ABB DNP 670 Series User manual

RELION® 650 SERIES

—

DNP, 650 series

Version 2.2

Point list manual

Document ID: 1MRK 511 419-UUS

Issued: October 2017

Revision: A

Product version: 2.2.1

Copyright

This document and parts thereof must not be reproduced or copied without written

permission from ABB, and the contents thereof must not be imparted to a third party,

nor used for any unauthorized purpose.

The software and hardware described in this document is furnished under a license and

may be used or disclosed only in accordance with the terms of such license.

This product includes software developed by the OpenSSL Project for use in the

OpenSSL Toolkit. (http://www.openssl.org/) This product includes cryptographic

software written/developed by: Eric Young ([email protected]) and Tim Hudson

([email protected]).

Trademarks

ABB and Relion are registered trademarks of the ABB Group. All other brand or

product names mentioned in this document may be trademarks or registered

trademarks of their respective holders.

Warranty

Please inquire about the terms of warranty from your nearest ABB representative.

Disclaimer

The data, examples and diagrams in this manual are included solely for the concept or

product description and are not to be deemed as a statement of guaranteed properties.

All persons responsible for applying the equipment addressed in this manual must

satisfy themselves that each intended application is suitable and acceptable, including

that any applicable safety or other operational requirements are complied with. In

particular, any risks in applications where a system failure and/or product failure would

create a risk for harm to property or persons (including but not limited to personal

injuries or death) shall be the sole responsibility of the person or entity applying the

equipment, and those so responsible are hereby requested to ensure that all measures

are taken to exclude or mitigate such risks.

This document has been carefully checked by ABB but deviations cannot be

completely ruled out. In case any errors are detected, the reader is kindly requested to

notify the manufacturer. Other than under explicit contractual commitments, in no

event shall ABB be responsible or liable for any loss or damage resulting from the use

of this manual or the application of the equipment.

Conformity

This product complies with the directive of the Council of the European Communities

on the approximation of the laws of the Member States relating to electromagnetic

compatibility (EMC Directive 2004/108/EC) and concerning electrical equipment for

use within specified voltage limits (Low-voltage directive 2006/95/EC). This

conformity is the result of tests conducted by ABB in accordance with the product

standard EN 60255-26 for the EMC directive, and with the product standards EN

60255-1 and EN 60255-27 for the low voltage directive. The product is designed in

accordance with the international standards of the IEC 60255 series and ANSI C37.90.

The DNP protocol implementation in the IED conforms to "DNP3 Intelligent

Electronic Device (IED) Certification Procedure Subset Level 2", available at

www.dnp.org.

Table of contents

Section 1 Introduction............................................................................3

This manual.............................................................................................. 3

Intended audience.................................................................................... 3

Product documentation.............................................................................4

Product documentation set..................................................................4

Document revision history................................................................... 5

Related documents..............................................................................6

Document symbols and conventions........................................................ 7

Symbols...............................................................................................7

Document conventions........................................................................ 8

Section 2 DNP3 data mappings.......................................................... 11

Overview.................................................................................................11

Point list for the IEDs.............................................................................. 11

Section 3 DNP3 protocol implementation............................................27

DNP3 device profile................................................................................ 27

DNP3 implementation table.................................................................... 71

Section 4 Glossary.............................................................................. 79

Glossary..................................................................................................79

Table of contents

650 series 2.2 ANSI 1

Point list manual

2

Section 1 Introduction

1.1 This manual

GUID-AB423A30-13C2-46AF-B7FE-A73BB425EB5F v18

The point list manual describes the outlook and properties of the data points specific to

the IED. The manual should be used in conjunction with the corresponding

communication protocol manual.

1.2 Intended audience

GUID-C9B8127F-5748-4BEA-9E4F-CC762FE28A3A v11

This manual is intended for the communication system engineer or system integrator

responsible for pre-engineering and engineering the communication setup in a

substation from an IED perspective.

The system engineer or system integrator must have a basic knowledge of

communication in protection and control systems and thorough knowledge of the

specific communication protocol.

1MRK 511 419-UUS A Section 1

Introduction

650 series 2.2 ANSI 3

Point list manual

1.3 Product documentation

1.3.1 Product documentation set

GUID-3AA69EA6-F1D8-47C6-A8E6-562F29C67172 v15

IEC07000220-4-en.vsd

P

l

a

n

i

n

g

&

p

u

r

c

h

a

s

e

E

n

g

i

n

e

r

i

n

g

I

n

s

t

a

l

i

n

g

C

o

m

i

s

i

o

n

i

n

g

O

p

e

r

a

t

i

o

n

M

a

i

n

t

e

n

a

n

c

e

D

e

c

o

m

i

s

i

o

n

i

n

g

D

e

i

n

s

t

a

l

i

n

g

&

d

i

s

p

o

s

a

l

Application manual

Operation manual

Installation manual

Engineering manual

Communication

protocol manual

Cyber security

deployment guideline

Technical manual

Commissioning manual

IEC07000220 V4 EN-US

Figure 1: The intended use of manuals throughout the product lifecycle

The engineering manual contains instructions on how to engineer the IEDs using the

various tools available within the PCM600 software. The manual provides instructions

on how to set up a PCM600 project and insert IEDs to the project structure. The

manual also recommends a sequence for the engineering of protection and control

functions, LHMI functions as well as communication engineering for IEC

60870-5-103, IEC 61850, DNP3, LON and SPA.

The installation manual contains instructions on how to install the IED. The manual

provides procedures for mechanical and electrical installation. The chapters are

organized in the chronological order in which the IED should be installed.

Section 1 1MRK 511 419-UUS A

Introduction

4 650 series 2.2 ANSI

Point list manual

The commissioning manual contains instructions on how to commission the IED. The

manual can also be used by system engineers and maintenance personnel for assistance

during the testing phase. The manual provides procedures for the checking of external

circuitry and energizing the IED, parameter setting and configuration as well as

verifying settings by secondary injection. The manual describes the process of testing

an IED in a station which is not in service. The chapters are organized in the

chronological order in which the IED should be commissioned. The relevant

procedures may be followed also during the service and maintenance activities.

The operation manual contains instructions on how to operate the IED once it has been

commissioned. The manual provides instructions for the monitoring, controlling and

setting of the IED. The manual also describes how to identify disturbances and how to

view calculated and measured power grid data to determine the cause of a fault.

The application manual contains application descriptions and setting guidelines sorted

per function. The manual can be used to find out when and for what purpose a typical

protection function can be used. The manual can also provide assistance for calculating

settings.

The technical manual contains operation principle descriptions, and lists function

blocks, logic diagrams, input and output signals, setting parameters and technical data,

sorted per function. The manual can be used as a technical reference during the

engineering phase, installation and commissioning phase, and during normal service.

The communication protocol manual describes the communication protocols supported

by the IED. The manual concentrates on the vendor-specific implementations.

The point list manual describes the outlook and properties of the data points specific to

the IED. The manual should be used in conjunction with the corresponding

communication protocol manual.

The cyber security deployment guideline describes the process for handling cyber

security when communicating with the IED. Certification, Authorization with role

based access control, and product engineering for cyber security related events are

described and sorted by function. The guideline can be used as a technical reference

during the engineering phase, installation and commissioning phase, and during normal

service.

1.3.2 Document revision history

GUID-C8027F8A-D3CB-41C1-B078-F9E59BB73A6C v4

Document revision/date

History

–/May 2017 First release

1MRK 511 419-UUS A Section 1

Introduction

650 series 2.2 ANSI 5

Point list manual

1.3.3 Related documents

GUID-94E8A5CA-BE1B-45AF-81E7-5A41D34EE112 v5

Documents related to REB650 Document numbers

Application manual 1MRK 505 388-UEN

Commissioning manual 1MRK 505 390-UEN

Product guide 1MRK 505 391-BEN

Technical manual 1MRK 505 389-UEN

Type test certificate 1MRK 505 391-TEN

Documents related to REC650 Document numbers

Application manual 1MRK 511 423-UEN

Commissioning manual 1MRK 511 425-UEN

Product guide 1MRK 511 426-BEN

Technical manual 1MRK 511 424-UEN

Type test certificate 1MRK 511 426-TEN

Documents related to RED650 Document numbers

Application manual 1MRK 505 393-UEN

Commissioning manual 1MRK 505 395-UEN

Product guide 1MRK 505 396-BEN

Technical manual 1MRK 505 394-UEN

Type test certificate 1MRK 505 396-TEN

Documents related to REL650 Document numbers

Application manual 1MRK 506 381-UEN

Commissioning manual 1MRK 506 383-UEN

Product guide 1MRK 506 384-BEN

Technical manual 1MRK 506 382-UEN

Type test certificate 1MRK 506 384-TEN

Documents related to REQ650 Document numbers

Application manual 1MRK 505 383-UEN

Commissioning manual 1MRK 505 385-UEN

Product guide 1MRK 505 386-BEN

Technical manual 1MRK 505 384-UEN

Type test certificate 1MRK 505 386-TEN

Section 1 1MRK 511 419-UUS A

Introduction

6 650 series 2.2 ANSI

Point list manual

Documents related to RET650 Document numbers

Application manual 1MRK 504 169-UEN

Commissioning manual 1MRK 504 171-UEN

Product guide 1MRK 504 172-BEN

Technical manual 1MRK 504 170-UEN

Type test certificate 1MRK 504 172-TEN

650 series manuals Document numbers

Operation manual 1MRK 500 128-UEN

Engineering manual 1MRK 511 420-UEN

Installation manual 1MRK 514 027-UEN

Communication protocol manual, DNP3 1MRK 511 413-UUS

Communication protocol manual, IEC 61850

Edition 2

1MRK 511 415-UEN

Point list manual, DNP3 1MRK 511 419-UUS

Accessories guide IEC: 1MRK 514 012-UEN

ANSI: 1MRK 514 012-UUS

Connection and Installation components 1MRK 513 003-BEN

Test system, COMBITEST 1MRK 512 001-BEN

1.4 Document symbols and conventions

1.4.1 Symbols

GUID-2945B229-DAB0-4F15-8A0E-B9CF0C2C7B15 v12

The electrical warning icon indicates the presence of a hazard which

could result in electrical shock.

The warning icon indicates the presence of a hazard which could result

in personal injury.

The caution hot surface icon indicates important information or

warning about the temperature of product surfaces.

1MRK 511 419-UUS A Section 1

Introduction

650 series 2.2 ANSI 7

Point list manual

The caution icon indicates important information or warning related to

the concept discussed in the text. It might indicate the presence of a

hazard which could result in corruption of software or damage to

equipment or property.

The information icon alerts the reader of important facts and

conditions.

The tip icon indicates advice on, for example, how to design your

project or how to use a certain function.

Although warning hazards are related to personal injury, it is necessary to understand

that under certain operational conditions, operation of damaged equipment may result

in degraded process performance leading to personal injury or death. It is important

that the user fully complies with all warning and cautionary notices.

1.4.2 Document conventions

GUID-96DFAB1A-98FE-4B26-8E90-F7CEB14B1AB6 v6

• Abbreviations and acronyms in this manual are spelled out in the glossary. The

glossary also contains definitions of important terms.

• Push button navigation in the LHMI menu structure is presented by using the push

button icons.

For example, to navigate between the options, use

and .

• HMI menu paths are presented in bold.

For example, select Main menu/Settings.

• LHMI messages are shown in Courier font.

For example, to save the changes in non-volatile memory, select Yes and press

.

• Parameter names are shown in italics.

For example, the function can be enabled and disabled with the Operation setting.

• Each function block symbol shows the available input/output signal.

• the character ^ in front of an input/output signal name indicates that the

signal name may be customized using the PCM600 software.

• the character * after an input signal name indicates that the signal must be

connected to another function block in the application configuration to

achieve a valid application configuration.

• Logic diagrams describe the signal logic inside the function block and are

bordered by dashed lines.

Section 1 1MRK 511 419-UUS A

Introduction

8 650 series 2.2 ANSI

Point list manual

• Signals in frames with a shaded area on their right hand side represent

setting parameter signals that are only settable via the PST, ECT or LHMI.

• If an internal signal path cannot be drawn with a continuous line, the suffix -

int is added to the signal name to indicate where the signal starts and

continues.

• Signal paths that extend beyond the logic diagram and continue in another

diagram have the suffix ”-cont.”

• Dimensions are provided both in inches and millimeters. If it is not specifically

mentioned then the dimension is in millimeters.

Illustrations are used as an example and might show other products

than the one the manual describes. The example that is illustrated is still

valid.

1MRK 511 419-UUS A Section 1

Introduction

650 series 2.2 ANSI 9

Point list manual

10

Section 2 DNP3 data mappings

2.1 Overview

GUID-EC7D1F5E-FFE0-4837-B02A-45E1CD531A94 v3

This document describes the available DNP3 data points and structures in the IEDs.

The data points are unmapped as a default. The point list tables represents the superset

of available DNP3 data points in these IEDs. The actual set of available points depends

on the product, optional functionalities and configuration.

The DNP3 points can be freely added, removed, reorganized and reconfigured using

PCM600.

As a default, the class assignments are Class 0 and Class 3 for binary inputs and

outputs and for double bit indications. The class assignment for analog inputs and for

counters are Class 0 and Class 2. Analog values are provided with default scalings. The

scalings can be freely modified.

The point list table only shows the signals of the first instance of each function if more

than one instance of a function can be configured.

Signals with user-defined names are listed with their default name in the point list

table.

See the engineering manual and DNP3 communication protocol manual

for more information.

2.2 Point list for the IEDs

GUID-88A55057-7A4C-4EB3-8E7A-19AD2821D5CA v4

Table 1: Signal point list

Function name

Signal type Signal name Description

Hardware input and output monitoring

BIM Binary inputs STATUS Binary input module status

BI1 Binary input 1

BI2 Binary input 2

BI3 Binary input 3

Table continues on next page

1MRK 511 419-UUS A Section 2

DNP3 data mappings

650 series 2.2 ANSI 11

Point list manual

Function name Signal type Signal name Description

BI4 Binary input 4

BI5 Binary input 5

BI6 Binary input 6

BI7 Binary input 7

BI8 Binary input 8

BI9 Binary input 9

BI10 Binary input 10

BI11 Binary input 11

BI12 Binary input 12

BI13 Binary input 13

BI14 Binary input 14

BI15 Binary input 15

BI16 Binary input 16

OSCWRN Oscillation warning

BOM Binary inputs STATUS Binary output part of BOM module status

BLOCK Block binary outputs

BO1 Binary output 1

BO2 Binary output 2

BO3 Binary output 3

BO4 Binary output 4

BO5 Binary output 5

BO6 Binary output 6

BO7 Binary output 7

BO8 Binary output 8

BO9 Binary output 9

BO10 Binary output 10

BO11 Binary output 11

BO12 Binary output 12

BO13 Binary output 13

BO14 Binary output 14

BO15 Binary output 15

BO16 Binary output 16

BO17 Binary output 17

BO18 Binary output 18

BO19 Binary output 19

BO20 Binary output 20

BO21 Binary output 21

BO22 Binary output 22

BO23 Binary output 23

BO24 Binary output 24

IOM Binary inputs STATUS Binary input part of IOM module status

BI1 Binary input 1

BI2 Binary input 2

BI3 Binary input 3

BI4 Binary input 4

BI5 Binary input 5

BI6 Binary input 6

Table continues on next page

Section 2 1MRK 511 419-UUS A

DNP3 data mappings

12 650 series 2.2 ANSI

Point list manual

Function name Signal type Signal name Description

BI7 Binary input 7

BI8 Binary input 8

BLKOUT Block binary outputs

BO1 Binary output 1

BO2 Binary output 2

BO3 Binary output 3

BO4 Binary output 4

BO5 Binary output 5

BO6 Binary output 6

BO7 Binary output 7

BO8 Binary output 8

BO9 Binary output 9

BO10 Binary output 10

BO11 Binary output 11

BO12 Binary output 12

OSCWRN Oscillation warning

General command handling from DNP master

AUTOBITS Binary outputs CMDBIT1 Command out bit 1

CMDBIT2 Command out bit 2

CMDBIT3 Command out bit 3

CMDBIT4 Command out bit 4

CMDBIT5 Command out bit 5

CMDBIT6 Command out bit 6

CMDBIT7 Command out bit 7

CMDBIT8 Command out bit 8

CMDBIT9 Command out bit 9

CMDBIT10 Command out bit 10

CMDBIT11 Command out bit 11

CMDBIT12 Command out bit 12

CMDBIT13 Command out bit 13

CMDBIT14 Command out bit 14

CMDBIT15 Command out bit 15

CMDBIT16 Command out bit 16

CMDBIT17 Command out bit 17

CMDBIT18 Command out bit 18

CMDBIT19 Command out bit 19

CMDBIT20 Command out bit 20

CMDBIT21 Command out bit 21

CMDBIT22 Command out bit 22

CMDBIT23 Command out bit 23

CMDBIT24 Command out bit 24

CMDBIT25 Command out bit 25

CMDBIT26 Command out bit 26

CMDBIT27 Command out bit 27

CMDBIT28 Command out bit 28

CMDBIT29 Command out bit 29

CMDBIT30 Command out bit 30

Table continues on next page

1MRK 511 419-UUS A Section 2

DNP3 data mappings

650 series 2.2 ANSI 13

Point list manual

Function name Signal type Signal name Description

CMDBIT31 Command out bit 31

CMDBIT32 Command out bit 32

General functions for showing signals for DNP master

MVGAPC Analog inputs IN Magnitude of deadband value

SP16GAPC Binary inputs IN1 Input 1 status

IN2 Input 2 status

IN3 Input 3 status

IN4 Input 4 status

IN5 Input 5 status

IN6 Input 6 status

IN7 Input 7 status

IN8 Input 8 status

IN9 Input 9 status

IN10 Input 10 status

IN11 Input 11 status

IN12 Input 12 status

IN13 Input 13 status

IN14 Input 14 status

IN15 Input 15 status

IN16 Input 16 status

OUTOR Output status logic OR gate for input 1 to 16

SPGAPC Binary inputs OUT Output status

Directly linked signals

ACTVGRP Binary inputs GRP1 Setting group 1 is active

GRP2 Setting group 2 is active

GRP3 Setting group 3 is active

GRP4 Setting group 4 is active

GRP5 Setting group 5 is active

GRP6 Setting group 6 is active

AEGPVOC Binary inputs TRIP Trip signal from accidental energizing of generator protection

B16I Analog inputs OUT Output value

BRCPTOC Binary inputs TRIP Operate signal of the protection logic

BTIGAPC Analog inputs OUT Output value

CCPDSC Binary inputs TRIP Trip signal to CB

CCRBRF Binary inputs CBALARM Alarm for faulty circuit breaker

TRBU Back-up trip by breaker failure protection function

TRBU2 Second back-up trip by breaker failure protection function

Table continues on next page

Section 2 1MRK 511 419-UUS A

DNP3 data mappings

14 650 series 2.2 ANSI

Point list manual

Page is loading ...

ABB DNP 670 Series User manual

This manual is also suitable for

ABB DNP 670 Series User manual

Related papers

Other documents