Star Trac 8TC-10 Installation guide

8TC-10
Star Trac
Brand
Star Trac
Model
8TC-10
Type
Installation guide

This manual is also suitable for

8-TC InsTallaTIon InsTruCTIons
2. Take TreadClimber Off PalleT
To remove the TreadClimber off the pallet; remove
the alternator shroud to expose the transport grip
handles. With two people and each gripping a han-
dle; drive the base off the rear of the pallet.
Remove and store the transport grips for later use.
3. mOunT The masT
Mount the neck mast to the base by lightly
torquing four socket head cap screws in place at the
front of the base frame.
Hardware:
o 5/16-18 X .75” Socket Head Cap Screw (Location – A)
o 5/16-18 X 1.0” Socket Head Cap Screw (Location – B)
o 5/16 Split Lock Washer
o 5/16 Flat Washer
4. COnneCT Cables
Connect the cables extruding through the lower section
of the mast into the corresponding locations on the
lower base.
5. mOunT lOwer handrails
Mount the left & right lower handrail sections to the
TreadClimber base and loosely thread four socket
head cap bolts to each handrail mount along with
sliding on the corresponding left & right handrail
grommets into place.
Hardware:
o 5/16-18 X 1.0” Socket Head Cap Screw
o 5/16 Flat Washer
o 5/16 Split Lock Washer
6. insTall lOwer rails
Slide a beauty ring onto each lower handrail section
and mount the upper handrail by loosely
threading two button head cap screws in place.
Verify that the radius cutout clears the lower securing
screw.
Hardware:
o 1/4-28 X 3/8” Button Head Cap Screw
For installation assistance or missing parts, please call Startrac Support at 1-800-503-1221
Document #620-8381 - Revision A
1. remOve all ParTs frOm The bOx
Remove all the packaging material so the TreadClimber is
ready for assembly.
7. m
OunT The disPlay rail
Install the neck beauty ring onto the top of the lower neck as
shown in detail.
Use a 1/4” Hex Allen key to install the four (4) M8x16mm
button head cap screws and four (4) 5/16” washers as
shown to secure the display rail to the lower neck. Do not
fully tighten and take care when routing cables to avoid
crimping or pinching.
8. insTall hand rails TO disPlay rail
Insert the handrail beauty rings onto the left and right
handrails. Cut in ring must be oriented as shown above
facing mast. Prior to connecting display rail, slide both side
rail covers onto siderails.
Insert the left and right handrails into the display rail then
thread four (4) 1/4”x3/8” screws into the handrails. Tighten
the handrail hardware only after display rail is connected to
both mast and handrails.
9. TighTen all assembly hardware
Once the handrails and display rail have
been installed, tighten all the hardware.
10. insTall disPlay rear hOusing
Fasten the back half of the console assembly
to the display rail using the screws supplied
with the console.
11. COnneCT Cables TO COnsOle
Connect the appropriate wires coming out
of the mast to the correct locations, please
reference the console wiring guide (Doc
620-8387) contained in the console box.
12. seCure disPlay
Secure the front half of the console assembly to the
back half using the screws supplied with the console
taking care not to pinch any wires and ensuring that
the rubber console grommet has a good seal.
Document #620-8381 - Revision A
13. POsiTiOn grOmmeTs
Dislodge the rear step shroud from the TreadClimber
base and move the handrail grommets up the
handrails.
15. mOunT COrner shrOuds
Mount the left & right corner shrouds and secure them in
place by installing the corresponding four phillips head
screws to each shroud at the circled locations.
Hardware
o #8 x1.25” Phillips Pan Head Thread Tap Screw
14. insTall rear shrOud
Mount the rear shroud to the TreadClimber base and secure it in place by installing the corresponding ve phillips
head screws to the top and lower sections at the circled locations.
Hardware:
o M5x0.8-16mm Phillips Pan Head Machined Screw
o #10-24x1/2” Phillips Pan Head Thread Tap Screw
16. mOunT sTeP shrOud
Mount the rear step shroud and wedge the
left & right handrail grommets into place. Secure the
rear step shroud by installing the corresponding ve
phillips head screws at the circled locations.
Hardware:
o M5x0.8-16mm Phillips Screw (Location – A)
o #10-24x1/2” Phillips Screw (Location – B)
17. insTall alTernaTOr shrOud and grOmmeT
Install the front alternator shroud and secure it
in place by installing the corresponding two phillips
head screws at the circled locations.Wedge the neck grommet
etween the alternator shroud and neck mast.
Hardware:
o #8-0.75” Phillips Pan Head Thread Tap Screw
19. insTallaTiOn COmPleTe Perform final testing:
1. Auto-calibrate the unit
2. Test fans
18. insTall rear feeT
With two or more people, have one person care-
fully tilt the assembled TreadClimber at an angle
by pushing up at the center of each handrail while
the second person installs the rear stabilizing feet.
  • Page 1 1
  • Page 2 2

Star Trac 8TC-10 Installation guide

8TC-10
Star Trac
Brand
Star Trac
Model
8TC-10
Type
Installation guide
This manual is also suitable for
Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents