Side panels installation
1
2
Push to release
Loose the screw and pull the
latch to release the side panel.
Remove the side panel.
Removable fan filter
Loosing the two thumb screws on the fan module to release.
Removable
air filter
Removable air filter
C50.V1010.00E-1
Brake for
wheels
Metal casters
Power fix
bracket
Slot bracket
3-speed fan
controller
Side panel
lock
14cm fan
module
1
Chip set cooler installation Rubber protector for aluminum
wheels
Air vent
2
Adding a lock to secure the
hardware.
Support liquid cooling
system
Loosen the screws to remove
dust-free cover for water tube
openings.
Hardware list
1. Fasten the HDD screws with
anti-vibration rubber rings to the
HDD.
2. Slide the HDD into the HDD cage
with the anti-vibration kit.
Press down the HDD into the slots
to secure.
Adding extra screw to
the HDD cage for extra
security.
Note:
Extension cable 12V(1)
for power supply to M/B
Power supply
holder kit(2)
PCI card holder-S(3)
PCI card holder-L(4)
Thumb screw(7)
for PCI card holder
Chip set cooler(1)+
themb screw(2)
to mount on
PCI card holder
(6)
(56)
Thumb screw(6)
1
for stand off
2
Rubber protectors(4)
for wheels
Buzzer(1)
Stand off bolt(16)
Mounting bracket
for SSI CEB/EEB
for stand off bolt
for HDD extra fixing
Thumb screw(26)
& rubber ring(26)
for fix HDD
for cable management
VGA Card Pillar Installation Guide
2
3
4
1
6
6
4
2
10
8
4
2
8
10
6
2
4
10
8
USB
5
5
3
1
9
7
1394
3
1
7
9
5
1
3
9
7
USB
4
2
10
6
8
3
1
9
5
7
HD AUDIO
AC'97
10
9
8
6
7
5
2
4
1
3
MIC
EAR
Blue(PORT2 L)
Black(SENSE SEND)
Yellow(PORT2 R)
Brown(PORT1 R)
Red(PORT1 L)
Green(SENSE2 RETUR)
KEY
Orange(SENSE1 RETUR)
Black(PRESENCE)
Black(GND)
Black(AGND)
NC
Yellow(R-RET)
KEY
Blue(L-RET)
Red(MIC)
Brown(MIC-PWE)
Yellow(R-OUT)
Blue(L-OUT)
KEY
Black(GND)
Green
White
Red
Black(GND)
Green
White
Red
KEY
Black(GND)
Green
White
Red
Black(GND)
Green
White
Red
Black(KEY)
White(+12V)
Green(TPB+)
Black(VG)
Blue(TPA+)
SATA Cable
USB
USB
IEEE1394
E-SATA
Connector
Black(GND)
White(+12V)
Red(TPB-)
Black(VG)
Orange(TPA-)
1
PSU tray installation
C50.V1010.00E-2
Extension cable for 12V PSU to M/B
Loosing two thumb screws
to release the M/B tray.
Secure the stand off bolts on the M/B
tray which match with the M/B fix points,
place the M/B on the copper bolt, fasten
the screws to secure.
The oval hole on M/B tray
designed for special
server boards, please use
the nut to hold the copper
bolt in place.
3
Release brake
2
3-speed fan
adjustable device
L M H
3 2 1
for SSI CEB/EEB
/
