Panasonic TYWK32LH1U Operating instructions

Brand: Panasonic

Model: TYWK32LH1U

Type: Operating instructions

– 1 –

Wall hanging bracket (vertical mounting type)

Installation Manual

Model No. TY-WK32LH1U

TQZH487

•

Please perform installation work correctly after carefully reading this installation manual and the

operation manual for the LCD TV.

•

After installation work is complete, please give this installation manual to the customer so they

can read it and keep for future reference.

(It may be needed for maintenance or when moving.)

•

Retain all removed parts. They may become necessary when returning to the original installation

condition.

•

Caution:This bracket intended for use only with Panasonic LCD TV Model TC-32LH1 Series. Use

with other apparatus is capable of resulting in instability causing possible injury.

Thank you very much for purchasing the wall hanging bracket for the Panasonic LCD TV.

Components

Wall hanging bracket . . . x1 Speaker bracket . . . x1

Allen wrench (included tool)

. . . x1

Unit fastening screws (M5-35)

. . . x2

Allen head countersunk

screws (M4-18). . . x4

Dished toothed

washers

. . . x4

Insulation

spacers

. . . x4

Speaker

fastening

screws

. . . x3

Bottom

stickers

. . . x2

– 2 –

Safety Precautions

To prevent injury to the user and others and to prevent damage to property, directions

that must be followed are explained as shown below.

WARNING

The following displays categorize the degree of danger when mishandled.

Possibility of serious injury and even death when

mishandled.

Be aware of safety factors concerning

the mounting strength.

Insufficient strength may cause

the LCD TV to fall, resulting in

bodily injury.

Do not hang from the LCD TV, place

stepsladder, etc.

the LCD TV may become dam-

aged or it may fall, causing

bodily injury.

Prohibited

Installation to be performed by certified

personnel only.

Inadequate installation may

cause the LCD TV to fall, re-

sulting in bodily injury.

Prohibited

Do not install where tolerance is weak.

If the tolerance of the mounting

location is weak, the LCD TV

may fall resulting in bodily injury.

Prohibited

Installation

Be sure to follow

CAUTION

Possibility of injury or damage to surrounding property.

Directions that must be followed are explained using the following symbols.

(Examples of graphical symbols are shown below.)

This symbol indicates that the direction must be followed with caution.

This symbol indicates that the direction is prohibited.

This symbol indicates that the direction must always be followed.

– 3 –

CAUTION

Do not install with the LCD TV facing

downward, on its side, or upside down.

Heat may build up within the

LCD TV, causing fire as a result.

Ensure there is a space of at least 5 cm

between the LCD TV body and other

objects at the top, bottom and sides,

and at least 4 cm at the back.

Vent holes are located on the

rear of the LCD TV. Blocking

these holes may result in fire.

Prohibited

Do not install in humid or dusty areas,

or where the LCD TV may be exposed to

lampblack, steam or heat.

This may affect the LCD TV, and

may cause fire or electric shock.

Prohibited

At least two persons should perform

installation and removal of the LCD TV

unit.

Dropping the LCD TV may re-

sult in injury.

Installation

Always remove the wall hanging bracket

when removing the LCD TV.

Injury may result when acciden-

tally hitting the projected parts.

• Take caution when removing for repairs, etc.

Make sure there is sufficient air circula-

tion so that the ambient temperature

does not exceed 35 °C.

Heat may build up within the

LCD TV, causing fire as a result.

When expanding connection equipment,

be sure to prevent lock release.

This may cause injury.

– 4 –

Fitting procedure ( TY-WK32LH1U )

The weight of the wall hanging bracket is approximately 3.5 kg (8 Ib.). LCD TV unit attached to the wall

hanging bracket weighs approximately 21 kg (46 Ib.).

Check the wall strength at the 6 attachment locations by referring to the dimension drawing of the wall

hanging bracket (given below), and provide adequate reinforcement if strength is not sufficient.

1. Confirm the strength of the proposed fitting location

120

(

/32

)

121

(

/64

)

325

(

/64

)

280

(

/32

)

22.5

(

/64

)

480

(

/64

)

440

(

/64

)

176

(

/16

)

163

(

/64

)

Display

outer profile

Wall attachment holes

(at 6 points)

Wall hanging bracket unit

Speaker bracket

Unit: mm (inches)

Dimensions of clearance required

around wall hanging bracket

* Be sure to fasten with screws.

* Provide spacing for the LCD TV of at least 100 mm (3

/16 inches) to the top and right side, at least 300

mm (11

/16 inches) to the left side, at least 100 mm (3

/16 inches) to the bottom and at least 42 mm

/32 inches) to the rear.

Notes

• There are 12 holes in the wall hanging bracket. If the wall material is wood, and adequate attachment strength

cannot be ensured by fastening at the 6 points at right, use as many spare holes as necessary. However,

exercise care because some wall materials may crack if screws are located too close together.

The above dimensions are important. Do not fit at any location where these dimensions cannot be secured.

2. Fit wall hanging bracket to wall

• Fit so that the arrow marks on the wall hanging bracket point upward.

• If the wall consists of a material such as concrete and bolts or nuts must be embedded beforehand, determine

the hole positions by aligning using the actual wall hanging bracket, or calculate hole positions based on the

dimension drawing, and then embed "M6" bolts or nuts.

When embedding bolts, locate so that the bolts protrude from the wall by

10 mm (

/64 inches) to 15 mm (

/32 inches).

(1) Fasten the screw at the top center hole first.

(2) Using a level, correct any bracket inclination, and then fasten screws at

the remaining 5 locations.

• Use commercially available M6 screws suited to the wall surface material

(wood, steel frame, concrete etc.) for fitting the bracket to the wall.

Note

For 32-inch

908

(35

)

527

(20

)

131

)

ABC

– 5 –

Fit the insulation spacers to the LCD TV.

Place the LCD TV unit face down on a blanket or other soft cloth that is clean and free of debris, and follow the

procedure below.

(1) Remove the terminal section cover

on the left side of the LCD TV, and

the tuner section cover at the bot-

tom center.

* Keep the removed covers in a safe

place. (They will be needed again

if you decide to change to a spe-

cial-purpose or floor-type stand.)

(2) Affix the enclosed bottom stickers (1

each for left and right) to the stand

pole holes at the bottom center of

the LCD TV. (Affix the bottom stick-

ers by peeling off the separator,

aligning the perforations and folding

at a right angle, as shown in the dia-

gram.)

(3) Fit the enclosed Allen head countersunk screws, dished tooth washers and insulation spacers (4 each) as

shown in the diagram at right and tighten using the included Allen wrench.

3. Prepare the LCD TV

(1) Hook the insulation spacers on the

top of the LCD TV into the notches

at the top of the wall hanging

bracket.

(2) Insert the bottom insulation spac-

ers while lowering the LCD TV, and

then gently allow it to drop down.

(3) Attach securely using the included

unit fastening screws (1 each for

left and right).

• Always fit the unit fastening screws to ensure that the LCD TV unit cannot be accidentally dislodged from the

wall hanging bracket.

Bottom

stickers

Stand

pole hole

Tuner

section cover

Terminal

section cover

Allen head countersunk screw

Dished toothed washer

Insulation spacer

Allen wrench

Inclined surface

Upper notch

Lower hole

Insulation

spacer

(1)

(3)

(2)

Screw securing

hole for LCD

TV unit fastening

Screw for LCD

TV unit fastening

Wall hanging

bracket

Red screw for

open / close

fastening

Wall

Insulation spacer

LCD TV

4. Fit and fasten the LCD TV unit to the wall hanging

bracket

Note

– 6 –

* The SB-PC50 center speaker for home theater (sold separately) can be

fitted to the wall hanging bracket.

5. Center speaker fitting and wiring

6. Fasten wall hanging bracket

(1) After wiring, remove the red screw for open/close fasten-

ing (on the left side), lift the TV unit towards yourself once,

and then slowly lower it. The lock will release.

(2) Securely tighten the red screws for open/close fastening

(1 each on the left and right) on the sides of the wall

hanging bracket.

• Always fit the red screws for open/close fastening to ensure that the LCD TV unit cannot be accidentally dis-

lodged.

(1) Remove the red screws for open/close fastening (one

each on the left and right) .

(2) Tentatively fasten by lifting up the LCD TV towards

yourself, as shown in the diagram at left, pressing

the lock bracket upward in the arrow direction (up),

and checking that the bracket is locked. Securely

fasten the red screw for open/close fastening (one

screw on the left) in the lock bracket fastening

hole .

(3) Securely fasten the SB-PC50 to the speaker bracket

using the included speaker fastening screws (x2).

(4) Insert the speaker bracket into the speaker bracket

attachment holes on the wall hanging bracket, and

securely fasten with the included speaker bracket

fastening screw (x1).

(5) Tidily route the wiring for the LCD TV, video unit, and

any other wiring using the wiring hole in the speaker

bracket.

LCD TV

Wall hanging

bracket

Lock bracket

fastening hole

Wall

Red screw for

open / close

fastening

Red screw for

open / close

fastening

LCD TV

Wall hanging

bracket

Speaker bracket

attachment holes

Speaker

fastening screws

Wiring holes

Speaker (SB-PC50)

Speaker bracket

fastening screw

Speaker

bracket

Speaker

fastening hole

Wall

Wall handing

bracket

Fitting hole for

red screw for

open / close fastening

Red screw for

open / close

fastening

Note

– 7 –

(1) Remove the screws for unit fastening (1 each on the

left and right) that are fitted to the wall hanging bracket

sides.

(2) While lifting the bottom of the LCD TV unit, pull it

towards yourself.

(3) When the lower insulation spacers are freed, keep

lifting upward.

7. Removal of LCD TV unit

Insulation spacer

Wall

(3)

(2)

Wall hanging

bracket

(1)

Screw for

LCD TV

unit fastening

Requests regarding handling

♦ The wall hanging bracket is for use in attaching a LCD TV unit to a vertical wall for viewing. Do not fit to any

surface other than a vertical wall.

♦ The equipment has a lock mechanism on the left side, so provide at least 300 mm (11

inches ) of space from

the wall surface.

♦ To ensure correct LCD TV performance and prevent trouble, do not fit at any of the following locations.

• Near sprinklers or fire/smoke detectors

• Where there is a risk of exposure to vibration or impact

• Near high-voltage wires or dynamic power supplies

• Locations exposed to air blown from heating equipment

♦ Fit using techniques suited to the structure and materials of the fitting location.

♦ Use commercially available M6 screws suited to the wall surface material (wood, steel frame, concrete etc.) for

fitting the bracket to the wall.

♦ Fit so there is no contact between the attachment screws or power cord and any metal inside the wall.

♦ For the TV power supply plug, use a power supply outlet that can be reached easily.

♦ Ensure good air flow so that the equipment ambient temperature does not exceed 40°C. Failure to do this may

cause heat to build up inside the LCD TV, resulting in malfunction.

1) Exercise care when selecting the location for the TV because it may discolor or deform due to light or heat if it is

placed where it is exposed to direct sunlight, or near a heater.

2) Upkeep

Wipe with a dry cloth. If the unit is extremely soiled, first wipe off soiling with a neutral detergent diluted in water,

and then wipe with a dry cloth. Do not use cleaners such as benzene, thinner or furniture wax because they may

cause paint peeling. (If using a chemical wiping cloth, follow any precautions included.)

3) Do not affix adhesive tape or stickers to the product. Either may stain the wall hanging bracket or surface of the

wiring cover for close-to-the-wall installation.

Precautions for wall hanging bracket fitting

Matsushita Electric Industrial Co., Ltd.

Web Site : http://www.panasonic.co.jp/global/

For assistance, please call: 1-800-211-PANA (7262)

or send e-mail to : [email protected]

or visit us at www.panasonic.com

For assistance, please call: 787-750-4300

or visit us at www.panasonic.com

For assistance, please call: 1-800-561-5505

or visit us at www.panasonic.ca

(U.S.A)

(Puerto Rico)

(Canada)

Printed in Japan

Panasonic TYWK32LH1U Operating instructions

Panasonic TYWK32LH1U Operating instructions

Panasonic TYWK32LH1U Operating instructions

Related papers

Other documents