4527 150-158 MHz, VHF 3 dB Gain

RDE4556 450-470 MHz, UHF 3.8 dB Gain

General Accessories

RRX4025 Type “N” Connector Coaxial In-line Arrestor

RRX4032 Tower Mount Hardware w/In-line Arrestor

ST788 1/2” Jacketed Heliax Coaxial Ground Clamps

HLN9457 16-Pin Accessory Connector Kit

3080517U10 Mini-UHF to N-Bulkhead RF Adapter Cable

3080137S02 Radio Interface Cable

Manuals/Software

6881091C54 CDM750 Mobile Radio User Guide

6881091C55 CDM1250 Mobile Radio User Guide

6881091C56 CDM1550 Mobile Radio User Guide

6881091C62 CDM-Series Mobile Radio Basic Service Manual

6881091C63 CDM-Series Mobile Radio Detailed Service Manual

HVN9025 CDM-Series CPS Programming

October, 2004 6880309N15-A v

CDM Control Station Foreword

Service Aids

The following table lists service aids recommended for working on the CDM Control Station.

Test Equipment

The following table lists test equipment required to service the CDM Control Station.

Motorola Part No. Description Application

HLN9214 Radio Interface Box Enables communication between the radio and the computer’s serial

communications adapter.

HSN9412 RIB Power supply Used to supply power to the RIB.

HKN9216 Computer Interface cable Connects the computer’s serial communications adapter to the RIB.

HKN9217 Program Test Cable RIB to Radio Cable

HVN9025 CDM-Series CPS Software on 3-1/2 in. diskettes.

Motorola Model No. Description Characteristics Application

R2200, R2400, or R2001 Service Monitor This monitor will substitute

for items with an

asterisk *

Frequency/deviation meter and signal genera-

tor for wide-range troubleshooting and align-

ment

*R1049 Digital Multimeter Two meters recommended for ac/dc voltage

and current measurements

*S1100 Audio Oscillator 67 to 200 Hz tones Used with service monitor for injection of PL

tones

*S1053, *SKN6009,

*SKN6001

AC Voltmeter, Power Ca-

ble for meter, Test leads for

meter

1mV to 300V, 10-Megohm in-

put impedance

Audio voltage measurements

R1053 Dual-trace Oscilloscope 20 MHz bandwidth,

5mV/cm - 20V/cm

Waveform measurements

*S1350, *ST1215 (VHF)

*ST1223 (UHF) *T1013

Wattmeter, Plug-in

Elements (VHF & UHF),

RF Dummy Load

50 Ohm, ±5% accuracy,

100 Watts, maximum

0-1000 MHz, 300 Watts

Transmitter power output measurements

S1339 RF Millivolt Meter 100uV to 3V RF, 10 kHz to

1.2 GHz

RF level measurements

*R1013 SINAD Meter Receiver sensitivity

S1347 or

S1348 (prog)

DC Power Supply 0-20 Vdc, 0-5 Amps Bench supply for 12.5 Vdc

vi 6880309N15-A October, 2004

Foreword CDM Control Station

Test Equipment

October, 2004 6880309N15-A 1-1

Section 1

Introduction to the

CDM Control Station

Overview

This section introduces you to the CDM Control Station; out-

lines major components; physical appearance; accessories;

general information about cables, and basic assembly of the

Control Station.

CDM Control Station

The Control Station provides a low cost integrated base sta-

tion package with enhanced control and audio accessory fea-

tures. The station is unique because it is designed to use off-

the-shelf mobile radios for the transceiver. This design pro-

vides the additional benefits of quick repair and minimizing

inventory. The unit is completely self-contained, with radio,

power supply and necessary electronics mounted in an

attractive desktop cabinet.

A few features that distinguish the Control Station:

• Portability

The Control Station is a self-contained, portable,

desktop unit.

• Local Desktop Control

The Control Station provides enhanced control func-

tions through conveniently located front panel but-

tons. These functions include: Intercom, Supervisor,

Monitor, and Transmit. The front panel also houses

an internal microphone to allow communication

without the aid of an external audio accessory.

• Audio Accessory Connections

The Control Station provides easily accessible audio

ports from the front panel that allow direct connec-

tion of a headset or desk microphone.

• External Accessories

The Control Station provides a 16-pin accessory con-

nector for additional peripheral components

• Fan

The Control Station has a single speed , thermal switch

controlled fan.

• Power Supply

The Control Station has a 15 Ampere, continuous

duty switch mode power supply.

Mobile Radio Compatibility

The CDM Control Station was designed to incorporate the

CDM750, CDM1250, or CDM1550 mobile radios.

Physical Description

The following paragraphs describe the physical characteris-

tics of the Control Station.

• CDM Control Station Housing

• CDM Control Station Fan Assembly

• CDM Control Station Power Supply

• CDM Control Station Interface Circuit Boards

CDM Control Station Housing

The Control Station housing provides the necessary mobile

mounting that will make up the customer's free-standing

Control Station. The Control Station is shipped from the fac-

tory with the fan assembly, control interface, and power sup-

ply already installed in the housing. Before you can assemble

the Control Station, the housing must be partially disassem-

bled as described in Section 3, CDM Control Station Instal-

lation of, this manual.

CDM Control Station Fan Assembly

The fixed-speed 12 VDC fan assembly is mounted onto the

rear wall of the Control Station cabinet. A thermal switch

from the power supply is connected to the heatsink on the

underside of the transmit radio and monitors the temperature

of the radio. The fan turns on when necessary.

CDM Control Station Power Supply

The Control Station operates using voltages generated by the

HPN9033 power supply. The power supply operates from a

115 / 230 VAC (switch selectable) power source. The power

supply provides power for the fan assembly and radio. The

power to the interface electronics is obtained from the radio's

accessory connector. The power supply has three connectors:

• One pigtail with a 2-prong "Ford" connector to mate

with the radio power connector.

• One pigtail with a 6-position connector to power the

fan.

• One IEC ac receptacle for various line cords (U.S.

Standard, 3-prong, 115 VAC cord provided).

A slide switch on the power supply allows thermal control or

continuous ON fan operation.

1-2 6880309N15-A October, 2004

Introduction to the CDM Control Station CDM Control Station

Cables

CDM Control Station Interface Circuit

Boards

The Control Station contains three circuit boards and an

internal speaker that together provide the enhanced control

functions. The Control Station Interface Module (CSIM) is

the main board located beneath the radio inside the inner

chassis and mounted using card guides. This module con-

tains all logic, control, and interface circuitry. The Control

Station Audio Panel (CSAP) is located on the housing base

just behind the front panel. It provides the physical external

audio accessory connectors. The Control Station Key Panel

(CSKP) assembly is located on the front panel and provides

the buttons and LED indicators necessary for local dispatch

operation. A speaker is mounted to the front panel of the cab-

inet which allows for monitoring of radio receive audio,

accessory intercom, and accessory transmit audio.

Cables

The coaxial cables that connect the radio to the Control Sta-

tion back panel are fabricated from RG58A/U (the cable

used with most of the mobile antenna kits). Do not use

RG58A/U as the coaxial cable that connects the antenna con-

nector of the Control Station to the antenna. The rather small

size of the RG58A/U can introduce excessive losses in the

system that will decrease the effective range of the Control

Station.

Substitute RG400/U for short lengths and RG214/U or 1/2-

inch "hardline" for the longer lengths. If the "hardline" is

used, connect the antenna connector of the Control Station to

the end of the "hardline" with a flexible jumper cable. This

will avoid undue stress on the connectors of the cables and

the Control Station.

Table 1-1 can be used to determine which feedline to choose

for a given frequency band and line length to maintain 1.5 dB

(approximately 30%) or less power loss. Table 1-2 is a list of

Motorola part numbers for the various connectors and

cables.

esk

upervisor

rcom

Monitor

Transmit

dset

CDM1550

Figure 1-1. CDM Control Station

Table 1-1. Maximum Feedline Length in Feet (Meters)

Band RG400/U RG214/U Hardline

Low (50 MHz) 55 (17) 100 (30) 300 (90)

VHF (150 MHz) 25 (7.5) 50 (15) 150 (45)

UHF (450 MHz) 15 (4.5) 25 (7.5) 90 (27)

800 MHz 10 (3) 20 (6) 70 (21)

Table 1-2. Part Numbers for

Connectors/Cables

Part Motorola Part Number

mini-UHF male connector 2884606M01

UHF male connector 2884579F04

October, 2004 6880309N15-A 1-3

CDM Control Station Introduction to the CDM Control Station

Preventive Maintenance

Preventative maintenance of the Control Station consists of

visual inspections and periodic cleaning.

Visual Inspection

Check that external surfaces of the equipment are clean, that

connecting cables are not damaged, and that connections are

firm. A detailed inspection of the interior electronic circuitry

is not needed or desired.

Periodic Cleaning

Periodically clean smudges and grime from the exterior

housing. Use a soft, non-abrasive cloth moistened in a mild

soap and water solution. Rinse the surface using a second

cloth moistened in clean water, and clean any dirt or debris

from the fan grill.

type-N male connector 2884476G01

type-N 1/2” hardline male TDN6677

type-N 1/2” hardline female TDN6678

RG58A/U coaxial cable 3000475378

RG400/U coaxial cable 3084173E01

RG214/U coaxial cable 3015068A17

1/2” hardline cable 3080329A22

8 ft. jumper cable TDN8406A*

type-N f-f adapter 5882764A01*

*Use of the type-N f-f adapter may be required to connect the jumper cable

to the main feedline.

Table 1-2. Part Numbers for

Connectors/Cables (Cont.)

Part Motorola Part Number

1-4 6880309N15-A October, 2004

Introduction to the CDM Control Station CDM Control Station

Preventive Maintenance

October, 2004 6880309N15-A 2-1

Section 2

CDM Control Station Operation

Overview

This section contains information about the control func-

tions, audio sources, audio states, programmable features

and operator instructions for the CDM Control Station.

General Description

The Control Station is an integrated base station package

designed for fixed locations. It serves as a local dispatch

point providing enhanced local control and supports com-

mon audio accessories such as a desk microphone or headset.

Performance

The Control Station was designed for the Professional Series

mobile radios. It is intended for fixed locations where protec-

tion from the elements (snow, rain, etc.) can be provided.

The station is relatively light and portable.

The fan is controlled by a thermal switch connected to the

power supply. This switching minimizes noise in office envi-

ronments while providing maximum cooling at elevated

ambient temperatures or during heavy transmit duty cycles.

The station is defined as intermittent transmit duty cycles,

but it may have surprisingly lower power slump when keyed

for long periods in an office shop environment.

General Specifications

Control Functions and Indicators

Transmit

The radio transmitter is keyed whenever PTT is activated

from one of the following sources: front panel Transmit but-

ton, desk microphone PTT, headset PTT, or PTT from an

accessory device. The Transmit LED, located above the

Transmit button on the front panel, is illuminated whenever

the transmitter is keyed in this manner.

Monitor

Before transmitting, the selected channel should be checked

for co-channel activity by using the Monitor function. RX

squelch is disabled when Monitor is asserted from any of the

following sources: front panel Monitor button, desk micro-

phone Monitor button, or Monitor from an accessory device.

The Monitor LED, located above the Monitor button on the

front panel, is illuminated whenever RX squelch is disabled

in this manner.

Dimensions 8.3” W x 13.3” L x 7.5” H

(21.1cm W x 33.8cm L x 19cm H)

approx.

Weight 11.5 lbs (5.2 kg) approx.

Power Input 10.5 to 16 V dc

Input Current Less than 1 Amp, full audio

Speaker Audio

Output

1.5 W min. into 16 ohms at reference

input

Transmit Audio

Output

80mV RMS Nominal with nominal

Mic. Inputs

Accessory Audio

Output

1 W min. into 8 ohms at reference in-

put

Headset Audio

Output

160 mV at reference input

Audio Distortion Less than 3% THD

Hum and Noise Greater than 45 dB below rated out-

puts

Audio Frequency

Response

+/- 3 dB from 300 Hz to 3000 Hz at 1

KHz ref.

User Adjustments Speaker audio level (on Radio)

Accessory RX audio output

Headset RX audio level

Intercom audio level

Ambient Tempera-

ture

0° C to 50° C

Humidity 90%, Non-condensing

Specifications Subject to change without notice.

2-2 6880309N15-A October, 2004

CDM Control Station Operation CDM Control Station

Audio Sources and Level Adjustments

NOTE

The Control Station is configured at the fac-

tory to operate with a desk microphone. If a

desk microphone is not to be used, shorting

jumper JU5 on the interface module allows

the Monitor indication LED to operate in

conjunction with a different audio source;

otherwise, the LED is ON continuously.

Intercom

The intercom function allows the operator to communicate

with desk set users in the system without transmission over

the radio channel. When the front panel user presses the

Intercom button, microphone audio from the selected source

(headset, local microphone, or desk microphone) is routed

based on switch programming.

Supervisory

The Supervisory function provides the ability to override

parallel dispatch points. The Supervisory function is latched

On or Off via the corresponding front panel buttons. When

latched On, the Supervisor ON LED is illuminated and

accessory PTT is inhibited.

Speaker Volume

The internal speaker volume is controlled by the radio's vol-

ume knob located on the radio control head.

Audio Sources and Level

Adjustments

Microphone Sources

The Control Station provides paths for transmit audio and

intercom audio. Transmit audio is defined to be microphone

audio from the base station user or a connected accessory

(local desk set, phone patch, etc.) which is broadcast on the

radio channel. Intercom audio refers to local conversations

between the accessory and base station front panel users.

Local sources of transmit/intercom audio are: a headset, desk

microphone, or the front panel microphone. Microphone

selection is accomplished via programming switches.

Speaker

Radio RX audio and Intercom/Transmit audio from the

accessory (parallel audio) are summed at the speaker. Thus,

the base station user can hear both channel audio and acces-

sory (desk set) audio. Accessory audio at the speaker can be

disabled by switch programming.

Volume of radio RX audio is adjustable using the control

knob on the mobile's control head. Volume of the accessory

intercom/transmit audio is adjustable via a pot located on the

back panel of the inner chassis.

Headset volume of radio RX audio is adjustable via a pot

located on the back panel of the inner chassis.

NOTE

Accessory (parallel) audio is routed only to

the speaker, not the headset.

Accessory RX

Accessory RX audio level is adjustable via a pot located on

back panel of the Control Station inner chassis.

Audio States

Transmit Audio

Microphone audio from the accessory is summed with

microphone audio from the local microphone source (head-

set, local microphone, or desk microphone) and fed to the

mobile microphone audio input.

Intercom Audio

When the front panel user presses the Intercom button,

microphone audio from the selected source (headset, local

microphone, or desk microphone) is routed based on switch

programming. If switch 3 is on, audio is routed to the acces-

sory RX audio port. This is necessary to allow intercom for

desk sets with no ability to monitor transmit audio.

If switch 3 is off, audio is routed to the accessory microphone

port. This is intended for desk sets that are capable of moni-

toring transmit audio.

RX Audio

Radio RX audio is routed to the speaker and the accessory

RX audio port. When the base station user is pressing Inter-

com to talk with the accessory user, the RX audio path to the

accessory can be disabled, depending on switch program-

ming.

Operator Instructions

Receiving Calls

The Control Station is normally in the receive mode upon

power-up and remains in this mode until a user transmits via

the Control Station or parallel accessory device. The Control

Station contains an internal speaker through which Receive

Audio is heard. The speaker volume is controlled by the

radio volume knob. Optionally, a headset can also be used

for receiving calls. In this case, one may wish to turn the

radio volume down to a minimal level.

Initiating Calls

To initiate a call, first depress the Monitor button and verify

that the radio channel is clear. Press and hold the Transmit

October, 2004 6880309N15-A 2-3

CDM Control Station CDM Control Station Operation

Operator Instructions

button while speaking into the microphone. Release the but-

ton to listen. Transmission is accomplished by using one of

the following microphones:

• Desk Microphone

The Control Station is configured by default to use a

desk microphone. DIP switch 6 should be in the ON

position.

• Headset

The Control Station can be configured to operate

with a headset. DIP switch 7 should be in the ON

position.

• Internal Microphone

The Control Station comes equipped with an internal

microphone intended for use in low noise environ-

ments. The local microphone is active anytime the

front panel Transmit button is pressed. DIP switch 5

should be in the ON position.

2-4 6880309N15-A October, 2004

CDM Control Station Operation CDM Control Station

Operator Instructions

October, 2004 6880309N15-A 3-1

Section 3

CDM Control Station Installation

Overview

This section contains information about the setup and instal-

lation of the CDM Control Station.

General considerations

The Control Station is a very flexible unit with various set-

tings to accommodate most installation configurations. Care

must be taken in configuring the Control Station prior to

final installation.

Interface Module settings

The Control Station Interface Module (CSIM) contains sev-

eral programmable operational features via switch settings

and jumpers. Various audio level settings are also accom-

plished with adjustment pots and jumper settings.

Switch Settings

SW1 located on the back panel of the inner chassis allows

one to specify microphone input and various audio routings.

Switch 1, Intercom/Parallel TX Audio Enable

When switch 1 is on, accessory mic (parallel) audio is routed

to the speaker, enabling Intercom and monitoring of acces-

sory transmissions by the base user.

Switch 2, Intercom Audio From the Control Station

to Accessory TX Port

When switch 2 is on, base station mic audio (from any source

– headset, local mic, or desk mic) is routed to the accessory

TX audio port. This feature is to enable Intercom and moni-

toring of base station transmissions by desk sets that are

equipped with the ability to monitor TX audio.

Switch 3, Intercom Audio From the Control Station

to Accessory RX Port

When switch 3 is on, base station mic audio (from any source

– headset, local mic, or desk mic) is routed to the accessory

RX audio port. This feature is to enable Intercom for desk

sets that are not equipped with the ability to monitor TX

audio.

Switch 4, Mute Accessory RX Audio During

Intercom

When switch 4 is on, radio RX audio to the accessory RX

Audio line will be muted during Intercom (pushing the front

panel "Intercom" button).

Switch 5, Intercom Audio From Local Mic

When switch 5 is on, the selected mic source for base station

Intercom (pushing the front panel "Intercom" button) is the

internal microphone.

Switch 6, Intercom Audio From Desk Mic

When switch 6 is on, the selected mic source for base station

Intercom (pushing the front panel "Intercom" button) is the

desk microphone.

Switch 7, Intercom Audio From Headset Mic

When switch 7 is on, the selected mic source for base station

Intercom (pushing the front panel "Intercom" button) is the

headset (if a headset is detected). If a headset is not detected

(plugged in), Intercom audio will come from the front panel

microphone.

Switch 8, Accessory Transmit Mutes Local Speaker

When switch 8 is on, the local speaker will be disabled when

an accessory device keys the radio transmitter. This is desir-

able to prevent feedback when the accessory device is located

in close proximity with the base station.

Default Settings

The Control Station ships from the factory with all switch

settings in the ON position.

Jumper Settings

Additional configuration options are available on the Con-

trol Station Interface Module (CSIM) board. The board must

be removed from the inner chassis to change the default

jumper settings. Refer to Table 3-1 for a description of the

available settings.

Adjusting Audio Levels

Although nominal audio levels have been preset at the fac-

tory, these levels should be adjusted to meet the unique

3-2 6880309N15-A October, 2004

CDM Control Station Installation CDM Control Station

Additional Considerations

requirements of each installation. These levels are set with

trim pots located on the back panel of the inner chassis.

• POT1 (IC/MON)

This potentiometer allows adjustment of the Inter-

com/Parallel audio level to the internal speaker.

• POT2 (ACC RX)

This potentiometer allows the Accessory RX audio

level to be set.

• POT3 (HEADSET)

This potentiometer provides audio level adjustment

for Radio RX to the Headset.

Additional Considerations

Radio Control Head Speaker

Since the Control Station comes equipped with an internal

speaker, it is recommended that the radio speaker (located in

control head) be disabled. This is accomplished by removing

the front panel of the control head and unplugging the

speaker lead wires.

Radio Programming Parameters

The Control Station requires that several radio parameters be con-

figured to allow proper Control Station operation.

NOTE

• Accessory Configuration/RX Audio Type

must be set for Filtered Audio.

• Accessory Pins/Pin #3 must be set for

External Mic PTT (Input).

Desk Microphone

JU1 of the Desk Microphone (HMN3000) must be installed to

allow proper base station intercom operation. The jumpers

keeps the microphone circuit active at all times, thus allowing

proper base station intercom function. Instructions for install-

ing this jumper can be found in the HMN3000 Installation

Guide, 6880903Z37.

Basic Disassembly/Assembly

NOTE

Unless specifically instructed otherwise, DO

NOT discard any hardware removed during

disassembly.

In order to conserve space in the packing box, the Control Sta-

tion housing is shipped completely assembled with the fan

assembly, top cover, power supply, and control circuitry

installed. To install the radio and configure the unit, the Con-

trol Station may have to be completely disassembled. With the

Control Station disassembled, you can begin to install the

radio and configure the Interface Module before reassembling

the housing.

Before beginning installation, remove all items from the

packing container and check them against the items refer-

enced in one of the parts lists on page 3-7. This assures that

you have received all items necessary to assembly the Con-

trol Station. Immediately report any missing or damaged

items to Motorola Product Services.

The following steps explain how to disassemble the Control

Station housing and how to reassemble it while installing the

radio and necessary cables.

Disassembling the CDM Control Station

Housing

The following steps cover the disassembly of the Control

Station housing. Refer to Figure 3-3 and Figure 3-4 on pages

3-7 and 3-8 for identification of each part and its correspond-

ing reference number.

Removing the Housing Cover

1. Place the Control Station on a flat surface.

2. Observe proper procedures for handling ESD sen-

sitive devices.

3. Remove the six (6) TT3.5mm, pan head Taptite

screws, located on the sides of the housing using a

Torx T15 driver.

4. From the front, lift the top cover up until it clears

the base, turning it on its side and placing it on the

surface at a 90 degree angle from the base.

Disassembling the Inner Chassis

Most installations will not require access to the Control Sta-

tion Interface Module (CSIM) located inside the inner chas-

Table 3-1. Jumper Settings

Jumper Function In Out (default)

JU1 Headset mic audio output level Gain added Nominal Gain

JU2 Local mic audio output level Gain added Nominal Gain

JU3 Desk mic audio output level Gain added Nominal Gain

JU4 Accessory mic audio output level Gain added Nominal Gain

JU5 Desk mic monitor logic Desk mic not installed Desk mic installed

October, 2004 6880309N15-A 3-3

CDM Control Station CDM Control Station Installation

Basic Disassembly/Assembly

sis. However, if jumper settings must be changed,

disassembly of the inner chassis will be required.

1. Remove the screw which secures the CSIM board

to the back panel of the inner chassis.

2. Remove the four (4) TT3.5mm, pan head Taptite

screws that secure the inner chassis to the base.

3. Loosen the two (2) M5mm, pan head machine

screws that secure the power supply to the inner

chassis.

4. Carefully slide the inner chassis towards the back

of the base until the pcb interface cables are acces-

sible from the front.

5. Unplug the ribbon cable from the Control Station

Audio Panel (CSAP), being careful not to break

the connector guide posts.

6. Unplug the ribbon cable from the Control Station

Key Panel (CSKP), being careful not to break the

connector guide posts.

7. Pull the CSIM board forward and disconnect the

speaker lead connector.

8. Remove the CSIM board from the inner chassis

and configure as necessary.

Assembling the CDM Control Station

Housing

The following steps enable you to reassemble the Control

Station. Refer to Figure 3-3 and Figure 3-4 on pages 3-7 and

3-8 for identification of each part and its corresponding ref-

erence number.

If the inner chassis was disassembled, reassemble at this time

by reversing the disassembly steps.

Installing the Radio

1. Slide the radio through the front panel of the hous-

ing into the inner chassis and secure with two (2)

M5mm, machine screws. The front panel radio slot

will be a tight fit as the control head is positioned

in the opening. The inner chassis uses a slotted

hole that allows the installer to adjust depth of the

radio in the chassis.

2. If you are installing the optional Internal RF Cable,

order part number 3080517U10.

3. Remove the nut and lockwasher from the cable.

4. Insert the type-N female bulkhead connector into

the "Antenna" D-hole located on the enclosure

back panel, beneath the fan. The threaded portion

of the connector will stick out the back of the cabi-

net.

5. Replace the lockwasher and nut onto the connec-

tor. Tighten to 2.26 N-m (20 in.-lbs.) torque.

6. Connect the mini-UHF connector of the cable to

the antenna connector of the radio.

7. Remove the accessory dust cover from the radio.

8. Connect one end of the radio interface cable to the

accessory connector of the radio.

9. Connect the other end of the radio interface cable

to the "Radio" connector of the CSIM, located on

the inner chassis back panel. Pay particular atten-

tion to the connector orientation in relation to the

locking tab.

Installing the Ground Stud

NOTE

The Ground Stud is factory-installed in the

Control Station.

Connecting the Power Supply

1. Locate the power supply cable with the 2-prong

"Ford" connector and connect to the DC power

connector of the radio.

2. Locate the thermal switch mounting clip supplied

with the Control Station. Slip the mounting clip

onto the thermal switch, from the power supply.

Refer to Figure 3-1.

3. Place the thermal switch and mounting clip, in-

between the long fins (5 an 6 on the antenna con-

nector side) of the radio's heatsink. Refer to

Figure 3-1.

4. Carefully push the thermal switch mounting clip

securely onto fin 6.

Figure 3-1. Professional Series Transmit Radio, Rear

View

Thermal

Switch

Radio

RF Cable

(Tx radio only)

3-4 6880309N15-A October, 2004

CDM Control Station Installation CDM Control Station

Basic Disassembly/Assembly

Attaching the AC Power Cord

1. Locate the AC power cord and a nylon tie wrap.

2. Plug the female connector of the AC power cord

into the IEC receptacle located on the back of the

power supply.

Figure 3-2. Service Loop

3. Use the tie wrap to anchor the "service loop" to the

chassis through the two holes in the bottom of

chassis as shown in Figure 3-2. Trim off the excess

tie wrap.

Replacing the Cover

1. Rotate the cover and stand on its end such that the

rear panel (with fan) is on the surface with the inside

facing the rear of the enclosure base.

2. Lower the cover onto the enclosure base by tilting

the top (as it stands) toward the front panel.

3. Align the mounting holes and ensure all cables are

inside of the unit.

4. Using a T15 Torx driver, secure the cover to the

base with the six (6) TT 3.5mm, pan head Taptite

screws removed in Step 3, "Removing the Housing

Cover".

Field Installation

To operate the Control Station, the AC line cord, antenna

feed line, ground cable, and optional accessory cable must

exit from the rear of the unit.

In addition, you must connect all of the necessary cables and

accessories as follows:

1. Attach a ground wire from an absolute earth

ground to the 1/4" threaded ground stud on the left

of the station housing.

2. Connect lightening arrestors.

3. Connect the antenna lead to the antenna connector

on the back panel of the Control Station housing.

IMPORTANT

Before connecting the AC line cord into an

AC mains outlet, ensure that the "115/230"

VAC switch on the power supply is in the

appropriate position. The switch is accessible

from the bottom of the Control Station hous-

ing.

4. Plug the AC line cord into an AC mains outlet.

Tie

Wrap

Page is loading ...

Motorola CDM1250 Installation guide

Brand: Motorola

Model: CDM1250

Category: Two-way radios

Type: Installation guide

This manual is also suitable for

Download PDF

report

Motorola CDM1250 Installation guide

This manual is also suitable for

Motorola CDM1250 Installation guide

Related papers

Other documents