StarTrac TreadClimber E-TCi User manual

TreadClimber

®

BY STAR TRAC

®

INSTALLATION & OWNER’S MANUAL

TREADCLIMBER by STAR TRAC - OWNER’S MANUAL | 2

TREADCLIMBER by STAR TRAC - OWNER’S MANUAL | 3

Table Of Contents

Safety Instructions 5

Precautions 5

Assembly and Setup 21

Assembly Instructions 22

Operating Instructions 32

Display Control Panel Features 33

Hot Bar® Control Features 35

Hints and Tips for Getting Started 36

Quick Start 37

Preset Programs 38

Goal-Based Programs 38

Intervals 38

Rolling Hills 38

Heart Rate Training Programs 39

Constant Heart Rate Control 39

Heart Rate Intervals 39

Cooldown Cycle 40

Using the Cooling Fan 40

Heart Rate Monitoring 40

Contact Heart Rate Monitoring 41

Chest Strap Heart Rate Monitoring 41

Setting & Testing 42

Manager Mode 42

Maintenance Mode 43

Motor Calibration 46

Troubleshooting 47

Regulatory Information 48

International Regulations 49

Maintenance 50

Daily Maintenance 50

Weekly Maintenance 50

Monthly Maintenance 50

Adjustments 51

TREADCLIMBER by STAR TRAC - OWNER’S MANUAL | 4

Introduction

This Owner’s Manual will acquaint you with the assembly, operation and maintenance of your TreadClimber

®

by STAR

TRAC cardio machine.

E-TC, E-TCi – TreadClimber

®

by STAR TRAC

We highly recommend that you read this owner’s manual prior to setting up and using your machine. The information on

the following pages will enable you to begin easily, quickly and safely.

Warning

Your TreadClimber is designed for aerobic exercise in a gymnasium or health club environment. Please check with your

physician prior to beginning any exercise program.

Do not push yourself to excess. Stop if you are feeling faint, dizzy, or exhausted. Use common sense when using this

machine. Please read the owner’s manual in its entirety before operating.

Manufacturer

Core Industires LLC, d/b/a STAR TRAC

4400 NE 77

th

Avenue, Suite 300

Vancouver, WA 98662

Telephone: (800) 228-6635, (714) 669-1660

Fax: (714) 508-3303

http://www.startrac.com

Customer Support

If any items need replacement contact the Star Trac Customer Support Department at 800-503-1221 or 714-669-1660.

STAR TRAC

®

and the Star Trac logo are registered trademarks of Core Industries.

TreadClimber is a registed trademark of Nautilus Inc. and used under licence.

TREADCLIMBER by STAR TRAC - OWNER’S MANUAL | 5

Safety Instructions

Important Safety Instructions

This product will be wired for either 120 Volts AC nominal power input OR 230 Volts AC nominal input. It is factory-equipped

with a specific electric cord and plug to permit connection to the proper electric circuit. Make sure that the product is

connected to a dedicated power line having an outlet with the same configuration as that of the plug. NO adapter should

be used with this product. If the product must be reconnected for use on a different type of electric circuit, the

reconnection should be made by qualified service personnel. Warning: If the supply cord is damaged, it must be replaced

by the manufacturer, its service agent, or similarly qualified persons in order to avoid hazard.

Save These Instructions

Attention

Star Trac recommends that units be spaced a minimum of 8 inches (200 mm) apart to allow safe and easy ingress and

egress. More importantly, there must be at least 48 inches (1.25 m) of free space behind them each unit.

As with any motorized equipment, the area where the units are located must be free of obstructions and fixtures with

sharp edges to prevent injury in the event that a user trips or loses balance and falls. Failure to follow the obstruction

free spacing requirement may result in entrapment of the user and cause significant injury. DO NOT place near wet

areas (such as pools, showers, etc.).

This chapter includes precautions and fitness safeguards for the installation and use of the TreadClimber.

These safety

notes are directed to you as the owner of the machine. Please read this chapter carefully before installing or using your

equipment and be sure to train all your members and fitness staff to follow these safety instructions. Please read this

chapter carefully before installing or using your equipment.

Safety instructions are provided in the following languages (in the order shown):

English

Dutch

French

Italian

Portuguese

Spanish

Swedish

TREADCLIMBER by STAR TRAC - OWNER’S MANUAL | 6

Precautions



CAUTION: READ THE OWNER’S MANUAL

COMPLETELY BEFORE OPERATING THIS

TREADMILL

CAUTION: BEFORE CLEANING OR SERVICING,

DISCONNECT POWER SUPPLY

CAUTION: MOVING PARTS, KEEP HANDS AND

FEET FROM UNDER THE TREADCLIMBER WHEN

OPERATING

ON

OFF

STOP (OF ACTION)

ALTERNATING

CURRENT

ON

OFF

These safety notes are directed to you as the owner of the TreadClimber

®

for safety purposes, please train all your

members and fitness staff to follow these safety instructions.



DO

Do encourage your members to discuss their health

program or fitness regimen with a health care

professional, especially if they have not exercised for

several years, are over 35, or have known health

conditions.

Do read all instructions in this manual before using

your TreadClimber.

Do use your TreadClimber only for its intended

use, as described in this manual.

Do check to ensure the belt is not moving prior to

using the TreadClimber.

Do keep the belt surface clean and dry.

Do stop operating your TreadClimber if you feel

dizzy, faint or exhausted.

Do exercise slowly until you reach a level of comfort

and security.

DO NOT

Do not let children operate your. Supervise invalids or

disabled persons who use your TreadClimber. Use the

lockout feature to prevent unauthorized or

unsupervised use.

Do not exceed the maximum allowable weight

limit (350 lbs. / 159 kg) for the TreadClimber.

Do not leave your TreadClimber unattended when it is

plugged in. Use the safety lockout feature to prevent

unsupervised use.

Do not use your TreadClimber without athletic shoes.

Do not wear loose or hanging clothing while using the

TreadClimber.

Do not step or jump on or off your TreadClimber if

the belt is moving.

Do not use or store your TreadClimber outdoors or in an

enclosed pool environment.

Do be aware of the location and proper use of the

emergency STOP key and pull cord STOP.

Do perform regular inspection and preventive

maintenance as specified in the manual.

Do not ever drop or insert any object, hands, or feet into

any opening, or underneath this equipment.

Do not place water bottles or cups on your

TreadClimber unless you are using the designated

holders for the TreadClimber

TREADCLIMBER by STAR TRAC - OWNER’S MANUAL | 7

Do keep the TreadClimber air openings free of lint, hair,

etc.

Do keep the electrical cord away from sources of

excessive heat designated holders for the

TreadClimber.

Do unplug your TreadClimber before doing any

maintenance or cleaning.

Do warm up and cool down before and after each

workout.

Do set your goals.

Do try charting your progress using the feedback

from your TreadClimber.

Do try using the incline feature to burn more calories

and strengthen your lower-body muscles.

Do be careful when mounting and dismounting the

TreadClimber. Always use the handrails, rear step and

side footsteps for support.

Do use the handrails when walking, to help your

balance and start your workout at slow speeds and

gradually increase to your desired workout level.

Do not use your TreadClimber where aerosol (spray)

products are being used or where oxygen is being

administered.

Do not use attachments or parts not recommended by

the manufacturer.

Do not use the equipment with the motor shroud

removed, or modify the equipment in any way.

Do not over tighten the running belt.

Do not operate your TreadClimber if the unit has a

damaged cord or plug. Do not use the unit if it is not

working properly, if the unit has been dropped or

damaged, or if the display console shows an error code.

Contact the Star Trac Customer Support Department at

800-503-1221 or 714-669-1660 for instructions before

retuning the unit to operation.

Page is loading ...

TREADCLIMBER by STAR TRAC - OWNER’S MANUAL | Assembly & Setup

21

Assembly & Setup

Use the following procedures to unpack and assemble your TreadClimber

®

Unpacking & Parts List

Remove the top cover from the shipping carton. Remove all parts and shipping supports (except the base) from the

carton, and verify that the following parts are included in your shipment:

Parts List:

Console Frame

Neck Mast

Handrail Grommets

Upper Handrails (Left & Right)

Handrail Beauty Rings

Lower Handrails (Left & Right)

Rear Corner Shroud (Left & Right)

Hardware Pack

Rear Shroud

Neck Grommet

Take time now to enter your TreadClimber serial number in the space below (serial number is located along the base of the

frame in the front). If parts are missing, or if you have any operational questions, please call Star Trac’s Service department

at (800) 503-1221. Have your serial number ready.

Serial No._____________________________________________

NOTE: If you are missing any of the parts listed above, inspect the packing material and the box for items that may have

been overlooked. If parts are missing, or if you have any product questions, please call Star Trac’s Service Department at

(800) 503-1221, please have your TreadClimber serial number ready.

CAUTION: Damage to the TreadClimber during assembly is not covered as part of the limited Star Trac warranty.

Note: This manual covers installation of the LED display. If you ordered a PVS kit, please refer to the assembly

and operating instructions included with that product for proper setup and operation.

Tools Required

Your TreadClimber can be assembled using the following tools:

Metric Hex Key Wrenches

Metric Open-End Wrenches

Metric Ratchet Socket Wrench

30mm Socket for Raising Rear Wheels

SetTorque Wrench

Phillips Head Screwdriver

TREADCLIMBER by STAR TRAC - OWNER’S MANUAL | Assembly Instructions 22

Assembly Instructions

2. Cut all straps to remove the cardboard packaging along

with any protective wrapping to expose the palletized

TreadClimber base (Fig. 2).

Fig. 2

1. Locate an open area to unbox the packaged

TreadClimber

(Fig.1).

Fig. 1

3. Move all unattached components off the TreadClimber

base (Fig. 3).

Hardware:

Console Frame

Neck Mast

Handrail Grommets

Upper Handrails (Left & Right)

Handrail Beauty Rings

Lower Handrails (Left & Right)

Rear Corner Shroud (Left & Right)

Hardware Pack

Rear Shroud

Neck Grommet

Fig. 3

TREADCLIMBER by STAR TRAC - OWNER’S MANUAL | Assembly Instructions

23

4. To move the TreadClimber off the pallet; remove the

alternator shroud to expose the transport grip handles.

With two people and each gripping a handle; drive the

base off the rear of the pallet (Fig. 4).

Fig. 4

5. Remove and store the transport grip handles (Fig. 5)

once the TreadClimber base is safely on the floor. The

transport grip handles can be reattached for future

transport.

Fig.5

6. Mount the neck mast (Fig. 6) to the base by lightly

torquing four socket head cap screws in place at the

front of the base frame.

Final Torque:

o 240 In-Lbs (27 Nm)

Fig. 6

TREADCLIMBER by STAR TRAC - OWNER’S MANUAL | Assembly Instructions 24

7. Connect the cables extruding through the lower section

of the neck mask into the corresponding locations on

the lower base (Fig. 7).

Fig. 7

8. Mount the left & right lower handrail sections to the

TreadClimber

base and loosely thread four socket

head cap bolts to each handrail mount (Fig. 8) along

with sliding on the corresponding left & right handrail

grommets into place.

Final Torque:

o 240 In-Lbs (27 Nm)

Fig. 8

9. Slide a beauty ring onto each lower handrail section

(Fig. 9) and mount the upper handrail by loosely

threading two button head cap screws in place. Verify

that the radius cutout clears the lower securing screw.

Final Torque:

o 35 In-Lbs (4.0 Nm)

Fig. 9

TREADCLIMBER by STAR TRAC - OWNER’S MANUAL | Assembly Instructions

25

10. Slide on the second set of beauty rings (Fig.10) onto

each upper handrail while making sure the radius

cutouts clear the available threaded holes.

Fig. 10

11. Slide the console frame onto each upper handrail

(Fig. 11) and rest the center of the console frame on

top of the neck mast plate.

Fig. 11

12. Loosely thread four socket head cap screws (Fig. 12)

with washers through the neck mast mount plate on to

the console frame mount plate.

Final Torque:

o 240 In-Lbs (27 Nm)

Fig. 12

TREADCLIMBER by STAR TRAC - OWNER’S MANUAL | Assembly Instructions 26

13. Secure the console frame to the handrails (Fig. 13) by

loosely threading two button head cap screws trough

the rail into the console frame.

Final Torque:

o 35 In-Lbs (4.0 Nm)

Fig. 13

14. Using a torque wrench, go back to steps: 6, 8, 9, 12, &

13 to thread all bolts mentioned in each step to their

corresponding final torque (Fig. 14) specifications

which are listed in the notes section of the step

instructions.

Fig. 14

15. Hover the top half of the display (Fig. 15) over the

console frame.

Fig. 15

TREADCLIMBER by STAR TRAC - OWNER’S MANUAL | Assembly Instructions

27

16. Mate all the applicable electrical connections to the

back of display electronics board (Fig. 16).

Fig. 16

17. Slide the left & right display alignment studs (Fig. 17)

into the corresponding console frame guide holes to

rest the top half of the display on to the console frame.

Fig. 17

18. From the back of the display (Fig. 19), connect the

display’s grounding wire to the frame using a washer &

Phillips head screw (Fig. 18).

Fig. 18

Fig. 19

TREADCLIMBER by STAR TRAC - OWNER’S MANUAL | Assembly Instructions 28

19. Secure the display to the console frame by installing

six Phillips head screws with washers (Fig. 18) at the

corresponding circled locations (Fig. 20).

Fig. 20

20. Mate the back shroud of the display with the rest of the

assembly by installing eight Phillips head screws at the

corresponding circled locations (Fig. 21).

Fig. 21

21. Dislodge the rear step shroud from the TreadClimber

base (Fig. 22) and move the handrail grommets up the

handrails.

Fig. 22

TREADCLIMBER by STAR TRAC - OWNER’S MANUAL | Assembly Instructions

29

22. Mount the rear shroud to the TreadClimberbase and

secure it in place by installing the corresponding five

Phillips head screws to the top (Fig. 23) and lower

(Fig. 24) sections at the circled locations.

Fig. 24

Fig. 23

23. Mount the left & right corner shrouds (Fig. 25) and

secure them in place by installing the corresponding

four Phillips head screws to each shroud at the circled

locations.

Fig. 25

24. Mount the rear step shroud (Fig. 26) and wedge the left

& right handrail grommets into the available open

space between the shrouds. Secure the rear step

shroud by installing the corresponding five Phillips

head screws at the circled locations.

Fig. 26.

TREADCLIMBER by STAR TRAC - OWNER’S MANUAL | Assembly Instructions 30

25. Install the front alternator shroud (Fig. 27) and secure it

in place by installing the corresponding two Phillips

head screws at the circled locations.

Fig. 27

26. Wedge the neck grommet (Fig. 28) between the

alternator shroud and neck mast.

Fig. 28

27. With two or more people, have one person carefully

tilt

the assembled TreadClimber (Fig. 29) at an angle by

pushing up at the center of each handrail while the

second person installs the rear stabilizing feet.

Fig. 29

TREADCLIMBER by STAR TRAC - OWNER’S MANUAL | Assembly Instructions

31

28. Transport/push (Fig. 30) the TreadClimberto its final

location by rolling it into position.

Fig. 30

29. Dislodge the rear step plugs (Fig. 31) to expose the

wheel jacking bolts. Turn the bolts in a counter clock

direction to retract the rear wheels into the base and

rest the machine on the rear stabilizing feet.

Fig. 31

30. Wedge the cover plugs back into the rear step shroud

once the TreadClimber is resting on the stabilizing feet.

31. Plug the power cord into the power & connections

panel located at the front of the machine (Fig. 32).

Fig. 32

32. Power on the machine and enter into “Maintenance Mode” to process a “Motor Calibration” procedure.

Once “Motor Calibration” is complete; the TreadClimber is ready for initial use.

TREADCLIMBER by STAR TRAC - OWNER’S MANUAL | Operating Instructions 32

Operating Instructions

Operating the TreadClimber

®

is very easy. Simply step onto the treadles, securely attach the pull cord STOP to

an article of your clothing, press QUICK START, and begin walking. The belt will begin at 0.5 mph (0.8 km/h) and

the level will be on level 1

IMPORTANT: Before operating the unit, you must be familiar with the following equipment limitations and safety

features.

Maximum Weight: Your TreadClimber is designed for a maximum user weight of 350 lbs/159 kg. DO NOT

exceed the maximum user weight.

S

TOP

SWI

TCH

ON / OFF POWER BREAKER

Emergency Stop: In case of emergency, press the STOP on the Hot Bar or pull the Pull Cord Stop on the Hot

Bar.

Immobilizing the Running Belt: To power the unit, set the ON/OFF power breaker to the ON position. To turn

the unit off, set the ON/OFF power breaker to the OFF position. When the unit is turned off, movement of the

running belt is prevented.

Safety Lockout Feature: Allows you to lock out the TreadClimber. When locked, the display shows the message

"LOCKED, ENTER ID TO UNLOCK". The user must press "0", enter a 5-digit ID number (default=12345), then

press ENTER to unlock the unit. Unit will then operate as normal (NOTE: The unit will lock back up if it is idle for

30 seconds). Use the LOCK OUT option in MAINTENANCE SETTINGS to enable/disable the lock out feature;

use the LOCKOUT ID option to change the default ID (see Settings & Testing).

TREADCLIMBER by STAR TRAC - OWNER’S MANUAL | Operating Instructions

33

DISPLAY CONTROL PANEL FEATURES

Your TreadClimber is equipped to provide you and your users unlimited exercise opportunities. Experiment with its

features to find the right combination for your fitness regimen. The Display panel shown on the following provides

the operating controls and display elements described in the following:

QUICK START Key: Starts your TreadClimber moving using a default weight of 155 lbs / 70 kg and a

time limit of 99 minutes. QUICK START will allow you to manually operate the unit. The QUICK START

key also

serves as an “Enter” key in programming modes.

STOP Key: Pauses your workout when pressed once. Ends your workout when pressed twice.

Graphic Display: Traces your progress

through each of the programs and allows you

to anticipate changes in terrain. Display

elements illuminate from left to right across

the bottom of the display to indicate your

progress through the course. At each step,

display elements illuminate in columns to

indicate your ascent up the gradient that is in

effect.

Speed Keys: During Program setup, press the or keys, respectively, until the desired

speed appears in the Information Window, then, press START or key. During a Program, press

the or keys, respectively, to increase or decrease belt speed in 0.1 miles per hour (mph)

or 0.1 kilometers per hour (km/h) increments. Speed cannot be higher than the established

“MAXIMUM SPEED” parameter. These keys repeat when pressed and held.

Speed Window: Shows the speed at which the user is walking/running.

Incline Level Keys: Adjust the amount of up and down movement of the treadles from 1 (minimum) to 5

(Maximum). These keys repeat when pressed and held.

Incline Level Window: Shows the incline level from 1 to 5.

Numeric Keypad: Allow you to enter specific values for program parameters during program setup.

The numeric keypad can also be used to adjust TreadClimber

®

speed while the TreadClimber is

operating.

OK Key: Selects/Enters values and programs during set-up.

Time Window: Shows the total time you have walked so far.

Distance Window: Shows the total number of miles or kilometers you have walked thus far.

Page is loading ...

StarTrac TreadClimber E-TCi User manual

StarTrac TreadClimber E-TCi User manual

Related papers

Other documents