INSTALLATIONSANLEITUNGEN
Der Mindestabstand zwischen dem Kochfeld und der unteren Kante der
Dunstabzugshaube muss bei Elektroplatten 50 cm und bei Gasherden oder
kombinierten Herden 65 cm betragen. Schreiben die Installationsanweisungen des
Gaskochfelds einen größeren Abstand vor, ist dieser natürlich zu beachten.
ACHTUNG! Das Abluftrohr und die Befestigungsschellen (15) werden nicht
mitgeliefert und sind gesondert zu beziehen.
INSTALLATION SHEET
The minimum distance between the support surface of the recipients on the cooking
device and the lowest part of the hood must not be less than 50 cm in case of electric
cookers and 65 cm for gas or combined cookers. If the installation instructions for the
gas cooker specify a greater distance, this must be taken into account. Important!
The exhaust pipe and fixing clamps (15) are not supplied and must be purchased
separately.
FICHE D’INSTALLATION
La distance minimum entre la surface de support des récipients sur le dispositif de
cuisson et la partie la plus basse de la hotte ne doit pas être inférieure à 50 cm pour
les cuisinières électriques et à 65 cm pour les cuisinières à gaz ou mixtes. Si les
instructions d’installation du dispositif de cuisson à gaz indiquent une distance
supérieure, il est nécessaire de la respecter. Attention ! Le conduit d’évacuation et les
colliers de fixation (15) ne sont pas fournis et doivent être achetés à part.
INSTALLATIEKAART
De minimale afstand tussen het steunoppervlak van de pannen op het kooktoestel en
het laagste deel van de afzuigkap mag niet minder dan 50 cm zijn bij elektrische
kooktoestellen en 65 cm bij kooktoestellen op gas of gemengd. Als de installatie-
instructies van het kooktoestel op gas een grotere afstand aangeven, moet hiermee
rekening gehouden worden. Let op! Afvoerpijp en klembanden (15) worden niet
bijgeleverd en moeten apart worden aangeschaft.
D
GB
F
NL
FICHA DE INSTALACIÓN
La distancia mínima entre la superficie de apoyo de los recipientes en la placa de
cocción y la parte más baja de la campana no debe ser inferior a 50 cm en caso de
cocinas eléctricas y 65 cm para cocinas a gas o mixtas. Si en las instrucciones de
instalación de la placa de cocina a gas se especifica una distancia mayor respecto a la
indicada, es necesario tenerlo en cuenta. ¡Atención! El tubo de evacuación y las bridas
de fijación (15) no están incluidos y se deben comprar por separado.
FICHA DE INSTALAÇÃO
A distância mínima entre a superfície de suporte dos recipientes no dispositivo de
cozedura e a parte mais baixa do exaustor do fogão deve ser não inferior a 50 cm no
caso de fogões eléctricos e de 65 cm no caso de fogões a gás ou mistos. Respeite as
instruções de instalação do dispositivo de cozedura a gás se estas especificarem uma
distância superior à indicada. Atenção! O tubo de descarga e as braçadeiras de fixação
(15) não são fornecidos, devendo ser comprados à parte.
SCHEDA INSTALLAZIONE
La distanza minima fra la superficie di supporto dei recipienti sul dispositivo di cottura
e la parte più bassa della cappa da cucina deve essere non inferiore a 50 cm in caso di
cucine elettriche e di 65 cm in caso di cucine a gas o miste. Se le istruzioni di
installazione del dispositivo di cottura a gas specificano una distanza maggiore rispetto
a quella specificata, bisogna tenerne conto. Attenzione! Il tubo di scarico e le fascette
di fissaggio (15) non sono fornite e vanno acquistate a parte.
ùüùü+ùùùþ
þ0$12.)12.1.01.12030.12!"2&10#+121#10#
.0!.2 ".12 $.)20! 10 2 #. !! 32!. /0!0.0.
!)20!.)FP100!2&102!+012+..)FP10 #0"
.0! #2"ü /0"0.212.1"2"012.".0! #1#12 *
0.*20!.)12.1101$1000 #$0 !12003.!)1202"1$02"
/0"! 1 $ 1&."..&".2. !.120!&1"/0
/.202.02 . !! 32!..!0 .. 2 *$&!12
E
P
I
GR
3
4
4
4
4
4
4
6
6
7
7
7
7
8
8
2
2
2
5
7
9
10
10
10
10
11
11
14,5
273
273
244
214
190
6
12
2
B
15
15
15
15
15
16
16
15
15
13A
15
14
H
13F
F
G
15
15
15
18
18
18
18
18
18
18
18
18
18
M
X
X
20
20
19
19
18
17A
17B
SAFEGUARDING THE ENVIRONMENT
1. Packing
The packing materials are 100% recyclable and are marked
with the recycling symbol . Comply with local
regulations for disposal. The packing materials (plastic bags,
polystyrene parts, etc.) are a potential source of danger and
must be kept out of the reach of children.
2. Product
This appliance is marked in compliance with European
Directive 2002/96/EC on Waste Electrical and Electronic
Equipment (WEEE).
By ensuring that this appliance is correctly scrapped, the
user can help prevent potentially harmful consequences for
the environment and the health of persons.
The symbol on the product or the accompanying
documentation indicates that it should not be treated as
domestic waste but must be taken to a suitable collection
centre for the recycling of electrical and electronic
equipment.
Disposal must be carried out in compliance with local
regulations on waste disposal.
For further information on the treatment, recovery and
recycling of this product, contact your competent local office,
the household waste collection service or the shop where you
purchased the appliance.
PRECAUTIONS AND GENERAL
RECOMMENDATIONS
IMPORTANT!
• The appliance is not intended for use by children
or persons with limited physical, sensory or
mental abilities or without experience and
knowledge of it, unless they are under the
supervision of or instructed in its use by a person
responsible for their safety.
• Children must be supervised so that they do not
play with the appliance.
1. Do not connect the appliance to the mains power supply
until installation has been completed. Always disconnect
the hood before any cleaning or maintenance, by
unplugging it or turning off the main switch in the home.
2. Do not “flambé” food under the hood. Naked flames
could cause a fire.
3. Do not leave pans unattended when frying, since the
cooking oil could catch fire.
4. Regular cleaning and maintenance is essential for correct
hood operation and good performance. Regularly clean all
deposits from dirty surfaces. Regularly remove and clean
or change the filter. Do not use flammable materials to
duct the extracted air.
5. If the hood is used together with other appliances
operating on gas or other fuels, the negative pressure in
the room must not exceed 4Pa (4 x 10
-5
bar). Therefore,
make sure the room is adequately ventilated.
6. The air extracted by the hood must not be removed
through the flue of the heating system or other appliances
that use gas or other fuels.
7. The room must be adequately ventilated when the hood is
used together with appliances operating on gas or other
fuels.
8. Make sure lamps are cold before touching them.
9. The discharge air must not be ducted in a flue used for
removing fumes produced by appliances operating on
gas or other fuels, but must have a separate outlet. All
national regulations on air discharge must be observed.
10. The hood is not a shelf, therefore do not overload or
place objects on it
Note:
Always wear work gloves for all installation and
maintenance operations.
Electrical connection
The mains power supply must match the voltage given on
the appliance rating plate located inside the hood. If
provided with a plug, connect the hood to a power socket
complying with current regulations and located in an
accessible place. If it does not have a plug (direct connection
to the power supply) or if the socket is not in an accessible
place, fit a suitable double-pole switch that ensures
complete disconnection from the power supply in category
III overvoltage conditions, complying with the installation
rules.
IMPORTANT: Before reconnecting the hood circuit to
the power supply and checking correct operation,
always make sure the power cable is correctly fitted
and that it was NOT crushed in its housing during
installation.
Cleaning the hood
Warning!
Failure to remove oil/grease (at least once a month)
could result in fire.
Use a soft cloth with a neutral detergent. Never use
abrasive substances or alcohol.
Before using the hood
To ensure best use of your hood, please read these
instructions carefully and keep them for future reference.
The packing materials (plastic bags, polystyrene parts, etc.)
are a potential source of danger and must be kept out of the
reach of children.
Make sure the hood was not damaged during transport.
Declaration of conformity
This product has been designed, manufactured and put on
the market in conformity with the following:
- safety objectives of “Low Voltage” Directive
2006/95/EC (which replaces 73/23/EEC as amended)
- protection requirements of “EMC” Directive
89/336/EEC amended by Directive 93/68/EEC.
Troubleshooting guide
The hood does not work:
• Is the plug properly inserted in the power socket?
• Is there a power failure?
The hood is not extracting enough:
• Is the right speed selected?
• Do the filters need cleaning or changing?
• Are the air outlets blocked?
The light does not work:
• Does the lamp need replacing?
• Is the lamp correctly fitted?
AFTER-SALES SERVICE
Before calling the After-Sales Service
1. Check to see if you can fix the problem yourself (see
“Troubleshooting Guide”).
2. Switch the hood off and then on again to check if the
problem has been eliminated.
3. If the problem persists, contact the After-Sales Service.
Specify:
• the type of problem,
• the product model given on the dataplate inside the
hood, visible on removing the grease filters.
• your full address,
• your telephone number and area code.
• the Service code (the number under the word SERVICE
on the dataplate inside the hood, behind the grease
filter).
If any repairs are necessary, contact an authorised Service
Centre (to ensure the use of original spare parts and correct
repair).
Failure to comply with these instructions can compromise
the safety and quality of the product.
The hood is designed for use in “Extractor version” or
in “Filter version”
Extractor version
Fumes are extracted and expelled to the outside
through an exhaust pipe (not supplied) fixed to the
hood coupling ring.
Depending on the exhaust pipe purchased, provide
for suitable fixing to the coupling ring.
Important: If already installed, remove the carbon
filter/s.
Filter version
Air is filtered through a carbon filter/s and recycled
into the surrounding environment.
Important
: Ensure that air recirculation is facilitated
(carefully follow the instructions given in the
installation handbook)
Important!
If the hood does not have a carbon filter/
s, it/they must be ordered and fitted before use.
The hood is provided with hardware (e.g. screws and/or
plugs) suitable for most walls/ceilings. However, it is
necessary to contact a qualified technician to ensure
suitability according to the type of wall/ceiling. The wall/
ceiling must be strong enough to take the weight of the
hood.
Very heavy product; hood handling and
installation must be carried out by at least two
persons.
INSTALLATION - ASSEMBLY
INSTRUCTIONS
Disconnect the power supply at the main panel in the
home when making the electrical connection.
1.
Adjust the extension of the hood support
structure, as the final height of the hood depends
on this.
2.
Fix the two sections of the structure using 8
screws.
3.
Place the ceiling drilling diagram directly above
the cooktop (the centre of the diagram must
match the centre of the cooktop and the edges
must be parallel to the sides of the cooktop - the
side of the diagram with the wording FRONT
corresponds to the control panel side). Prepare
the electrical connection.
4.
Drill as shown (6 holes for 6 wall plugs - 4 plugs for
hooking), screw 4 screws in the outer holes,
leaving a space of about 1 cm between the screw
head and the ceiling.
5.
Fit an exhaust pipe inside the truss and connect it to
the motor compartment coupling ring (exhaust
pipe and fixing clamps are not provided).
6.
Hook the truss on the 4 screws (see step 4).
IMPORTANT! The side of the truss with
connection box corresponds to the side of the
control panel with hood assembled.
7.
Tighten the 4 screws.
8.
Insert and tighten another 2 screws in the
remaining free holes to secure fixing.
9.
Carry out the electrical connection to the
household mains; switch on the power only after
installation.
10.
Hook the hood on the truss, check perfect
hooking - to hook the hood on the truss, partially
screw in 4 screws (also see step 12).
11.
Fixing the hood to the truss with two screws will
also facilitate centering the two parts.
12.
Tighten the 4 screws fixing the truss to the hood.
13.
For extractor operation (13A), connect the other
end of the exhaust pipe to the discharge device in
the home.
For filter operation (13F), fit the deflector F on
the truss and fix it to the special bracket with 4
screws, then connect the exhaust pipe to the
coupling ring on the deflector.
14.
Fit the nuts supplied with fixing hooks inside
the top
and bottom sections of the flues at the rectangular
slots; a total of 10 nuts must be fitted.
15.
Join the two top sections of the flue to cover the
truss so that one of the slots on the sections is on
the same side as the control panel and the other is
on the opposite side.
Screw the two sections with 8 screws and spring
clips (4 each side - see the plan diagram for joining
the two sections).
16.
Fix the top flue assembly to the truss, near the
ceiling, with two screws (one each side).
17.
Carry out electrical connection of the control
panel and lamps (17A or 17B depending on the
model).
18.
Join the two bottom sections of the flue covering
the truss, using 6 screws and spring clips (3 each
side - also see the plan diagram for joining the two
sections).
19.
Insert the bottom section of the flue in the special
seat to completely cover the motor compartment
and electrical connection box, and fix it with two
screws from inside the hood.
20.
Apply the 2 tabs (supplied) to cover the fixing
points of the bottom flue sections (IMPORTANT!
THE TABS FOR THE BOTTOM FLUE ARE THE
NARROWER AND LESS DEEP ONES). The
wider and deeper tabs are those used for the top
flue, and must be cut to size.
21.
Switch the power on again at the main electrical
panel and check correct hood operation.
IF NL E PGBD GR
Description of hood
Fig.1
1.
Control panel.
2.
Grease filter.
3.
Halogen lamps.
4.
Steam deflector.
5.
Telescopic flue.
6.
Perimeter extraction panel
Maintenance
ALWAYS disconnect the hood from the power
supply.
Once a month wash the
grease filter
and the
carbon
filter
in a dishwasher at the highest temperature,
using a normal dishwasher detergent. It is advisable to
wash the filters separately.
After washing, reactivate
the carbon filter
by drying
it in the oven at 100° C for 10 minutes. Change carbon
filter every 3 years.
Remove the perimeter extraction
panel - Fig.2
The perimeter extraction panel is secured in place
with two front pins and two rear hooks.
To open and remove the perimeter extraction panel,
grip the edge of the panel at the front (control side)
and,
guiding it in opening
, pull hard downwards.
Then unscrew the bushings (
s - Fig. 2
) and remove
the panel from the opposite side.
Proceed in reverse order to refit.
Clean the perimeter extraction panel as often as
the grease filter
, using a cloth and a not too
concentrated liquid detergent.
Never use abrasive substances.
Remove the grease filters - Fig. 1:
pull the spring
release handle backwards (
f1
) then remove the filter
downwards (
f2
).
Replacing lamps
1.
Use a small screwdriver or another suitable tool
to prise (
m-Fig. 1
) and remove the lighting unit
(
p-Fig.1
).
2.
Replace the damaged lamp.
Only use 20 W max. (12V-G4) halogen lamps,
taking care not to touch them with hands.
3.
Close the lighting unit (snap-on).
Fitting the carbon filter:
1.
Remove the grease filter (
f1/f2 - Fig. 1
).
2.
Remove the filter holder, turning the knobs 90°
(
g - Fig. 3
).
3.
Fit the carbon filter (
i - Fig. 3
) in the filter holder
(
h - Fig. 3
).
Proceed in reverse order to refit the filter holder and
grease filter.
Control panel
6
5
4
3
2
1
m
p
f1
f2
s
Fig. 1
Fig. 3
Fig. 3
Fig. 2
IF NL E PGBD GR
A.
Light ON/OFF switch.
B.
ON/OFF and speed 1 selector switch
(small amount of steam and fumes).
B+C.
Speed 2 selector switch (medium amount
of steam and fumes).
B+D.
Speed 3 selector switch
(large amount of steam and fumes).
/