Anova D1630C Assembly Instruction

Type
Assembly Instruction

This manual is also suitable for

1
ASSEMBLY INSTRUCTIONS
D1630C - Round Perforated 3-Seat ADA Pedestal Table
anovafurnishings.com
888.535.5005 tel
TOOLS NEEDED:
Ratchet with a 9/16” socket
Ratchet with a 3/4" socket
9/16” Open end or box end wrench
3/4" Open end or box end wrench
TABLE COMPONENTS:
ASSEMBLY HARDWARE: All hardware is stainless steel.
ASSEMBLY:
(1) Table Top
(3) Seat Supports
1.
Inspect the shipping container contents for damage and to
determine that all components and hardware are present.
2. Lay all parts on a soft work surface or on the shipping
packaging to prevent damage to finish.
NOTE: Before assembling the nuts to the bolts, it is
recommended that a light oil or petroleum jelly be applied to the
screw threads.
(3) Flat Seats
(1) Center Post
(1)
Table Top Support
(16) 3/8”-16 x 1 1/4"
Hex Head Bolts
(11) 1/2
Nylock Nuts
D1630C
(16) 3/8
Nylock Nuts
(16) 3/8” Flat Washers
(11) 1/2"-13 x 5 1/2"
Hex Head Bolts
(11) 1/2" Flat Washers
2
3. Locate the center post and anchor in place according to
the anchor instructions.
4. Locate a seat support and a seat. Install a 3/8” flat washer
on four 3/8”-16 x 1 1/4" hex head cap bolts through the
mounting hole on the seat and seat support. Place a 3/8”
flat washer and a 3/8” Nylock nut on the ends of the bolts
and leave finger tight.
Once all nuts are installed tighten using a ratchet with a
9/16socket and a 9/16” open end or box end wrench.
Repeat this step for the remaining seats and seat supports.
3/8” Nylock Nut
5.
Locate the seat support mounting moles on the center
post and align two of the seat assemblies with the
holes on opposite sides of the center post.
3/8” Flat Washer
3/8” Flat Washer
3/8”-16 x 1 1/4"
Hex Head Cap
S
6.
Install a 1/2" flat washer on four
1/2"-13 x 5 1/2" hex head cap
bolts and insert through the
mounting holes on the seat
assembly, center post, and the
other seat assembly. Place a
1/2" flat washer and 1/2” Nylock
nut on the ends of the bolts and
leave finger tight.
Once all nuts have been
installed, tighten using a ratchet
with a 3/4” socket and a 3/4"
open end or box end wrench.
Repeat this step for the
remaining seat assembly.
3
7. Locate the table top support and the table top
support mounting holes on the center post.
Install a 1/2" flat washer on a 1/2"-13 x 5 1/2" hex
head cap bolt and insert through the table top
support and the center post. Place a 1/2" flat
washer and a 1/2" Nylock nut on the ends of the
bolts and leave finger tight.
Once all nuts have been installed, tighten with a
ratchet with a 3/4” socket and a 3/4" open end
or box end wrench.
8. Locate the table top and position over the table top
support. Install a 3/8” flat washer on four 3/8”-16 x 1
1/4" hex head bolts and insert the bolts through the
table top mounting holes and the table top support.
Place a 3/8” flat washer and 3/8” Nylock nut on the
ends of the bolts and leave finger tight.
Once all nuts have been installed, tighten with a
ratchet with a 9/16” socket and a 9/16” open end or
box end wrench.
9. After two weeks, retighten all hardware.
10. Recommend a ½x 6” wedge style anchor
bolt. The slab should be a minimum of 8
thick.
4
04/20/2016 Copyright 2016 ANOVA® Made in U.S.A
Assembly and Replacement Parts
Table Top
Table Top Support
Seat Support
Seat
Center Post
NOTE: Please contact Customer Care at 1-866-797-1761 to receive assistance in placing a replacement part order.
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4

Anova D1630C Assembly Instruction

Type
Assembly Instruction
This manual is also suitable for

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI