Whirlpool AKR 938 IX Program Chart

Brand: Whirlpool

Model: AKR 938 IX

Category: Cooker hoods

Type: Program Chart

The Whirlpool AKR 938 IX is a high-performance cooker hood designed to efficiently remove cooking odors and grease from your kitchen. With four extraction speed settings, including a maximum extraction speed for intensive cooking, you can customize the hood's performance to your needs. The halogen bulbs provide bright illumination for your cooking surface, while the grease filter is removable and dishwasher safe for easy cleaning.



5019 318 33001

AKR 938

INSTALLATIONSANGABEN

Mindestabstand zur Kochfläche: 60 cm (Elektroplatten), 75 cm (Gas-, Öl- oder

Kohleflammen). Folgen Sie bei der Installation der Nummerierun (1

....)

und den jeweiligen Anleitungen. Schließen Sie das Gerät erst nach erfolgter

Installation an die Stromversorgung an. Den Stecker der Dunstabzugshaube

müssen Sie mit einer normgerechten und gut zugänglichen Steckdose verbinden.

Ist die Dunstabzugshaube nicht mit Stecker versehen (direkter Netzanschluss),

müssen Sie einen zweipoligen, normgerechten und gut zugänglichen Schalter mit

Kontakten im Abstand von mindestens 3 mm einbauen.

INSTALLATION SHEET

Minimum height above cooker: 60 cm (electric cookers), 75 cm (gas, gas oil or

coal cookers). To assemble follow the numbers (1

.....) and relative

instructions. Do not connect the appliance to the electrical power supply until

installation is completed. If the appliance is fitted with a power plug connect

the hood to a socket complying with current standards and located in an easily

accessible point. If the appliance does not have a plug (direct connection to the

power supply) fit a two-pole switch to standards, with minimum break distance

between contacts of 3 mm (easily accessible).

FICHE D'INSTALLATION

Distance minimale par rapport à la cuisinière : 60 cm (cuisinière électrique),

75 cm (cuisinière à gaz, mazout ou charbon). Pour le montage, suivez la

numérotation (1

.....) et les instructions correspondantes. Ne branchez

pas l'appareil tant que l'installation n'est pas terminée. Si l'appareil est muni

d'une fiche, branchez-la dans une prise conforme aux normes en vigueur,

installée dans un endroit facile d'accès. Si la hotte est dépourvue de fiche

(branchement direct sur le réseau), appliquez un interrupteur bipolaire

conforme aux normes, ayant une ouverture minimale de 3 mm (accessible).

INSTALLATIEKAART

Minimumafstand tot het kooktoestel: 60 cm (elektrische kooktoestellen), 75 cm

(kooktoestellen op gas, olie of kolen). Volg voor de montage de nummering

.....) en de bijbehorende aanwijzingen. Geef het apparaat geen stroom

totdat de installatie geheel voltooid is. Als het apparaat voorzien is van een

stekker, moet de wasemkap worden aangesloten op een stopcontact dat aan de

geldende voorschriften voldoet en op een goed bereikbare plaats zit. In het geval

dat de kap geen stekker heeft (directe aansluiting op het elektriciteitsnet) dient

u een tweepolige schakelaar te gebruiken met een afstand tussen de contacten van

minstens 3 mm, die aan de geldende voorschriften voldoet (en bereikbaar is).

31833001.fm5 Page 1 Wednesday, March 28, 2001 4:28 PM

Page is loading ...



AKR 938

5019 318 33001

31833001.fm5 Page 3 Wednesday, March 28, 2001 4:28 PM



5019 318 33001

AKR 938

31833001.fm5 Page 4 Wednesday, March 28, 2001 4:28 PM

Page is loading ...



5019 318 33001

AKR 938

Preliminary information for installing the hood:

Expansion plugs are provided to secure the hood to most types of ceilings. However, a qualified technician

must verify suitability of the materials in accordance with the type of ceiling. The ceiling must be strong

enough to take the weight of the hood.

During electrical connection ensure the power supply is disconnected at the domestic main switch.

1. Adjust extension of the hood support structure, as the final height of the hood depends on this, and

remember that with installation completed the hood must be at least 60 cm above the cook-top for

electric cookers and 75 cm for gas or mixed cookers.

2. Fix the two sections of the structure using 8 screws.

3. Place the ceiling hole diagram directly above the cooktop (the centre of the diagram must match the

centre of the cooktop and the edges must be parallel to the sides of the cooktop - the side of the diagram

with the wording FRONT corresponds to the control panel side). Prepare the electrical connection.

4. Drill as shown (6 holes for 6 wall plugs - 4 plugs for fixture), screw the outer screws using the key supplied)

leaving a space of about 1 cm. between the screw head and the ceiling.

5. Fit an exhaust pipe inside the truss and connect it to the motor compartment connection ring (exhaust

pipe and fixing brackets are not supplied).

6. Hook the frame onto the 4 screws (see step 4).

CAUTION! The side of the truss with connection box corresponds to the side of the control panel with

hood assembled.

7. Tighten the 4 screws.

8. Insert and tighten another 2 screws in the remaining free holes for secure fixing.

9. Carry out the electrical connection to the mains power supply, only turn on the power supply upon

completion of assembly.

10.Hook the hood onto the truss, ensuring it fits properly - to hook the hood onto the truss partially tighten

4 screws (see illustrations 10 and 12).

11.Secure the hood to the truss using two screws; this will also help centre the two sections.

12.Tighten the 4 screws securing the truss to the hood.

13.For extractor versions (13A), connect the other end of the exhaust pipe to the flue.

For filter versions (13F), fit deflector F to the truss and secure it to the bracket supplied using 4 screws,

then connect the exhaust pipe to the connection ring located on the deflector.

14.Fit the nuts with fixing hooks supplied inside

the top and bottom sections of the flues at the rectangular

slots. A total of 10 nuts must be fitted.

15.Join the two top sections of the flue to cover the truss so that one of the slots on the sections is situated

on the same side of the control panel and the other on the opposite side.

Screw the two sections together with 4 screws (2 each side - see the plan diagram for joining the two

sections).

16.Fix the top flue assembly to the truss, near the ceiling, with two screws (one each side).

17.Carry out electrical connection of control panel (17a) and bulbs (17b).

18.Join the two bottom sections of the flue covering the truss (16a - the part with the control panel

corresponds to the front of the hood and must be fitted on the same side of the connection box M) using

6 screws (16b - 3 each side, see the plan diagram for joining the two sections).

19.Insert the bottom section of the flue in its seat so that it completely covers the motor compartment and

electrical connection box, then secure it from inside the hood using two screws.

20.Apply the 2 tabs (supplied) to cover the fixing points of the bottom flue (CAUTION! THE BOTTOM FLUE

TABS ARE THE NARROWER AND SHALLOWER ONES).

The wider and deeper tabs are those used for the top flue, and must be cut to size.

21.Turn the mains power on again at the central electrical panel and check for correct hood operation.

INSTALLATION-ASSEMBLY INSTRUCTIONS

F NL E PD GRI

31833001.fm5 Page 8 Wednesday, March 28, 2001 4:28 PM



5019 318 33001

AKR 938

1. Control panel

a. Light ON/OFF switch.

b. Extraction and minimum extraction speed

ON/OFF switch.

c. Medium extraction speed switch.

d. Maximum extraction speed switch.

2. Grease filter.

3. Grease filter handle.

4. Halogen bulbs.

5. Telescopic flue.

6. Steam deflector screen.

To clean the grease filter

Wash the grease filter at least once a month.

1. Disconnect the electrical power supply.

2. Remove the grease filters - Fig. 1: pull the spring

release handle (f) downwards, then remove the

filter.

3. After cleaning the grease filter refit in reverse

order, making sure the entire extraction surface is

covered.

Replacing bulbs

1. Disconnect the electrical power supply.

2. Use a small screwdriver or any other suitable tool

to prise off (m - Fig. 2) the lamp cover (p - Fig. 2).

3. Replace the burnt-out bulb.

Use 20 W max halogen bulbs only, taking care not

to touch them with hands.

4. Close the lighting unit (snap-close).

Carbon filter Fitting and Maintenance

Fitting the carbon filter:

1. Disconnect the electrical power supply.

2. Remove the grease filter (f - Fig. 1).

3. Remove the screw and then the filter holder

(g - Fig. 3).

4. Fit the carbon filter (h - Fig. 3) in the filter holder

(i - Fig. 3).

5. Refit the filter holder and secure it to the hood

with the screw (g - Fig. 3).

6. Refit the grease filter.

Carbon filter maintenance:

Unlike traditional carbon filters, this carbon filter can

be washed and reactivated.

With normal hood use, the filter should be cleaned

once a month. The best way to clean the filter is in a

dishwasher at the highest temperature possible, using

a normal dishwasher detergent. To avoid particles of

food or dirt settling on the filter during washing and

giving rise to unpleasant smells, it is advisable to wash

the filter on its own. After washing, dry the filter in the

oven at 100° C for 10 minutes to reactivate it.

The filter will retain its odour-absorbing capacity for

three years, after which it must be replaced.

FIG. 1 FIG. 2

FIG. 3

F NL E PD GRI

PRODUCT SHEET

31833001.fm5 Page 9 Wednesday, March 28, 2001 4:28 PM

Whirlpool AKR 938 IX Program Chart

Brand: Whirlpool

Model: AKR 938 IX

Category: Cooker hoods

Type: Program Chart

Download PDF

report

Whirlpool AKR 938 IX Program Chart

Whirlpool AKR 938 IX Program Chart

Related papers

Other documents