Filtrete 5627902 WF SYS 4WH-QCTO-S01 CTO Operating instructions

Type
Operating instructions

Filtrete 5627902 WF SYS 4WH-QCTO-S01 CTO Whole House Large Capacity Water Filtration System is designed to provide clean, fresh water for your entire home. With its high-capacity design, this system can handle the needs of even the largest homes. The advanced CTO (Chlorine Taste and Odor) filtration technology effectively removes chlorine, sediment, and other impurities, leaving you with water that tastes great and is safe for drinking, cooking, and bathing.

Key Features:

  • High-capacity design for large homes
  • CTO filtration technology removes chlorine, sediment, and other impurities

Filtrete 5627902 WF SYS 4WH-QCTO-S01 CTO Whole House Large Capacity Water Filtration System is designed to provide clean, fresh water for your entire home. With its high-capacity design, this system can handle the needs of even the largest homes. The advanced CTO (Chlorine Taste and Odor) filtration technology effectively removes chlorine, sediment, and other impurities, leaving you with water that tastes great and is safe for drinking, cooking, and bathing.

Key Features:

  • High-capacity design for large homes
  • CTO filtration technology removes chlorine, sediment, and other impurities
High Performance
WHOLE HOUSE SYSTEMS
Large Capacity
Installation and Operating Instructions for
Homeowner: Please retain for operational
and future maintenance instructions.
4WH-QS-S01
4WH-QCTO-S01
MANUAL
34-8709-5746-0
(0412)
2
•ReadandfollowUseInstructionsbefore
installation and use of this system.
•Installationmustcomplywithexistingstateor
localplumbingcodes.
•Installoncoldwaterlinesonly.
•Donotinstallonhotwatersupplylines.The
maximumoperatingwatertemperatureofthis
filter system is 100°F (38°C).
•Protectlterfromfreezing.Drainlterwhen
roomtemperaturedropsbelow40°F(4.4°C).
•Donotinstallwhereambienttemperatures
maygoabove110°F43°C).
•Donotinstallifwaterpressureexceeds125psi
(862kPa).Ifyourwaterpressureexceeds80
psi,youmustinstallapressurelimitingvalve.
Contactaplumbingprofessionalifyouare
uncertainhowtocheckyourwaterpressure.
•Donotinstallwherewaterhammerconditions
mayoccur.Ifwaterhammerconditionsexist
youmustinstallawaterhammerarrester.
Contactaplumbingprofessionalifyouare
uncertainhowtocheckforthiscondition.
•Ensurethatthelocationandfastenerswillsupportthe
weightofthesystemwheninstalled.
•ThedisposablelterMUSTbereplacedatleast
every12months,attheratedcapacityorsoonerifa
noticeablereductioninowrateoccurs.
•Donotinstallnearwaterpipeswhichwillbein
pathofadrillingtoolwhenselectingthepositionto
mountthebracket.
•Mountlterinsuchapositionastopreventitfrombeing
struckbyotheritemsusedintheareaofinstallation.
•Ensurealltubingandttingsaresecureandfreeofleaks.
•Donotinstallindirectsunlightoroutdoors.
•Whereabackowpreventiondeviceisinstalledon
awatersystem,adeviceforcontrollingpressure
duetothermalexpansionmustbeinstalled.
•Onplasticttings,neverusepipesealantor
pipedope.UsePTFEthreadtapeonly,pipe
dope properties may deteriorate plastic.
•Donotuseatorchorotherhightemperaturesourcesnear
ltersystem,lters,plasticttingsorplasticplumbing.
•SHUTOFFFUELSUPPLYTOWATERHEATER
afterwaterisshutoff.
SAFETY INFORMATION
Read, understand, and follow all safety information contained in these instructions
prior to installation and use of the Filtrete
High Performance Whole House Large
Capacity Systems. Retain these instructions for future reference.
WARNING
WARNING
CAUTION
To reduce the risk associated with ingestion of contaminants:
•Donotusewithwaterthatismicrobiologicallyunsafeorofunknownqualitywithoutadequate
disinfectionbeforeorafterthesystem.
To reduce the risk associated with a hazardous voltage:
•Ifthehomeelectricalsystemrequirestheuseofthecoldwatersystemasanelectricalsafetyground,ajumperwire
mustbeusedtoensureasufcientgroundconnectionacrossthesysteminstallationpiping–referinstallationto
qualiedpersonnel.
•Donotinstallnearelectricwiringwhichmaybeinthepathofadrillingtoolwhen
selectingthepositiontomountthelterbracket.
•Agroundingstrap,bridgingthelterhead,mustbeinstalledoncopperpipeinstallationstomaintainelectrical
grounding,unlessacopperbypassloopisinstalled.
To reduce the risk of physical injury:
•Depressurizesystemasshowninmanualpriortohousingremoval.
EXPLANATION OF SIGNAL WORD CONSEQUENCES
Indicatesapotentiallyhazardoussituation,which,ifnotavoided,could
resultindeathorseriousinjuryand/orpropertydamage.
Indicatesapotentiallyhazardoussituation,which,ifnotavoided,may
result in property damage.
Intended use:
The Filtrete
HighPerformanceWholeHouseLargeCapacitySystemsareintendedforuseinlteringpotable
waterinhomesandhavenotbeenevaluatedforotheruses.Thesystemistypicallyinstalledatthepointofentryin
autilityormechanicalroomandmustbeinstalledaccordingtotheseinstallationinstructions.
CAUTION
To reduce the risk associated with property damage due to water leakage:
IMPORTANT NOTES:
•Failuretofollowinstructionswillvoidwarranty.
•Allowaminimumof12"clearspaceunder filter to facilitate change.
•Installwiththeinletandoutletportsaslabeled.Makesurenottoreverseconnections.
•Somelocalcodesmayrequiretheuseofalicensedplumberorcertiedinstallerwhendisruptingapotablewaterline.
Installer:Pleaseleavethismanualwithowner/operator.
Homeowner:Pleaseretainforoperationandfuturemaintenanceinstructions.
IMPORTANT NOTES:
Installation schematic is based on suggested materials. Installation of this filter can be modified by using various adapters,
or alternative connection methods and fittings to accommodate larger or smaller copper pipe or plastic tubing.
PARTS AND MATERIALS: (included)
• Filter Head (A)
• Filter Cartridge (B)
• Filter change indicator (C)
GETTING STARTED
A. B. C.
3
Master
Shut-Off
Valve
Main
Valve
Main
Valve
To Household
Plumbing
Pump
Master
Shut-Off
Valve
To Household
Plumbing
Pressure
Tank
00 0 0 6 9
Gallons
2700
3000
Model BRP
20
10
30
40
50
70
80
90
0
Badger Meter
300
600
1600
1800
12002100
2400
Water
Meter
Figure 1
4
TOOLS AND MATERIALS REQUIRED: (Not included)
Gather the required tools and materials before beginning installation. Read and follow the instructions provided with any tools listed here.
A) Pipe Cutter
B) Two 3/4" FIP sweat connections
C) 3/4" Ball Valve (Sweat Type) (3 total)
D) Plumbers Tape
E) Two Adjustable Wrenches
F) Torch
G) Plumbing Solder
H) Plumbing Flux
I) 3/4" pipe, copper
J) Two 3/4" elbows
K) Two 3/4" x 3/4" x 3/4" tees
L) Three 3/4" unions
M) Mounting hardware
N) Safety Glasses
O) Bucket
P) Towel
City Water Installation
Well Water Installation
CAUTION
To reduce the risk associated with property damage due to water leakage:
• Installation and use MUST comply with all state and local plumbing codes.
A
B
C
D
F
J
K
L
M
N
O
P
G
H
I
E
SOLDERING PASTE
FLUX
Figure 2
Valve #2
Valve #1
Valve #3
Plumbing Assembly of Bypass and Filtration System
5
CAUTION
Instructions below reference Figure 2.
1. Plan system location, support, layout and size.
2. Shut off main water supply. Depressurize water lines by opening a faucet downstream.
3. Using pipe cutters, remove a section of pipe in the install location corresponding to the size of the predetermined system assembly.
Keep a bucket and towel handy to catch and wipe up any water that drains from the line while cutting.
4. Assemble and install system as shown, observing correct ow direction of manifold. Use three shut-off valves and one ltration unit as shown.
Use copper pipe and sweated connections to assemble system. Support system by fastening bracket to wall or other framing. Alternatively, pipe
hangers may be installed on both sides of the filter head.
5. Insert lter into lter head. Push lter up, then turn one quarter of a turn to the right until it stops.
6. Ensure valve 1 and faucet downstream are open. Close valves 2 and 3. Turn on water supply, check for leaks.
7. While water is running through faucet, close valve 1, open valves 2 and 3. Allow lter to ll up.
8. Close valve 3, check for leaks again. If leaks, see Troubleshooting Section. If no leaks occur, open valve 3, let water run,
ushing air from the system for 10 gallons.
9. Close faucet.
10. Activate lter change indicator according to instructions on page 7.
To reduce the risk associated with property damage due to water leakage:
• On plastic ttings, never use pipe sealant or pipe dope. Use PTFE thread tape only, pipe dope properties may deteriorate plastic.
• Take care when using pliers or pipe wrenches to tighten plastic ttings, as damage may occur if overtightening occurs.
IMPORTANT INSTALLATION INSTRUCTIONS
6
CAUTION
To reduce the risk associated with property damage due to water leakage:
• The disposable lter MUST be replaced every 12 months or at the rated capacity or sooner if a noticeable reduction in ow rate occurs.
Water Leaks at Fittings:
Repeatinstallprocedure.
If Leaks Persist:
Checksolderjoints,unionsandlterheadconnections.Shutoffwateratthemainwatersupplyshut-off
valve,removethreadedttings,stripoffexistingPTFEtapeandapplynewtapeinaclockwise(totheright)direction
andscrewbackontoheadassembly.
Distributedby:
3M,HomeEnvironmentMarketsDivision
3MCenter,St.Paul,MN55144-1000
1-800-388-3458
Filter life depends on local water conditions and the volume of water
used. We recommend you change your lter at the rated service interval
or earlier if a noticeable reduction in ow rate occurs.
Note: Before changing lter, turn off water supply. Place a bucket
under filter to catch the small amount of water that will run out after
filter removal.
1. Close shut-off valve before lter head. Depressurize water lines by opening a
faucet downstream until water ow stops. Leave faucet open. Close shut-off
valve after filter head.
2. With both hands, turn lter one quarter of a turn to the left until it releases
from the filter head.
3. Insert new lter into lter head, turn one quarter of a turn to the right until it
stops. Ensure the lock icons line up with the hash mark on the lter head.
4. Open shut-off valve after lter head. Open shut-off valve before lter head.
Let water ush for 10 gallons (approx. 15 minutes).
5. Close faucet and check for leaks.
Replacementlterscanbepurchasedatoriginalpointofsale.
Availableltersinclude4WH-QS-F01forsedimentltrationand
4WH-QCTO-F01 for chlorine taste and odor and sediment filtration.
FILTER REPLACEMENT INSTRUCTIONS
TROUBLESHOOTING GUIDE
Step 2
Step 3
LIMITED WARRANTY:
3MwarrantsthisProductwillbefreefromdefectsinmaterialandmanufactureforone(1)yearfromthedateofpurchase.Thiswarrantydoesnotcoverfailures
resultingfromabuse,misuse,alterationordamagenotcausedby3Morfailuretofollowinstallationanduseinstructions.Nowarrantyisgivenastothe
servicelifeofanyltercartridgeormembraneasitwillvarywithlocalwaterconditionsandwaterconsumption.3MMAKESNOOTHERWARRANTIESOR
CONDITIONS,EXPRESSORIMPLIED,INCLUDING,BUTNOTLIMITEDTO,ANYIMPLIEDWARRANTYORCONDITIONOFMERCHANTABILITYORFITNESS
FORAPARTICULARPURPOSEORANYIMPLIEDWARRANTYORCONDITIONARISINGOUTOFACOURSEOFDEALING,CUSTOMERORUSAGEOF
TRADE.IftheProductfailstosatisfythisLimitedWarrantyduringthewarrantyperiod,3MwillreplacetheProductorrefundyourProductpurchaseprice.
Thiswarrantydoesnotcoverlabor.TheremedystatedinthisparagraphisCustomer’ssoleremedyand3M’sexclusiveobligation.
Thiswarrantygivesyouspeciclegalrights,andyoumayhaveotherrightswhichmayvaryfromstatetostate,orcountrytocountry.Foranywarrantyquestions,
pleasecall1-800-388-3458ormailyourrequestto:WarrantyClaims,3M,CustomerCareCenter,3MCenter225-3S-06,St.Paul,MN55144-1000.Proofof
purchase(originalsalesreceipt)mustaccompanythewarrantyclaim,alongwithacompletedescriptionoftheProduct,modelnumberandallegeddefect.
LIMITATION OF LIABILITY:
3Mwillnotbeliableforanylossordamagearisingfromthis3MProduct,whetherdirect,indirect,special,incidental,orconsequential,regardlessofthelegal
theoryasserted,includingwarranty,contract,negligenceorstrictliability.Somestatesandcountriesdonotallowtheexclusionoflimitationofincidentalor
consequentialdamages,sotheabovelimitationorexclusionmaynotapplytoyou.
Filtreteand3Maretrademarksof3MCompany.NSFisa
trademarkofNSFInternational.Timestripistheregistered
trademarkofTimestripUKLimited.
©2012,3M.Allrightsreserved.
7
Mail Product Registration Form to:
3M, Customer Care Center
3M Center 225-3S-06
St. Paul, MN 55144-1000
Product Name: Model: Date Code:
Dr. Mr. Ms. Mrs. Miss
First Name Last Name
Street Address Apt. #
City State Zip Code
Email Address
*
Phone Number
Date of Purchase
PRODUCT REGISTRATION FORM
3M, Home Environment Markets Division
3M Center, St. Paul, MN 55144-1000
1-800-388-3458
*Submitting your email address is optional. This information will be used only to provide you with information about 3M products and in
accordance with 3M’s privacy policy found at www.3M.com/privacy.
1.Presslterchangeindicatorbubblermlytoactivate.
2.Removeadhesivebackingandplacethelterchangeindicatoronthesystemhousingorinanoticeablelocation,
such as your refrigerator door.
3.Donotplacelterchangeindicatorinrefrigerator.
Activate Filter Change Indicator
Toreducetheriskassociatedwithchoking,donotallowchildrenunder
3 years of age access to the filter change indicator.
Toreducetheriskofpropertydamage,donotpuncturelterchange
indicatorbubble.Thenon-toxicuidmaystaincertainmaterials.
WARNING
CAUTION
Push to activate
Solid line will appear
and begin to ll within
a couple of minutes
12 months
Replace the lter
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14

Filtrete 5627902 WF SYS 4WH-QCTO-S01 CTO Operating instructions

Type
Operating instructions

Filtrete 5627902 WF SYS 4WH-QCTO-S01 CTO Whole House Large Capacity Water Filtration System is designed to provide clean, fresh water for your entire home. With its high-capacity design, this system can handle the needs of even the largest homes. The advanced CTO (Chlorine Taste and Odor) filtration technology effectively removes chlorine, sediment, and other impurities, leaving you with water that tastes great and is safe for drinking, cooking, and bathing.

Key Features:

  • High-capacity design for large homes
  • CTO filtration technology removes chlorine, sediment, and other impurities

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI