Altronix Trove2KA2 Installation guide

Brand: Altronix

Model: Trove2KA2

Type: Installation guide

The Altronix Trove2KA2 is an enclosure designed to accommodate various combinations of Keyscan boards with or without Altronix power supplies and accessories for access systems. It features a tamper switch, cam lock, and mounting hardware for secure installation. The enclosure has dimensions of 27.25" x 21.75" x 6.5" and can accommodate a combination of Altronix modules, such as the AL400ULXB2, AL600ULXB, AL1012ULXB, AL1024ULXB2, eFlow4NB, eFlow6NB, eFlow102NB, or eFlow104NB, and one T16100, ACM4(CB), ACM8(CB), MOM5, PD4UL(CB), PD8UL(CB), PDS8(CB), or VR6 module.

SIGNALING

Rev. TKA042816

Installing Company: _____________________ Service Rep. Name: __________________________________________

Address: ________________________________________________________ Phone #: _________________________

Access & Power Integration

Trove2KA2

- Trove2 enclosure with Altronix/Keyscan backplane (TKA2)

TKA2

- Altronix/Keyscan backplane only

Trove3KA3

- Trove3 enclosure with Altronix/Keyscan backplane (TKA3)

TKA3

- Altronix/Keyscan backplane only

Installation Guide

All registered trademarks are property of their respective owners. More than just power.™

- 2 - Trove2KA2 / Trove3KA3

Overview:

Trove2KA2/Trove3KA3 accommodates various combinations of Keyscan boards with or without Altronix power supplies and accessories for

access systems.

Specifications:

Agency Listings:

• UL 294 - 6th edition: Line Security I, Destructive Attack I, Endurance IV, Stand-by Power II*.

*Stand-by Power Level I if no battery is supplied.

• This Class B digital apparatus complies with Canadian ICES-003.

Cet appareil numérique de la classe B est conforme á la norme NMB-003 du Canada.

• CE European Conformity.

Installation Instructions for Trove2/Trove3:

1. Remove backplane from enclosure prior to mounting (do not discard hardware).

2. Mark and predrill holes in the wall to line up with the top keyholes in the enclosure. Install the upper fasteners and screws in the wall

with the screw heads protruding. Place the enclosure’s upper keyholes over the screws; level and secure.

Mark the position of the lower holes. Remove the enclosure. Drill the lower holes and install the fasteners.

Place the enclosure’s upper keyholes over the upper screws. Install the lower screws and make

sure to tighten all screws (Enclosure Dimensions, pg. 6, 8).

3. Mount included UL Listed tamper switch (Altronix Model TS112 or equivalent) in desired location,

opposite hinge. Slide the tamper switch bracket onto the edge of the enclosure approximately 2”

from the right side (Fig. 1, pg. 2). Connect tamper switch wiring to the Access Control Panel

input or the appropriate UL Listed reporting device.

To activate alarm signal open the door of the enclosure.

4. Mount Altronix/Keyscan boards to backplane, refer to pages 3, 4.

Hardware:

Nylon Standoff | Metal Standoff | Pan Head Screw | Lock Nut

Trove2KA2

Trove2 enclosure with TKA2 Altronix/Keyscan backplane

• Includes: tamper switch, cam lock, and mounting hardware.

Enclosure Dimensions (H x W x D):

27.25” x 21.75” x 6.5” (692.2mm x 552.5mm x 165.1mm).

TKA2

Altronix/Keyscan backplane only

• Includes mounting hardware.

Dimensions (H x W x D):

25.375” x 19.375” x 0.3125” (644.5mm x 482.6mm x 7.9mm).

TKA2 accommodates a combination of the following:

Altronix Modules:

• One (1) AL400ULXB2, AL600ULXB, AL1012ULXB,

AL1024ULXB2, eFlow4NB, eFlow6NB, eFlow102NB, or

eFlow104NB.

• One (1) T16100, ACM4(CB), ACM8(CB), MOM5, PD4UL(CB),

PD8UL(CB), PDS8(CB), VR6.

Keyscan Modules:

• One (1) CA250B, CA4500B, CA8500B, one (1) DPS-15,

one (1) CIM.

• Two (2) OCB8

Trove3KA3

Trove3 enclosure with TKA3 Altronix/Keyscan backplane

• Includes: (2) tamper switches, cam lock, and mounting hardware.

Enclosure Dimensions (H x W x D):

36.12” x 30.125” x 7.06” (917.5mm x 768.1mm x 179.3mm).

TKA3

Altronix/Keyscan backplane only

• Includes mounting hardware.

Dimensions (H x W x D):

34” x 28” x 0.3125” (863.6mm x 711.2mm x 7.9mm).

TKA3 accommodates a combination of the following:

Altronix Modules:

• One (1) AL400ULXB2, AL600ULXB, AL1012ULXB,

AL1024ULXB2, eFlow4NB, eFlow6NB, eFlow102NB, or

eFlow104NB.

• One (1) T16100, ACM4(CB), ACM8(CB), MOM5, PD4UL(CB),

PD8UL(CB), PDS8(CB), VR6.

Keyscan Modules:

• Two (2) CA250B, CA4500B, CA8500B, two (2) DPS-15,

two (2) CIM.

• Four (4) OCB8

Fig. 1

Tamper Switch

(provided)

To Access Control Panel or

UL Listed Reporting Device

Edge of

Enclosure

Trove2KA2 / Trove3KA3 - 3 -

Altronix

Power Supply

Altronix

Power Supply or

Sub-Assembly

Altronix

T16100

Metal Standoff Placement Metal Standoff Placement

Keyscan

CA250B,

CA4500B

CA8500B

Keyscan

DPS15

Keyscan

CIM

Keyscan

OCB8

Keyscan

OCB8

Locknut

TKA2: Configuration of Altronix Power Supply

and/or Sub-Assembly Boards and Keyscan Boards

1. Fasten metal and snap on standoffs (provided) to pems which match the hole pattern for Altronix Power Supply/Chargers or Altronix

Sub-Assembly boards (Fig. 2, 2a, pg. 3). Note: Please fasten metal and snap on standoffs in the proper locations (Fig. 2, pg. 3).

2. Mount boards to standoffs utilizing 5/16” pan head screws (provided) (Fig. 2, pg. 3).

3. Mount Altronix T16100 transformer to backplane using two locking nuts (Fig. 2, pg. 3).

4. Mount appropriate Keyscan boards into the correct positions (Fig. 2, pg. 3) by postioning standoffs over appropriate holes on the

backplane and depress down on board to secure standoff to the backplane (Fig. 2b, pg. 3).

5. Fasten backplane to Trove2 enclosure utilizing pan head screws (provided).

Fig. 2

Plastic Standoff

pre-mounted into

Keyscan modules

Insert into

TKA2 or

TKA3 backplane

Nylon or

Metal

Standoff

Sub-Assembly

Backplane

Pem

Fig. 2a

Fig. 2b

- 4 - Trove2KA2 / Trove3KA3

Keyscan

CA250B,

CA4500B,

CA8500B

Keyscan

DPS15

Keyscan

DPS15

Keyscan

CIM

Keyscan

OCB8

Keyscan

OCB8

Keyscan

CA250B,

CA4500B,

CA8500B

Keyscan

CIM

Keyscan

OCB8

Keyscan

OCB8

Altronix

Power Supply or

Sub-Assembly

Altronix

Sub-

Assembly

Altronix

Power Supply or

Sub-Assembly

Altronix

Power Supply or

Sub-Assembly

Altronix

Sub-Assembly

Altronix

Sub-Assembly

Altronix

T16175

Metal Standoff Placement

Locknut

Metal Standoff Placement

TKA3: Configuration of Altronix Power Supply

and/or Sub-Assembly Boards and Keyscan Boards

1. Fasten metal and snap on standoffs (provided) to pems which match the hole pattern for Altronix Power Supply/Chargers or Altronix

Sub-Assembly boards (Fig. 3, 3a, pg. 4). Note: Please fasten metal and snap on standoffs in the proper locations (Fig. 3, pg. 4).

2. Mount boards to standoffs utilizing 5/16” pan head screws (provided) (Fig. 3, pg. 4).

3. Mount Altronix T16175 transformer to backplane using four locking nuts and TKA3BK: tighten top two lock nuts first, then, utilizing

the TKA3BK bracket, insert pems through T16175 feet and backplane and tighten locknuts to the pems protruding through the

backplane. (Fig. 3b, pg. 4).

4. Mount appropriate Keyscan boards into the correct positions (Fig. 3, pg. 4) by postioning standoffs over appropriate holes on the

backplane and depress down on board to secure standoff to the backplane (Fig. 3c, pg. 4).

5. Fasten backplane to Trove3 enclosure utilizing pan head screws (provided).

Fig. 3

Plastic Standoff

pre-mounted into

Keyscan modules

Insert into

TKA2 or

TKA3 backplane

TKA3

Lock Nut

Mounting

Hole

Mounting Bracket

Terminals

T16175

Nylon or

Metal

Standoff

Sub-Assembly

Backplane

Pem

Fig. 3a

Fig. 3b

Fig. 3c

Trove2KA2 / Trove3KA3 - 5 -

7.5”

(190.5mm)

7.5”

(190.5mm)

7.5”

(190.5mm)

25.375”

(644.6mm)

19.375”

(492.1mm)

12.625”

(320.7mm)

0.45”

(11.4mm)

1.0” (25.4mm)

9.2”

(

233.7mm

)

8.5”

(215.9mm)

16.25”

(412.8mm)

0.156”

( 3.96mm)

9.2”

(

233.7mm

)

7.5”

(190.5mm)

0.45”

(11.4mm)

TKA2 Dimensions (H x W x D):

25.375” x 19.375” x 0.3125” (644.6mm x 492.1mm x 7.9mm)

- 6 - Trove2KA2 / Trove3KA3

Trove2KA2 Enclosure Dimensions (H x W x D approximate):

27.25” x 21.75” x 6.5” (692.15mm x 546.1mm x 165.1mm)

1.25”

(31.75mm)

1.25”

(31.75mm)

6.25”

(158.75mm)

6.25”

(158.75mm)

6.75”

(171.45mm)

8.25”

(209.54mm)

8.00”

(203.2mm)

1.5”

(38.1mm)

1.25”

(31.75mm)

0.85”

(21.59mm)

0.85”

(21.59mm)

1.00”

(25.4mm)

2.00”

(50.8mm)

1.25”

(31.75mm)

2.00”

(

50.8mm

)

2.00”

(

50.8mm

)

5.25”

(

133.35mm

)

5.25”

(

133.35mm

)

7.00”

(

177.79mm

)

2.00”

(50.8mm)

2.00”

(50.8mm)

27.00”

(685.8mm)

3.50”

(88.9mm)

0.5625”

(14.29mm)

2.415”

(61.34mm)

0.685”

(17.399mm)

1.77”

(44.96mm)

3.50”

(88.9mm)

21.50”

(546.1mm)

19.80”

(502.92mm)

5.25”

(133.35mm)

5.25”

(133.35mm)

0.885” (22.479mm)

1.125” (28.32mm)

Knockouts

- 7 - Trove2KA2 / Trove3KA3

TKA3 Dimensions

34” x 28” x 0.3125” (863.6mm x 711.2mm x 7.9mm)

23” (584.2mm)

27” (685.8mm)

11.5” (292.1mm)

6.5” (165.1mm)

8.55” (217.2mm)

28” (711.2mm)

34” (863.6mm)

11.5” (292.1mm)

- 8 - Trove2KA2 / Trove3KA3

Altronix is not responsible for any typographical errors.

140 58th Street, Brooklyn, New York 11220 USA | phone: 718-567-8181 | fax: 718-567-9056

web site: www.altronix.com | e-mail: [email protected] | Made in U.S.A.

IITrove2KA2/3KA3 K08S

MEMBER

Trove3KA3 Enclosure Dimensions (H x W x D approximate):

36.12” x 30.125” x 7.06” (917.5mm x 768.1mm x 179.3mm)

2.00”

(50.8mm)

8.75”

(222.3mm)

8.75”

(222.3mm)

8.62”

(219mm)

7.06”

(179.3mm)

1.25”

(31.8mm)

1.25”

(31.8mm)

2.00”

(50.8mm)

7.12”

(222.25mm)

9.5”

(241.3mm)

30.12”

(768.1mm)

14.01”

(355.9mm)

14.01”

(355.9mm)

9.5”

(241.3mm)

1.25”

(31.75mm)

1.55”

(39.37mm)

1.78”

(45.21mm)

1.25”

(31.8mm)

1.07”

(27.2mm)

1.10”

(27.9mm)

2.00”

(50.8mm)

10.75”

(273.1mm)

10.75”

(273.1mm)

10.62”

(269.8mm)

2.00”

(50.8mm)

10.75”

(273.1mm)

10.75”

(273.1mm)

10.62”

(269.8mm)

36.12”

(917.5mm)

33.63”

(854.20mm)

Altronix Trove2KA2 Installation guide

Altronix Trove2KA2 Installation guide

Altronix Trove2KA2 Installation guide

Related papers

Other documents