2. Carlisle
  3. Ransburg- RPAA-02A

Carlisle Ransburg- RPAA-02A User manual

  • Hello! I've reviewed the service instruction document for Ransburg RPAA-02A and RPA-1 spray guns. This document provides detailed steps for inserting a conductive plug to the high voltage cascade connection, including the specific tools needed and the order of operations. I can answer questions related to this instruction and clarify any points in this procedure.
  • What is the purpose of the conductive plug?
    Which models does this instruction relate to?
    What tool is required for plug insertion?
SERSER
SERSER
SERVICE INSTRUCTIONVICE INSTRUCTION
VICE INSTRUCTIONVICE INSTRUCTION
VICE INSTRUCTION
RPAA-02ARPAA-02A
RPAA-02ARPAA-02A
RPAA-02A AND/OR RP AND/OR RP
AND/OR RP AND/OR RP
AND/OR RPA-1A-1
A-1A-1
A-1
SERVICE INSTRUCTION
SI-0530-06SI-0530-06
SI-0530-06SI-0530-06
SI-0530-06
RPRP
RPRP
RPAAAA
AAAA
AA and RP and RP
and RP and RP
and RPAA
AA
A Cascade High Cascade High
Cascade High Cascade High
Cascade High
VV
VV
Voltage Connectionoltage Connection
oltage Connectionoltage Connection
oltage Connection
The gun body has a small cavity at the base of the
cascade for the high voltage contact spring. There
is a gap between the cascade and body that can
be bridged by stretching the spring on the cascade,
but is not advised. The specified method is to
insert the conductive plug at the base of the
cascade. An insertion tool is used to position then
drive the plug into the body in the middle of the
cascade labyrinth. This plug needs to be added to
all the RPAA's and the first ten (10) RPA gun
bodies (Serial Numbers 0525101 thru 0525110).
High VHigh V
High VHigh V
High Voltage Plug Insertionoltage Plug Insertion
oltage Plug Insertionoltage Plug Insertion
oltage Plug Insertion
Use the tool to position and then drive in the plug.
Follow these steps:
1. Locate tool and plug.
2. Locate plug into tool end as shown.
3. Use the tool to start the plug into the body.
Flat EndFlat End
Flat EndFlat End
Flat End
A11736A11736
A11736A11736
A11736
ToolTool
ToolTool
Tool
A11735A11735
A11735A11735
A11735
PlugPlug
PlugPlug
Plug
ManufacturingManufacturing
ManufacturingManufacturing
Manufacturing
1910 North Wayne Street
Angola, Indiana 46703-9100
Telephone: 260/665-8800
Fax: 260/665-8516
TT
TT
Technical/Service Assistanceechnical/Service Assistance
echnical/Service Assistanceechnical/Service Assistance
echnical/Service Assistance
Automotive Assembly and Tier I Telephone: 800/ 626-3565 Fax: 419/ 470-2040
Industrial Systems Telephone: 800/ 233-3366 Fax: 419/ 470-2071
Ransburg Guns Telephone: 800/ 233-3366 Fax: 419/ 470-2071
TT
TT
Technical Support Representative will direct you to the appropriate telephone number for orderingechnical Support Representative will direct you to the appropriate telephone number for ordering
echnical Support Representative will direct you to the appropriate telephone number for orderingechnical Support Representative will direct you to the appropriate telephone number for ordering
echnical Support Representative will direct you to the appropriate telephone number for ordering
Spare Parts.Spare Parts.
Spare Parts.Spare Parts.
Spare Parts.
Form No. SI-0530-06
Litho in U.S.A.
06/06
© 2006 Illinois Tool Works Inc. All rights reserved.
Models and specifications subject to change without notice.
5. Drive tool with a rubber mallet to firmly set the
plug.
6. Check continuity between these two points
(conductive plug and contact button) as shown.
4. Pull tool out and flip tool over to finish insertion
using opposite end.
CavityCavity
CavityCavity
Cavity
/