2. Altronix
  3. TROVE TDMD2
TROVE TDMD2

Altronix TROVE TDMD2 Installation guide

  • Hello! I am an AI chatbot trained to assist you with the Altronix TROVE TDMD2 Installation guide. I’ve already reviewed the document and can help you find the information you need or explain it in simple terms. Just ask your questions, and providing more details will help me assist you more effectively!
Rev. TDMD2062119
TDMD2
- DMP door backplane for Trove2 and Trove3
Installation Guide
All registered trademarks are property of their respective owners. More than just power.™
Installing Company: _____________________ Service Rep. Name: __________________________________________
Address: ________________________________________________________ Phone #: _________________________
Access & Power Integration
- 2 - TDMD2 - DMP Door Backplane
DMP
714-8 0r 714-16
DMP
714-8 0r 714-16
DMP
714-8 0r 714-16
DMP
XR150 orXR550
Bracket
Pem
Standoff
DMP Board
Backplane
Pan Head
Screw
Step 1Step 2
Pan Head Screw
Back of TDMD2
Lock Nut
Step 3
XR150 or XR550
Mounting Bracket
XR150 or XR550
Fig. 1a
Fig. 1b
Overview:
TDMD2 accommodates a combination of the following DMP boards: one (1) XR150 or XR550 board and up to three (3) multi-zone 714
expansion boards for up to forty-eight (48) zones.
Specifications:
• 16 Gauge backplane.
Dimensions (H x W x D): 23.75” x 18.125” x 0.3125” (603.3mm x 460.3mm x 7.9mm).
Hardware:
TDMD2: Configuration of DMP Boards:
1. Mounting 714 expansion boards:
a. Fasten standoffs (provided) into a corresponding pem configuration of backplane (Fig. 1, pg. 2).
b. Mount boards to standoffs utilizing 5/16” pan head screws (provided) (Fig. 1a, pg. 2).
2. Mounting XR150 or XR550 board utilizing a bracket (provided):
a. Push two (2) pan head screws (provided) through the corresponding holes from the back of the backplane (Fig. 1b, pg. 2, Step 1).
b. Mount bracket with slits to the left on screws and secure it with two (2) lock nuts (provided) (Fig. 1b, pg. 2, Step 2).
c. Fasten two (2) standoffs (provided) onto the mounting pems.
d. Orient DMP XR150 or XR550 so the terminal block is to the left. Slide the opposite edge of the board into the bracket’s slits
(Fig. 1b, pg. 2, Step 3) and secure the board to standoffs with two (2) pan head screws (provided).
3. Mount backplane to enclosure’s door with hardware.
Nylon Standoff | 5/16” Pan Head Screw | Lock Nut
Fig. 1
TDMD2 - DMP Door Backplane - 3 -
Notes:
- 4 - TDMD2 - DMP Door Backplane
TDMD2 Backplane Dimensions (H x W x D):
23.75” x 18.125” x 0.3125” (603.3mm x 460.3mm x 7.9mm)
13.7”
(350mm)
13.7”
(350mm)
7.4”
(188mm)
8”
(203.2mm)
7.85”
(199.4mm)
7.5”
(190.5mm)
18.125”
(460.3mm)
10.82”
(274.8mm)
2.075”
(52.7mm)
23.75”
(603.3mm)
0.45”
(11.4mm)
8.7”
(221mm)
11.8”
(299.7mm)
8.7”
(221mm)
0.156”
( 4mm)
Altronix is not responsible for any typographical errors.
140 58th Street, Brooklyn, New York 11220 USA | phone: 718-567-8181 | fax: 718-567-9056
web site: www.altronix.com | e-mail: [email protected] | Made in U.S.A.
IITDMD2 F21S
MEMBER
/