Panasonic TYWK22LR1W Operating instructions

Brand: Panasonic

Model: TYWK22LR1W

Type: Operating instructions

Panasonic TYWK22LR1W wall-hanging bracket is compatible with numerous Panasonic LCD TVs, ensuring a secure and versatile mounting solution. It allows for flexible viewing angles, with adjustable tilt from 5 degrees upsweep to 10 degrees downsweep. Installation is straightforward, with all necessary components included. Safety precautions are outlined in the manual to ensure a successful and hazard-free setup.

Installation Manual

Wall-hanging bracket

for Combination LCD TV / DVD Player

and LCD TV

Model No. TY-WK22LR1W

Please perform installation work correctly after carefully reading this

installation manual and the operation manual for the Combination LCD

TV / DVD Player and LCD TV.

After installation work is complete, please give this installation manual to

the customer so they can read it and keep for future reference.

(It may be needed for maintenance or when moving.)

Retain all removed parts. They may become necessary when returning

to the original installation condition.

Caution:This bracket intended for use only with Panasonic LCD TV Model

TC-22LH30 / TX-22LX2 / TC-20LA2 / TX-20LA2 / TC-20LB30 / TX-20LB30

/ TC-17LA2 / TX-17LX2 / TC-14LA2 series and TC-20LA2D / TC-17LA2D

/ TC-14LA2D.

Use with other apparatus is capable of resulting in instability causing

possible injury.

Thank you very much for purchasing the wall-hanging bracket for the

Panasonic Combination LCD TV / DVD Player and LCD TV.

TQZH566

MBS0504A0 (MBS)

Matsushita Electric Industrial Co., Ltd.

Web Site : http://www.panasonic.co.jp/global/

Wall-hanging bracket dimesional drawings

Safety Precautions

To prevent injury to the user and others and to prevent damage to property, directions

that must be followed are explained as shown below.

Be aware of safety factors con-

cerning the mounting strength.

Inadequate installation may

cause the Combination LCD

TV / DVD Player and LCD TV

to fall, resulting in bodily injury.

Do not install where tolerance is weak.

If the tolerance of the mount-

ing location is weak, the

Combination LCD TV / DVD

Player and LCD TV may fall

resulting in bodily injury.

Insufficient strength may

cause the Combination LCD

TV / DVD Player and LCD TV

to fall, resulting in bodily injury.

Do not hang from the Combina-

tion LCD TV / DVD Player and

LCD TV, use a stepladder.

the Combination LCD TV/

DVD Player and LCD TV may

become damaged or it may

fall, causing bodily injury.

Possibility of serious injury and even death

when mishandled.

Directions that must be followed are explained using the following symbols.

(Examples of graphical symbols are shown below.)

This symbol indicates that the direction must be followed with caution.

This symbol indicates that the direction is prohibited.

This symbol indicates that the direction must always be followed.

Possibility of injury or damage to surrounding

property.

WARNING

Prohibited

Installation to be performed by

certified personnel only.

WARNING

The following displays categorize the degree of danger when mishandled.

CAUTION

Installation

Be sure to follow

2 19

Wall-hanging bracket A (Main unit side)

[ Unit: mm ]

t=1.6

t=2.0

Wall-hanging bracket B (Wall side)

Overall assembly

100

116

58.4

41.8

14.8

100

7100

114

116

100

8.5

48.5

106.3

78.5

112.3

114

10°

5°

124

99.5

CAUTION

Do not install in humid or dusty

areas, or where the Combination

LCD TV / DVD Player and LCD TV

may be exposed to lampblack,

steam or heat.

This may affect the Combi-

nation LCD TV / DVD Player

and LCD TV, and may cause

fire or electric shock.

Do not install with the Combina-

tion LCD TV / DVD Player and

LCD TV facing downward, on its

side, or upside down.

Heat may build up within

the Combination LCD TV

/ DVD Player and LCD TV,

causing fire as a result.

Vent holes are located on

the rear of the Combination

LCD TV / DVD Player and

LCD TV. Blocking these

holes may result in fire.

At least two persons should per-

form installation and removal of

the Combination LCD TV / DVD

Player and LCD TV unit.

Dropping the Combination

LCD TV / DVD Player and

LCD TV may result in injury.

Ensure there is a space of at least

5 cm between the Combination

LCD TV / DVD Player and LCD TV

body and other objects at the top

and bottom, at least 10 cm at the

sides and 4 cm at the back.

Make sure there is sufficient air

circulation so that the ambient tem-

perature does not exceed 35

Heat may build up within

the Combination LCDTV/

DVD Player and LCD TV,

causing fire as a result.

Always remove the wall-hanging

bracket when removing the Com-

bination LCD TV / DVD Player and

LCD TV.

Injury may result when

accidentally hitting the

projected parts.

Prohibited

•Take caution when removing for

repairs, etc.

Prohibited

Installation

LCD television removal

Fixing screw

Remove the angle fastening 2

screws mounted to the left and right

sides of the wall-hanging bracket.

While lifting the Combination LCD TV

/ DVD Player and LCD TV, pull it

away from the wall and remove.

318

3 Install at the desired angle.

Position the LCD TV wall-hanging bracket at the desired angle from 5°

upsweep to 10° downsweep.

Set the angle by adjusting the notches of wall-hanging bracket B (wall

side) and the concave section of wall-hanging bracket A (main unit side) to

the desired angle.

2 Wall-hanging bracket fastening.

To prevent the main unit from falling, fix the main unit using fixing screws

(2 units) from both sides. If the fixing holes of the brackets do not align,

installation is incorrect. Check the installation again and fix so that screw

holes are aligned.

Do not apply force to the bracket in an attempt to make it exceed

the setting angle of 5° upsweep to 10° downsweep. Damage to or

malfunction of the LCD TV may result.

Caution

Fixing screw

Be sure to mount the angle fastening screws on the left and right to

prevent the Combination LCD TV / DVD Player and LCD TV from falling.

Caution

The wall-hanging bracket is for installing an Combination LCD TV / DVD

Player and LCD TV on a vertical wall for viewing. Do not use it for installing in

any other place than on a vertical wall.

The stand must be removed from the Combination LCD TV / DVD Player and

LCD TV before the wall-hanging bracket may be mounted. Before starting work,

be sure to turn the power off and unplug the AC adapter power supply plug.

Install using techniques that suit the structure and materials of the installation

location.

Use commercially available M4 bolts suitable for the wall material (wood,

steel frame, concrete etc.) as the screws for fastening to the wall.

Allow sufficient strength for safety.

The weight of the Combination LCD TV / DVD Player and LCD TV is

approximately 4-10 kg.

When mounting on a wall, perform work so that it can withstand the weight of

the television and so that the bracket will not come loose from vibration, etc.

Reinforce the bracket if the mounting section strength is insufficient.

The television may fall if the installation is insufficient or if the screws are loose.

Check to make sure there are no electrical wires within the wall.

Use the supplied cable clampers to fix cables. Never fix cables using staples.

Components

Before starting installation, first check that all components have been supplied.

Precautions for installation work

( 1 )

(M4 × 12 mm)

Wall-hanging bracket A

(main unit side)

Angle fixing screw

(for main unit side / wall side fixing)

Bracket mounting screw

(main unit side)

( 4 )

( 2 )

Wall-hanging bracket B

(wall side)

( 1 )

174

To guarantee Combination LCD TV / DVD Player and LCD TV performance

and prevent problems, do not install in locations such as the following:

About the installation location

Be sure to explain the following points to the customer:

The Combination LCD TV / DVD Player and LCD TV is best viewed directly

from the front.

Avoid areas where the florescent lighting reflects on the Combination LCD

TV / DVD Player and LCD TV surface. Although vertical angles can be

adjusted, the hanging bracket does not move horizontally.

For the main power supply plug, use an outlet that can be easily reached

by hand. Also make sure that the television is at a height where the power

supply switch can be easily operated, and that it is at a distance within the

remote control range (approximately 6 m from the front).

For the installation height, do not exceed the range of the connection cords

(AC adapter, antenna, etc.).

Be sure to install in a location where the AC adapter is not suspended and

where it can be placed on the floor, table, etc.

Install where there are no objects within 20 cm below the Combination

LCD TV / DVD Player and LCD TV.

Check the installation height, depth, wall structure, etc., before performing

installation work.

Near sprinklers or heat / smoke detectors

Where there is a risk of vibration or impact

Near high voltage wires or motors

Near sources of magnetism, heat, water vapor or soot

Exposed to air from heating equipment

Ensure air can flow around the Combination LCD TV / DVD Player and LCD

TV so that the temperature does not exceed 35 °C.

Otherwise malfunction may occur due to the build-up of heat inside the

Combination LCD TV / DVD Player and LCD TV.

1 Installing on the wall.

Attaching the Combination LCD TV / DVD Player and

LCD TV to the wall-hanging bracket B (wall side)

To prevent damage to the wall, make sure that the main unit is

securely mounted on the notches of wall-hanging bracket B (wall

side) before letting go of the main unit. Installation of the televi-

sion on the wall should be performed by at least two people.

Caution

Fixing screws

Fixing hole

Wall-hanging

bracket A

Wall-hanging

bracket B

(Wall side)

Fixing

Screw

Holding part

Installation procedure

(Cont'd)

Put the fixing screws on the fixing holes located on wall-hanging brackets

B (wall side).

Hang the Combination LCD TV / DVD Player and LCD TV on wall-

hanging bracket B.

516

Before starting the mounting procedure, remove the AC adapter and connection

cable attached to the LCD TV. Be sure to perform mounting correctly and securely.

1 Remove the photo stand.

Align the holes in wall-hanging bracket A with the screw holes in the LCD TV.

2 Mount wall-hanging bracket A.

Note:

Store the photo stand and screws care-

fully in case they are required in future.

For the TC-14LA2D

When connecting cables to the LCD TV, certain cables may touch the wall.

Avoid putting any weight on the cables when they touch the wall.

Securely fasten with the 4 bracket

mounting screws A (M4 × 12 mm).

Remove the 3 screws.

Slowly pull off the photo stand in the

upward direction.

Check the strength of the intended installation position

The weight of the Combination LCD TV / DVD Player and LCD TV installed on

the wall-hanging bracket is approximately 4-10 kg.

Referring to the dimension drawing below, check the wall strength at the 4

mounting positions. If strength is insufficient, provide reinforcement.

Mounting wall-hanging bracket B

If bolts or nuts must be embedded in the wall beforehand, such as with a

concrete wall, determine the hole positions by aligning with the actual wall-

hanging bracket B, or by referring to the dimension drawing, and embed

anchors of approximately 4 mm diameter.

Note:

Use commercially available M4 screws suitable for the mounting surface

material as the screws for fastening to the wall.

Wall-hanging bracket B

Installation procedure

Wall mounting holes ( × 4)

[ Unit: mm ]

Using a level, determine the installation

position where the mounting is horizontal, and

mark the wall.

Fix wall-hanging bracket B (wall side) using

commercially available M4 4 screws.

8.5

48.5

106.3

78.5

112.3

156

Before starting the mounting procedure, remove the connection cable attached to

the LCD TV. Be sure to perform mounting correctly and securely.

1 Remove the stand cover.

3 Mount wall-hanging bracket A.

2 Remove the TV stand.

Align the holes in wall-hanging bracket A with the screw holes in the LCD TV.

Note:

Store the stand, stand cover and screws

carefully in case they are required in future.

When connecting cables to the LCD TV, certain cables may touch the wall.

Avoid putting any weight on the cables when they touch the wall.

Installation procedure

(Cont'd)

Remove the screw.

Slowly pull off the stand cover in the

upward direction.

Securely fasten with the 4 bracket

mounting screws A (M4 × 12 mm).

Remove the 4 screws.

Remove the TV stand.

For the TC-22LH30 / TC-22LH30C

TX-22LX2 / TX-22LX2F / TX-22LX2P

Preparation of television

Installation procedure

(Cont'd)

Align the holes in wall-hanging bracket A with the screw holes in the LCD TV.

3 Mount wall-hanging bracket A.

Note:

Store the stand, stand cover and screws

carefully in case they are required in future.

2 Remove the TV stand.

For the TC-14LA2 / TC-14LA2C

When connecting cables to the LCD TV, certain cables may touch the wall.

Avoid putting any weight on the cables when they touch the wall.

Before starting the mounting procedure, remove the AC adapter and connection

cable attached to the LCD TV. Be sure to perform mounting correctly and securely.

1 Remove the stand cover.

Remove the screw.

Slowly pull off the stand cover in the

upward direction.

Securely fasten with the 4 bracket

mounting screws A (M4 × 12 mm).

Remove the 4 screws.

Pull the TV stand slightly towards

yourself, and remove it in the upward

direction.

714

Before starting the mounting procedure, remove the AC adapter and connection

cable attached to the LCD TV. Be sure to perform mounting correctly and securely.

Align the holes in wall-hanging bracket A with the screw holes in the LCD TV.

3 Mount wall-hanging bracket A.

1 Remove the photo stand.

2 Remove the photo stand mounting bracket.

When connecting cables to the LCD TV, certain cables may touch the wall.

Avoid putting any weight on the cables when they touch the wall.

Antenna

Terminal

Back of the TV

The antenna cable may be bent and

damaged near the connector if the

F-Adapter is used for connection.

In such situations, remove the F-

Adapter and connect the antenna cable

directly.

Note:

Store the photo stand, photo stand mount-

ing bracket and screws carefully in case

they are required in future.

DC IN 15V

PS TBMU428

AUDIO

VIDEO S-VIDEO

AUDIO

COMPONENT VIDEO INPUT

INPUT

VIDEO

F-Adapter

Securely fasten with the 4 bracket

mounting screws A (M4 × 12 mm).

Remove the 4 screws.

Remove the photo stand.

Remove the 2 screws.

Remove the photo stand mounting bracket.

For the TC-17LA2D

Installation procedure

(Cont'd)

Before starting the mounting procedure, remove the connection cable attached to

the LCD TV. Be sure to perform mounting correctly and securely.

1 Remove the TV stand.

Align the holes in wall-hanging bracket A with the screw holes in the LCD TV.

2 Mount wall-hanging bracket A.

When connecting cables to the LCD TV, certain cables may touch the wall.

Avoid putting any weight on the cables when they touch the wall.

Remove the 4 screws.

Remove the TV stand.

Securely fasten with the 4 bracket

mounting screws A (M4 × 12 mm).

Note:

Store the stand and screws carefully in

case they are required in future.

For the TC-20LA2 / TC-20LA2C / TC-20LA2H / TC-20LA2G

TX-20LA2 / TX-20LA2F / TX-20LA2P / TX-20LA2M

TX-20LA2A / TX-20LA2T / TX-20LA2X

138

Before starting the mounting procedure, remove the connection cable attached to

the LCD TV. Be sure to perform mounting correctly and securely.

Align the holes in wall-hanging bracket A with the screw holes in the LCD TV.

3 Mount wall-hanging bracket A.

Note:

Store the photo stand, photo stand mount-

ing bracket and screws carefully in case

they are required in future.

1 Remove the photo stand.

2 Remove the photo stand mounting bracket.

When connecting cables to the LCD TV, certain cables may touch the wall.

Avoid putting any weight on the cables when they touch the wall.

Securely fasten with the 4 bracket

mounting screws A (M4 × 12 mm).

Remove the 4 screws.

Remove the photo stand.

Remove the 2 screws.

Remove the photo stand mounting bracket.

For the TC-20LA2D

Installation procedure

(Cont'd)

Before starting the mounting procedure, remove the AC adapter and connection

cable attached to the LCD TV. Be sure to perform mounting correctly and securely.

1 Remove the stand cover.

3 Mount wall-hanging bracket A.

2 Remove the TV stand.

For the TX-17LX2 / TX-17LX2F / TX-17LX2P

Align the holes in wall-hanging bracket A with the screw holes in the LCD TV.

When connecting cables to the LCD TV, certain cables may touch the wall.

Avoid putting any weight on the cables when they touch the wall.

Remove the 2 screws.

Slowly pull off the stand cover in the

upward direction.

Securely fasten with the 4 bracket

mounting screws A (M4 × 12 mm).

Remove the 4 screws.

Remove the TV stand.

Note:

Store the stand, stand cover and screws

carefully in case they are required in future.

912

For the TC-17LA2 / TC-17LA2C

Before starting the mounting procedure, remove the AC adapter and connection

cable attached to the LCD TV. Be sure to perform mounting correctly and securely.

1 Remove the TV stand.

Align the holes in wall-hanging bracket A with the screw holes in the LCD TV.

2 Mount wall-hanging bracket A.

The antenna cable may be bent and

damaged near the connector if the

F-Adapter is used for connection.

In such situations, remove the F-

Adapter and connect the antenna cable

directly.

When connecting cables to the LCD TV, certain cables may touch the wall.

Avoid putting any weight on the cables when they touch the wall.

Remove the 4 screws.

Remove the TV stand.

Securely fasten with the 4 bracket

mounting screws A (M4 × 12 mm).

DC IN 15V

PS TBMU428

AUDIO

VIDEO S-VIDEO

AUDIO

COMPONENT VIDEO INPUT

INPUT

VIDEO

F-Adapter

Antenna

Terminal

Back of the TV

Note:

Store the stand and screws carefully in

case they are required in future.

Installation procedure

(Cont'd)

Before starting the mounting procedure, remove the connection cable attached to

the LCD TV. Be sure to perform mounting correctly and securely.

1 Remove the stand cover.

Align the holes in wall-hanging bracket A with the screw holes in the LCD TV.

3 Mount wall-hanging bracket A.

Note:

Store the stand, stand cover and screws

carefully in case they are required in future.

2 Remove the TV stand.

For the TC-20LB30 / TC-20LB30C / TC-20LB30H / TC-20LB30G

TX-20LB30F / TX-20LB30P / TX-20LB30M / TX-20LB30A

TX-20LB30T / TX-20LB30X

When connecting cables to the LCD TV, certain cables may touch the wall.

Avoid putting any weight on the cables when they touch the wall.

Remove the AC cord from the

clamper attached to the stand cover.

Remove the 2 screws.

Slowly pull off the stand cover in the

upward direction.

Securely fasten with the 4 bracket

mounting screws A (M4 × 12 mm).

Remove the 2 screws.

Remove the TV stand.

1110

Panasonic TYWK22LR1W Operating instructions

Panasonic TYWK22LR1W Operating instructions

Panasonic TYWK22LR1W Operating instructions

Related papers

Other documents