Panasonic TYWKL09 Operating instructions

Brand: Panasonic

Model: TYWKL09

Type: Operating instructions

Tilting wall hanging bracket for PANASONIC LCD TVs

Fits all 2009 LCD TVs between 26" and 37"

Model No. TY-WKL09

Installation Manual

Thank you for purchasing the wall hanging bracket for your Panasonic LCD TV.

?Please perform installation work correctly after reading this installation manual and the

operation manual for the TV.

?After installation work is complete, please keep this instruction manual for future reference.

?Retain all removed parts and fixings as they may be necessary when returning to the original

configuration.

?This bracket is intended for use with the following TVs;

TX-L26C10, TX-L26X10, TX-L32C10, TX-L32X10, TX-L32X15, TX-L32U10, TX-L32S10, TX-L32G10,

TX-L32V10, TX-L37U10, TX-L37S10, TX-L32G10, TX-L37G15, TX-L37V10

Safety Precautions

To prevent injury to the user and others and to prevent damage to property, directions

that must be followed are explained as shown below.

WARNING

The following displays categorize the degree of danger when mishandled.

Possibility of serious injury and even death when

mishandled.

Be aware of safety factors concerning

the mounting strength.

Insufficient strength may cause

the LCD TV to fall, resulting in

bodily injury.

Installation to be performed by certified

personnel only.

Inadequate installation may

cause the LCD TV to fall, re-

CAUTION

Possibility of injury or damage to surrounding property.

Directions that must be followed are explained using the following symbols.

(Examples of graphical symbols are shown below.)

This symbol indicates that the direction must be followed with caution.

This symbol indicates that the direction is prohibited.

This symbol indicates that the direction must always be followed.

Do not hang from the LCD TV, place

stepsladder, etc.

the LCD TV may become dam-

aged or it may fall, causing

bodily injury.

sulting in bodily injury.

Do not install where tolerance is weak.

If the tolerance of the mounting

location is weak, the LCD TV

may fall resulting in bodily injury.

CAUTION

Do not install with the LCD TV facing

downward, on its side, or upside down.

Heat may build up within the

LCD TV, causing fire as a result.

Ensure there is a space of at least 5 cm

between the LCD TV body and other

objects at the top, bottom and sides,

and at least 4 cm at the back.

Vent holes are located on the

rear of the LCD TV. Blocking

these holes may result in fire.

Do not install in humid or dusty areas,

or where the LCD TV may be exposed to

lampblack, steam or heat.

This may affect the LCD TV, and

may cause fire or electric shock.

At least two persons should perform

installation and removal of the LCD TV

unit.

Dropping the LCD TV may re-

sult in injury.

Always remove the wall hanging bracket

when removing the LCD TV.

Injury may result when acciden-

tally hitting the projected parts.

• Take caution when removing for repairs, etc.

Make sure there is sufficient air circula-

tion so that the ambient temperature

does not exceed 35 °C.

Heat may build up within the

LCD TV, causing fire as a result.

Support Information

M-Form Customer Care Centre

For UK Customers call: 01159 409169

Monday - Thursday 8.00am - 5.00pm Friday 8.00am - 4.00pm

(Excluding public holidays)

e-mail: [email protected]

www.m-formonline.co.uk

mform

1. Assemble the bracket

2. Prepare the LCD TV

Components

A - Bracket Arms (LH + RH)...x1

B - Wall fixing plates...x2

G - Security screw

M5 x 45mm...x2

E - TV protection spacer...x4

D - TV fixing screws

M6 x 25mm...x4

M4 x 25mm...x4

C - Bracket assembly Screw...x8

M5 x 10mm

Allen Key...x2

F - TV insulation spacers...x4

Also required

?Attach wall fixing plates to the left and right arms as

shown (right)

?Use positions 'a' for 400mm width TV fixing points,

use positions 'b' for 200mm width TV fixing points

(shown below)

?Attach the top plate first using all four fixing screws

but do not tighten the screws. Attach the bottom

plate then tighten all the screws on the top and

bottom plate.

?Remove the terminal covers if bracket arms will

obstruct access. Keep covers in a safe place if

removed in case you need to revert back to original

specification.

?Place protection spacers on rear of TV lining up the

holes with the bracket fixing points on the rear of

the TV.

?Fit the isolation spacers in all 4 positions using the

allen key and bolts included in the kit. Use the bolt

size which corresponds to the fixings in your TV.

?Do not use fixings other than those included in the

kit with this bracket.

– 2 –

LH RH

C x8

a ab b

NOTE: Marker arrows

should be facing outwards

– 3 –

3. Attach bracket to wall

4. Hang and secure TV onto bracket

?Partially insert the security screws 'G' into the arms

as shown right (a).

?Hang the TV onto the bracket arms making sure the

insulation spacers engage fully in the corresponding

slots as shown below (b).

?secure the TV by fully inserting the security screws

G' as shown right (c).

?Fit as shown, right, with arms pointing upwards

?If the wall consists of a material such as concrete

and the bolts or nuts must be embedded

beforehand, determine the hole positions by

aligning using the actual bracket or calculate the

hole positions based on the dimensional drawing in

this manual.

?Fasten the screw at position 1, first. Then using

a level, mark out and fasten screws in other

positions marked 'x'.

?Use commercially available screws suitable for the

wall construction for fitting the bracket to the wall.

G x2

Requests regarding handling

Bracket dimensions (mm)

Precautions for wall hanging bracket fitting

?Take care when selecting the location for the TV as it may discolour or deform if located too close to sources of heat, light or direct sunlight.

?Clean with a dry cloth. If unit is very dirty then use a damp cloth with neutral detergent diluted in water. Do not use detergents

containing benzene, thinner or furniture wax as they may cause paint peeling.

?Do not fix stickers or adhesive tape to the product as this may stain the paint.

?The wall hanging bracket is designed for attaching an LCD TV to a vertical wall for viewing. Do not fit to any surface other than a vertical wall.

?The bracket has a lock mechanism for safety reasons. Please ensure that the mounting location allows access to these fixings.

?To ensure optimum performance of your TV do not fit in any of the following situations;

Near sprinklers or fire/smoke detectors

Where there is a risk of exposure to vibration or impact

Near high voltage wires or dynamic power supplies

Locations exposed to air blown from heating or air conditioning equipment

?Fit using fixings and techniques suited to the structure and the materials of the fitting location

?Use commercially available screws suited to the wall construction and surface material for fitting the bracket to the wall.

?Ensure there is no contact between the wall mounting screws or power cord and any metal inside the wall

?Use a convenient power outlet for the TV which can be reached easily.

?Ensure good airflow so the ambient temperature does not exceed 40°C. Failure to do so may cause the LCD TV to malfunction

20080

104

280

100

200

500

440

– 4 –

5. Using the tilt function

?Remove the vertical locking screw from both arms (a).

?Tilt the TV to the desired position and lock the tilt

locking bolt (b) on both arms.

?Always hold the weight of the TV before unlocking the

tilt mechanism.

?Do not completely remove the tilt locking bolt.

?To lock back in vertical position re-insert vertical

locking screws (reverse 'a')

a b

0° to 20°

Panasonic TYWKL09 Operating instructions

Panasonic TYWKL09 Operating instructions

Panasonic TYWKL09 Operating instructions

Related papers

Other documents