WAGO Field side connection module 16- User manual

Brand: WAGO

Model: Field side connection module 16-

Type: User manual

Pos: 2 /Dokumentation allgemein/Einband/Einband Handbuch - Deckbl at t oh ne V aria nt enfel d (S ta ndar d) @ 9 \mod_1285229289866_0.docx @ 64941 @ @ 1

Manual

WAGO-I/O-SYSTEM 750

Field Side Connection 16-

750-1606

Field Side Connection Module 16-, 0 VDC

Version 1.1.0

Pos: 3 /A lle Ser ien ( All ge mein e M odul e)/ Hin weis e z ur D oku men tati on/I mpr ess um für Sta ndar dh and büch er - allg. A ngabe n, Ansc hrifte n, Tel efonn ummer n und E-M ail-A dress en @ 3\mod_1219151118203_21.docx @ 21060 @ @ 1

2 WAGO-I/O-SYSTEM 750

750-1606 Field Side Connection 16-

Manual

Version 1.1.0

WAGO Kontakttechnik GmbH & Co. KG

Hansastraße 27

D-32423 Minden

Phone: +49 (0) 571/8 87 – 0

Fax: +49 (0) 571/8 87 – 1 69

E-Mail: [email protected]

Web: http://www.wago.com

Technical Support

Phone: +49 (0) 571/8 87 – 5 55

Fax: +49 (0) 571/8 87 – 85 55

E-Mail: [email protected]

Every conceivable measure has been taken to ensure the accuracy and

completeness of this documentation. However, as errors can never be fully

excluded, we always appreciate any information or suggestions for improving the

documentation.

E-Mail: [email protected]

We wish to point out that the software and hardware terms as well as the

trademarks of companies used and/or mentioned in the present manual are

generally protected by trademark or patent.

=== Ende der Lis te f ür T e xtmar ke Ei nb and _vor ne = ==

WAGO-I/O-SYSTEM 750 Table of Contents 3

750-1606 Field Side Connection 16-

Manual

Version 1.1.0

Pos: 5 /D ok ument ati on al lg em ein/V erz eic hni sse /Inh alts ver zei chni s - Ü bersc hrift oG und Ver zeich nis @ 3\mod_1219151230875_21.docx @ 21063 @ @ 1

Table of Contents

1 Notes about this Documentation ................................................................. 5

1.1 Validity of this Documentation ................................................................. 5

1.2 Copyright ................................................................................................... 5

1.3 Symbols ..................................................................................................... 6

1.4 Number Notation ....................................................................................... 8

1.5 Font Conventions ...................................................................................... 8

2 Important Notes ........................................................................................... 9

2.1 Legal Bases ............................................................................................... 9

2.1.1 Subject to Changes ............................................................................... 9

2.1.2 Personnel Qualifications ....................................................................... 9

2.1.3 Use of the WAGO-I/O-SYSTEM 750 in Compliance with

Underlying Provisions .......................................................................... 9

2.1.4 Technical Condition of Specified Devices ......................................... 10

2.2 Safety Advice (Precautions) .................................................................... 11

3 Device Description ..................................................................................... 13

3.1 View ........................................................................................................ 14

3.2 Connectors ............................................................................................... 15

3.2.1 Data Contacts/Internal Bus ................................................................. 15

3.2.2 Power Jumper Contacts/Field Supply ................................................ 16

3.2.3 Push-in CAGE CLAMP

Connectors ................................................ 18

3.3 Display Elements .................................................................................... 18

3.4 Operating Elements ................................................................................. 18

3.5 Schematic Diagram ................................................................................. 19

3.6 Technical Data ........................................................................................ 20

3.6.1 Device ................................................................................................. 20

3.6.2 Supply ................................................................................................. 20

3.6.3 Connection Type ................................................................................ 20

3.6.4 Climatic Environmental Conditions ................................................... 21

3.7 Approvals ................................................................................................ 22

3.8 Standards and Guidelines ........................................................................ 23

4 Mounting ..................................................................................................... 24

4.1 Mounting Sequence ................................................................................. 24

4.2 Inserting and Removing Devices ............................................................ 25

4.2.1 Inserting the I/O Module .................................................................... 25

4.2.2 Removing the I/O Module .................................................................. 26

5 Connect Devices ......................................................................................... 27

5.1 Connecting a Conductor to the Push-in CAGE CLAMP

...................... 27

6 Use in Hazardous Environments .............................................................. 28

6.1 Marking Configuration Examples ........................................................... 29

6.1.1 Marking for Europe According to ATEX and IEC-Ex ...................... 29

6.1.2 Marking for America According to NEC 500 .................................... 34

6.2 Installation Regulations ........................................................................... 35

6.2.1 Special Conditions for Safe Use

(ATEX Certificate TÜV 07 ATEX 554086 X) .................................. 36

4 Table of Contents WAGO-I/O-SYSTEM 750

750-1606 Field Side Connection 16-

Manual

Version 1.1.0

6.2.2 Special Conditions for Safe Use

(ATEX Certificate TÜV 12 ATEX 106032 X) .................................. 37

6.2.3 Special Conditions for Safe Use

(IEC-Ex Certificate TUN 09.0001 X) ................................................ 38

6.2.4 Special Conditions for Safe Use

(IEC-Ex Certificate IECEx TUN 12.0039 X) .................................... 39

6.2.5 Special Conditions for Safe Use According to ANSI/ISA 12.12.01 .. 40

List of Figures ...................................................................................................... 41

List of Tables ........................................................................................................ 42

=== Ende der Lis te f ür T e xtmar ke V erz eic hnis _vor ne == =

WAGO-I/O-SYSTEM 750 Notes about this Documentation 5

750-1606 Field Side Connection 16-

Manual

Version 1.1.0

Pos: 7 /A lle Ser ien ( All ge mein e M odul e)/ Über sc hrif ten für all e Ser ie n/Hi nwei se zur D o kume nt ation /Hi nw eise zu dies er D o kume ntati on - Ü ber schr if t 1 @ 4\ mod_1237987661750_21.docx @ 29029 @ 1 @ 1

1 Notes about this Documentation

Pos: 8 /A lle Ser ien ( All ge mein e M odul e)/ Hin weis e z ur D oku men tati on/H i nweis e/Hi n weis : D okum ent atio n a ufbe wahr e n @ 4 \mod_1237987339812_21.docx @ 29026 @ @ 1

Always retain this documentation!

This documentation is part of the product. Therefore, retain the documentation

during the entire service life of the product. Pass on the documentation to any

subsequent user. In addition, ensure that any supplement to this documentation is

included, if necessary.

Pos: 9 /A lle Ser ien ( All ge mein e M odul e)/ Über sc hrif ten für all e Ser ie n/Hi nwei se zur D o kume ntat ion /Gül tig keit sber eic h - Üb ersc hrif t 2 @ 1 2\mod_1338912448776_21.docx @ 96469 @ 2 @ 1

1.1 Validity of this Documentation

Pos: 10 /S eri e 7 50 ( WA GO-I/ O-SYST EM) /Hi n weis e zur D okum ent ati on/G ülti gkei ts berei c h/Gül tig kei tsber ei ch D oku men tat ion Bus kle mme 75 0-xx xx, o hne Var iant en ang abe @ 14 \mod_1358944037947_21.docx @ 109346 @ @ 1

This documentation is only applicable to the I/O module 750-1606

(Field Side Connection 16-).

Pos: 11 /Serie 750 (WAG O-I/O-S YST EM) /Hi n weise z ur Do kume nt ati on/Hi nw eise /Ac htu ng: H in weis z ur Do ku ment ati on B uskl emm en 750- xxxx @ 4\mod_1237986979656_21.docx @ 29023 @ @ 1

The I/O module 750-1606 shall only be installed and operated according to the

instructions in this manual and in the manual for the used fieldbus

coupler/controller.

Consider power layout of the WAGO-I/O-SYSTEM 750!

In addition to these operating instructions, you will also need the manual for the

used fieldbus coupler/controller, which can be downloaded at www.wago.com.

There, you can obtain important information including information on electrical

isolation, system power and supply specifications.

Pos: 12.1 /All e Seri en ( All ge meine Mo dul e)/H in weis e zur D oku ment ati on/U rh eber sc hutz aus führ lic h @ 4\mod_1235565145234_21.docx @ 27691 @ 2 @ 1

1.2 Copyright

This Manual, including all figures and illustrations, is copyright-protected. Any

further use of this Manual by third parties that violate pertinent copyright

provisions is prohibited. Reproduction, translation, electronic and phototechnical

filing/archiving (e.g., photocopying) as well as any amendments require the

written consent of WAGO Kontakttechnik GmbH & Co. KG, Minden, Germany.

Non-observance will involve the right to assert damage claims.

Pos: 12.2 /Dokumentation allgemein/Gliederungselemente/---Seite nwechs el--- @ 3\ mod_1221108045078_0.docx @ 21810 @ @ 1

6 Notes about this Documentation WAGO-I/O-SYSTEM 750

750-1606 Field Side Connection 16-

Manual

Version 1.1.0

Pos: 12.3 /All e Seri en ( All ge meine Mo dul e)/Ü bers chr ift en f ür alle S erie n/Hi nwei se z ur Dok um enta tio n/S ymbol e - Ü bers chr ift 2 @ 1 3\mod_1351068042408_21.docx @ 105270 @ 2 @ 1

1.3 Symbols

Pos: 12 .4.1 /Al le Seri en (A llg emei ne M od ule) /Wic hti ge Erlä ut erung en/ Sic her heits - und sonstige Hinweise/Gefahr/Gefahr: _Warnung vor Personenschäden allgemein_ - Erläu terung @ 13\mod_1343309450020_21.docx @ 101029 @ @ 1

Personal Injury!

Indicates a high-risk, imminently hazardous situation which, if not avoided, will

result in death or serious injury.

Pos: 12 .4.2 /Al le Seri en (All gemei ne Mod ule)/ Wichti ge Erl äuter unge n/Sich erheit s- und sonsti ge Hinw eise/ Gefa hr/Gef ahr: _ Warnu ng vor Per son enschä den durc h elek trisc hen Str om_ - Erläuterung @ 13\mod_1343309694914_21.docx @ 101030 @ @ 1

Personal Injury Caused by Electric Current!

Indicates a high-risk, imminently hazardous situation which, if not avoided, will

result in death or serious injury.

Pos: 12 .4.3 /Al le Seri en (All gemei ne Mod ule)/ Wichti ge Erl äuter unge n/Sich erheit s- und so nsti ge H inw eis e/W arn ung/ War nung : _ War nu ng vor P erso nens ch äde n all ge mei n_ - Er lä uterung @ 13\mod_1343309877041_21.docx @ 101035 @ @ 1

Personal Injury!

Indicates a moderate-risk, potentially hazardous situation which, if not avoided,

could result in death or serious injury.

Pos: 12 .4.4 /Al le Seri en (All gemei ne Mod ule)/ Wichti ge Erl äuter unge n/Sich erheit s- und so nsti ge H inw eis e/V orsic ht /Vor sic ht: _War nu ng vor P ers one nsc häde n al lg emei n_ - Erläuterung @ 13\mod_1343310028762_21.docx @ 101038 @ @ 1

Personal Injury!

Indicates a low-risk, potentially hazardous situation which, if not avoided, may

result in minor or moderate injury.

Pos: 12 .4.5 /Al le Seri en (All gemei ne Mod ule)/ Wichti ge Erl äuter unge n/Sich erheit s- und sonstige Hinweise/Achtung/Achtung: _Warnung vor Sachschäden allgemein_ - Erläuterung @ 13\mod_1343310134623_21.docx @ 101041 @ @ 1

Damage to Property!

Indicates a potentially hazardous situation which, if not avoided, may result in

damage to property.

Pos: 12 .4.6 /Al le Seri en (All gemei ne Mod ule)/ Wichti ge Erl äuter unge n/Sich erheit s- und sonstige Hinweise/Achtung/Achtung: _Warnung vor Sachschäden durch elektrostatische Aufladung_ - Erläuterung @ 13\mod_1343310227702_21.docx @ 101044 @ @ 1

Damage to Property Caused by Electrostatic Discharge (ESD)!

Indicates a potentially hazardous situation which, if not avoided, may result in

damage to property.

Pos: 12 .4.7 /Al le Seri en (All gemei ne Mod ule)/ Wichti ge Erl äuter unge n/Sich erheit s- und sonstige Hinweise/Hinweis/Hinweis: _Wichtiger Hinweis allgemein_ - Erläuterung @ 13\mod_1343310326906_21.docx @ 101047 @ @ 1

Important Note!

Indicates a potential malfunction which, if not avoided, however, will not result in

damage to property.

Pos: 12 .4.8 /Al le Seri en (All gemei ne Mo dul e)/ Wic htig e Er lä uter ung en/ Sich erh eits- und sons ti ge Hi nw eis e/Inf or mati on/I nf or matio n: _ Wei ter e Inf or mati on allg emei n_ - Erl äuter ung @ 13 \mod_1343310439814_21.docx @ 101051 @ @ 1

WAGO-I/O-SYSTEM 750 Notes about this Documentation 7

750-1606 Field Side Connection 16-

Manual

Version 1.1.0

Additional Information:

Refers to additional information which is not an integral part of this

documentation (e.g., the Internet).

Pos: 12.5 /Dokumentation allgemein/Gliederungselemente/---Seite nwechs el--- @ 3\ mod_1221108045078_0.docx @ 21810 @ @ 1

8 Notes about this Documentation WAGO-I/O-SYSTEM 750

750-1606 Field Side Connection 16-

Manual

Version 1.1.0

Pos: 12.6 /All e Seri en ( All ge meine Mo dul e)/H in weis e zur D oku ment ati on/Z ahl ensy steme @ 3\ mod_1221059454015_21.docx @ 21711 @ 2 @ 1

1.4 Number Notation

Table 1: Number Notation

Number Code

Example

Note

Decimal

100

Normal notation

Hexadecimal

0x64

C notation

Binary

'100'

'0110.0100'

In quotation marks, nibble separated with

dots (.)

Pos: 12 .7 /All e Seri en (Allg emeine Modul e)/Hi nweis e zur Do kument ation /Schr iftko nventi one n @ 3\mod_1221059521437_21.docx @ 21714 @ 2 @ 1

1.5 Font Conventions

Table 2: Font Conventions

Font Type

Indicates

italic

Names of paths and data files are marked in italic-type.

e.g.: C:\Program Files\WAGO Software

Menu items are marked in bold letters.

e.g.: Save

A greater-than sign between two names means the selection of a

menu item from a menu.

e.g.: File > New

Input

Designation of input or optional fields are marked in bold letters,

e.g.: Start of measurement range

“Value”

Input or selective values are marked in inverted commas.

e.g.: Enter the value “4 mA” under Start of measurement range.

[Button]

Pushbuttons in dialog boxes are marked with bold letters in square

brackets.

e.g.: [Input]

[Key]

Keys are marked with bold letters in square brackets.

e.g.: [F5]

Pos: 13 /Doku ment ation all gemei n/Gli eder ungsel eme nte/---Seit en wechs el--- @ 3\mod_1221108045078_0.docx @ 21810 @ @ 1

WAGO-I/O-SYSTEM 750 Important Notes 9

750-1606 Field Side Connection 16-

Manual

Version 1.1.0

Pos: 14 /Alle Ser ien (Al lge meine Mo dule)/ Über schrif ten für alle Ser ien/ Wichti ge Erlä uteru ngen/ Wich tige Er läuter ungen - Übersc hrift 1 @ 4\mod_1241428899156_21.docx @ 32170 @ 1 @ 1

2 Important Notes

Pos: 15.1 /All e Seri en ( All ge meine Mo dul e)/ Wichti ge Erlä uteru ngen/ Wic htige Erl äuter unge n - Einl eitung @ 3\mod_1221059818031_21.docx @ 21717 @ @ 1

This section includes an overall summary of the most important safety

requirements and notes that are mentioned in each individual section. To protect

your health and prevent damage to devices as well, it is imperative to read and

carefully follow the safety guidelines.

Pos: 15.2 /All e Seri en ( All ge meine Mo dul e)/Ü bers chr ift en f ür alle S erie n/Wi chti ge Erl äuter u ngen /Re chtl ich e Gr undl ag en - Ü bers chr ift 2 @ 3\mod_1221060626343_21.docx @ 21726 @ 2 @ 1

2.1 Legal Bases

Pos: 15.3 /All e Seri en ( All ge meine Mo dul e)/ Wic htig e Er läut eru nge n/ Änd erung s vorbe hal t - Ü bers chri ft 3 un d I nhalt @ 3\mod_1221060036484_21.docx @ 21720 @ 3 @ 1

2.1.1 Subject to Changes

WAGO Kontakttechnik GmbH & Co. KG reserves the right to provide for any

alterations or modifications that serve to increase the efficiency of technical

progress. WAGO Kontakttechnik GmbH & Co. KG owns all rights arising from

the granting of patents or from the legal protection of utility patents. Third-party

products are always mentioned without any reference to patent rights. Thus, the

existence of such rights cannot be excluded.

Pos: 15.4 /Serie 750 (WAGO-I/O-SYST EM)/ Wic htige Erl äuter unge n/Pers onalq uali fikati onPer sonal qual ifikation 750-xxxx - Ü bersc hrift 3 u nd Inhal t @ 3\mod_1224061208046_21.docx @ 24063 @ 3 @ 1

2.1.2 Personnel Qualifications

All sequences implemented on WAGO-I/O-SYSTEM 750 devices may only be

carried out by electrical specialists with sufficient knowledge in automation. The

specialists must be familiar with the current norms and guidelines for the devices

and automated environments.

All changes to the coupler or controller should always be carried out by qualified

personnel with sufficient skills in PLC programming.

Pos: 15.5 /Serie 750 (WAGO-I/O-SYSTEM)/Wichtige Erläuterungen/Bestimmungsgemäße VerwendungBestimmungsgemäße Verwendung 750-xxxx - Über schri ft 3 un d I nhal t @ 3\ mod_1224064151234_21.docx @ 24070 @ 3 @ 1

2.1.3 Use of the WAGO-I/O-SYSTEM 750 in Compliance with

Underlying Provisions

Fieldbus couplers, fieldbus controllers and I/O modules found in the modular

WAGO-I/O-SYSTEM 750 receive digital and analog signals from sensors and

transmit them to actuators or higher-level control systems. Using programmable

controllers, the signals can also be (pre-) processed.

The devices have been developed for use in an environment that meets the IP20

protection class criteria. Protection against finger injury and solid impurities up to

12.5 mm diameter is assured; protection against water damage is not ensured.

Unless otherwise specified, operation of the devices in wet and dusty

environments is prohibited.

Operating the WAGO-I/O-SYSTEM 750 devices in home applications without

further measures is only permitted if they meet the emission limits (emissions of

interference) according to EN 61000-6-3. You will find the relevant information

in the section “Device Description” > “Standards and Guidelines” in the manual

for the used fieldbus coupler/controller.

10 Important Notes WAGO-I/O-SYSTEM 750

750-1606 Field Side Connection 16-

Manual

Version 1.1.0

Appropriate housing (per 94/9/EG) is required when operating the WAGO-I/O-

SYSTEM 750 in hazardous environments. Please note that a prototype test

certificate must be obtained that confirms the correct installation of the system in

a housing or switch cabinet.

Pos: 15 .6 /All e Seri en (All ge meine Mo dul e)/ Wic htig e Er läut eru nge n/T ec hnisc her Zus tan d d er G erät e - Ü bersc hrift 3 und Inh alt @ 3\mod_1221060446109_21.docx @ 21723 @ 3 @ 1

2.1.4 Technical Condition of Specified Devices

The devices to be supplied ex works are equipped with hardware and software

configurations, which meet the individual application requirements. WAGO

Kontakttechnik GmbH & Co. KG will be exempted from any liability in case of

changes in hardware or software as well as to non-compliant usage of devices.

Please send your request for modified and new hardware or software

configurations directly to WAGO Kontakttechnik GmbH & Co. KG.

Pos: 15.7 /Dokumentation allgemein/Gliederungselemente/---Seite nwechs el--- @ 3\ mod_1221108045078_0.docx @ 21810 @ @ 1

WAGO-I/O-SYSTEM 750 Important Notes 11

750-1606 Field Side Connection 16-

Manual

Version 1.1.0

Pos: 15 .8 /All e Seri en (All ge meine Mo dul e)/Ü bers chr ift en f ür alle S erie n/Wi chti ge Erl äuter u ngen /Sic her hei tshi nw eise - Üb erschr ift 2 @ 6\mod_1260180299987_21.docx @ 46724 @ 2 @ 1

2.2 Safety Advice (Precautions)

Pos: 15.9 /All e Seri en ( All ge meine Mo dul e)/ Wic htig e Er läut eru nge n/ Sich erh eits- und sons tig e Hi n weise/ Ei nlei tung Si cher hei tshi nw eis e H ardw are @ 6\ mod_1260180170493_21.docx @ 46720 @ @ 1

For installing and operating purposes of the relevant device to your system the

following safety precautions shall be observed:

Pos: 15 .10. 1 /Alle Ser ie n (All ge mei ne M odul e) /Wi chti ge Erl äuter u ngen /Sic her heit s- un d s onsti ge Hin wei se/G ef ahr /Gef ahr: Ni cht an G erät e n un ter Spa nnu ng ar beit en! @ 6\mod_1260180365327_21.docx @ 46727 @ @ 1

Do not work on devices while energized!

All power sources to the device shall be switched off prior to performing any

installation, repair or maintenance work.

Pos: 15.1 0. 2 /S erie 750 ( W AGO -I/O-SY ST EM) /Wic htig e Er l äuter ung en /Sic her hei ts- un d s onsti ge H in wei se/G ef ahr/ Gefa hr: Ei nbau 07 50- xxxx nur in Geh äusen, S chrä nken oder ele ktrisc hen Betr iebsr äume n! @ 6\mod_1260180556692_21.docx @ 46731 @ @ 1

Install the device only in appropriate housings, cabinets or in electrical

operation rooms!

The WAGO-I/O-SYSTEM 750 and its components are an open system. As such,

install the system and its components exclusively in appropriate housings,

cabinets or in electrical operation rooms. Allow access to such equipment and

fixtures to authorized, qualified staff only by means of specific keys or tools.

Pos: 15.1 0. 3 /Al le S eri en ( Allg em ein e Mo dul e)/ Wich tig e Er lä uter ung en/Si ch erh eits- und s ons tig e Hi nw eise /Gef ahr /G efahr : U nfal lv erh ütung sv orsc hri ften bea ch ten! @ 6\mod_1260180657000_21.docx @ 46735 @ @ 1

Pos: 15.1 0. 4 /Al le S eri en ( Allg em ein e Mo dul e)/ Wich tig e Er lä uter ung en/Si ch erh eits- und s ons tig e Hi nw eise /Gef ahr /G efahr : A uf n ormg er echt en A nsc hl uss acht en! @ 6 \mod_1260180753479_21.docx @ 46739 @ @ 1

Pos: 15 .11. 1 /Al le S eri en ( Allg em ein e Mo dul e)/ Wich tig e Er lä uter ung en/Si ch erh eits- und s ons tig e Hi nw eise /Ac htu ng/Ac ht ung : D efek te oder bes chädi gt e G erät e austa usc hen! @ 6\mod_1260180857358_21.docx @ 46743 @ @ 1

Replace defective or damaged devices!

Replace defective or damaged device/module (e.g., in the event of deformed

contacts), since the long-term functionality of device/module involved can no

longer be ensured.

Pos: 15.1 1. 2 /Al le S eri en ( Allg em ein e Mo dul e)/ Wich tig e Er lä uter ung en/Si ch erh eits- und s ons tig e Hi nw eise /Ac htu ng/Ac ht ung : Ger äte vor kriec hen den und i sol ier end en S to ffen sch ütz en! @ 6\ mod_1260181036216_21.docx @ 46747 @ @ 1

Protect the components against materials having seeping and insulating

properties!

The components are not resistant to materials having seeping and insulating

properties such as: aerosols, silicones and triglycerides (found in some hand

creams). If you cannot exclude that such materials will appear in the component

environment, then install the components in an enclosure being resistant to the

above-mentioned materials. Clean tools and materials are imperative for handling

devices/modules.

Pos: 15.1 1. 3 /Al le S eri en ( Allg em ein e Mo dul e)/ Wich tig e Er lä uter ung en/Si ch erh eits- und sonstige Hinweise/Achtung/Achtung: Reinigung nur mit zulässig en M at eri alie n! @ 6\mod_1260181203293_21.docx @ 46751 @ @ 1

Clean only with permitted materials!

Clean soiled contacts using oil-free compressed air or with ethyl alcohol and

leather cloths.

Pos: 15.1 1. 4 /Al le S eri en ( Allg em ein e Mo dul e)/ Wich tig e Er lä uter ung en/Si ch erh eits- und sonstige Hinweise/Achtung/Achtung: Kein Kontaktspray verwenden! @ 6\mod_1260181290808_21.docx @ 46755 @ @ 1

12 Important Notes WAGO-I/O-SYSTEM 750

750-1606 Field Side Connection 16-

Manual

Version 1.1.0

Do not use any contact spray!

Do not use any contact spray. The spray may impair contact area functionality in

connection with contamination.

Pos: 15.1 1. 5 /Al le S eri en ( Allg em ein e Mo dul e)/ Wich tig e Er lä uter ung en/Si ch erh eits- und s ons tig e Hi nw eise /Ac htu ng/Ac ht ung : Ver pol ung ver mei den! @ 6\mod_1260184045744_21.docx @ 46767 @ @ 1

Do not reverse the polarity of connection lines!

Avoid reverse polarity of data and power supply lines, as this may damage the

devices involved.

Pos: 15.1 1. 6 /Al le S eri en ( Allg em ein e Mo dul e)/ Wich tig e Er lä uter ung en/Si ch erh eits- und sonstige Hinweise/Achtung/Achtung: Elektrostatische Entladung vermeiden! @ 6\mod_1260181364729_21.docx @ 46759 @ @ 1

Avoid electrostatic discharge!

The devices are equipped with electronic components that may be destroyed by

electrostatic discharge when touched. Please observe the safety precautions

against electrostatic discharge per DIN EN 61340-5-1/-3. When handling the

devices, please ensure that environmental factors (personnel, work space and

packaging) are properly grounded.

Pos: 16 /Doku ment ation all gemei n/Gli eder ungsel eme nte/---Seit en wechs el--- @ 3\mod_1221108045078_0.docx @ 21810 @ @ 1

WAGO-I/O-SYSTEM 750 Device Description 13

750-1606 Field Side Connection 16-

Manual

Version 1.1.0

Pos: 17 /A ll e Ser ien (Al lg emei ne M od ule)/ Üb ers chrif te n für al le S eri en/G erä teb esc hrei bu ng/G erä tebeschreibung - Übers chri ft 1 @ 3\mod_1233756084656_21.docx @ 27096 @ 1 @ 1

3 Device Description

Pos: 18.1 /Serie 750 (WAGO-I/O-SYST EM)/ Ger ätebesc hrei bung/Ei nlei tung /Anw endung /SY/A nwen dung 75 0-160 6 @ 8\mod_1278404447562_21.docx @ 59087 @ @ 1

The 750-1606 Field Side Connection Module provides 0 V to the outputs in

combination with the 16-channel 750-1504 Output Module (also suitable for 8-

channel output modules with a single conductor connection).

This does away with the need for additional rail-mounted terminal blocks.

Pos: 18.2 /Serie 750 (WAGO-I/O-SYST EM) /Ger äte besc hrei bu ng/Ei nlei tu ng/I/ O-B eschr ei bung/ SY/ I/O- Beschreibung 750-16 06 @ 8\ mod_1278405720936_21.docx @ 59091 @ @ 1

The 0 V power supply for the field level is provided to the Push-in CAGE

CLAMP

connectors 1 … 16.

Pos: 18.3 /Serie 750 (WAGO-I/O-SYST EM) /Ger äte besc hrei bu ng/Ei nlei tu ng/I/ O-B esc hrei bung /Al lg emei n/Ver wei s a uf K api tel "A nsc hlüss e" @ 8\ mod_1276775378035_21.docx @ 57956 @ @ 1

The assignment of the connections is described in the “Connectors” section.

Pos: 18.4 /Dokumentation allgemein/Gliederungselemente/------Leerzeil e------ @ 3\mod_1224662755687_0.docx @ 24460 @ @ 1

Pos: 18.5 /Serie 750 (WAGO-I/O-SYST EM) /Ger äte besc hrei bu ng/Ei nlei tu ng/V ers orgung /V ers orgung 24 V, 0 V über Leistungskontakte Standard @ 3\mod_1226498974531_21.docx @ 25020 @ @ 1

The I/O module 750-1606 (Field Side Connection 16-) receives the 24 V voltage

supply for the field level from an upstream I/O module or from the fieldbus

coupler/controller via blade-formed power jumper contacts. It then provides these

potentials to subsequent I/O modules via spring-formed power jumper contacts.

Pos: 18.6 /Serie 750 (WAGO-I/O-SYST EM)/ Wic htige Erl äuter unge n/Sic herhei ts- u nd sonsti ge Hin weis e/Ach tung/A chtu ng: Ma ximaler Strom L eistung skon takt e 10 A @ 3\mod_1226499143500_21.docx @ 25029 @ @ 1

Do not exceed maximum current via power jumper contacts!

The maximum current to flow through the power jumper contacts is 10 A.

Greater currents can damage the contacts.

When configuring your system, ensure that this current is not exceeded. If

exceeded, insert an additional supply module.

Pos: 18.7 /Serie 750 (WAGO-I/O-SYST EM )/ Ger äteb esc hrei bung /Ei nlei tu ng/Ei ns atz ber eich /Ei nsatz ber eic h 7 50- xxxx all e Koppl er/C ontr oller oh ne Einsc hrän kung @ 3\mod_1232541691906_21.docx @ 26522 @ @ 1

The I/O module 750-1606 can be used with all fieldbus couplers/controllers of the

WAGO-I/O-SYSTEM 750.

Pos: 19 /Doku ment ation all gemei n/Gli eder ungsel eme nte/---Seit en wechs el--- @ 3\mod_1221108045078_0.docx @ 21810 @ @ 1

14 Device Description WAGO-I/O-SYSTEM 750

750-1606 Field Side Connection 16-

Manual

Version 1.1.0

Pos: 20 /A ll e Ser ien (Al lg emei ne M od ule)/ Üb ers chrif te n für al le S eri en/G erä teb esc hrei bu ng/A nsic ht - Ü b erschr if t 2 @ 4\ mod_1240984217343_21.docx @ 31958 @ 2 @ 1

3.1 View

Pos: 21 /S eri e 7 50 ( WA GO-I/ O-SYST EM) /Ger ät ebesc hrei bu ng/A nsic ht/S yste mkl em men/A nsich t 750-1605, -1606, -1607 @ 8\mod_1277893772696_21.docx @ 58669 @ @ 1

Figure 1: View

Pos: 22 /S eri e 7 50 ( WA GO-I/O-S YSTEM )/Ger äteb eschr eibung /Ansi cht /Ansic ht Push- in C ag eCla mp® _Leg end e o hne LED s @ 15\ mod_1370852761670_21.docx @ 122217 @ @ 1

Table 3: Legend for Figure “View”

Pos.

Description

Details See Section

Marking possibility with

Mini-WSB

---

Data contacts

“Device Description” > “Connectors”

Push-in CAGE CLAMP

connectors

“Device Description” > “Connectors”

Power jumper contacts

“Device Description” > “Connectors”

Release tab

“Mounting” > “Inserting and Removing

Devices”

Pos: 23 /Doku ment ation all gemei n/Gli eder ungsel eme nte/---Seit en wechs el--- @ 3\mod_1221108045078_0.docx @ 21810 @ @ 1

WAGO-I/O-SYSTEM 750 Device Description 15

750-1606 Field Side Connection 16-

Manual

Version 1.1.0

Pos: 24 /A ll e Ser ien (Al lg emei ne M od ule)/ Üb ers chrif te n für al le S eri en/G erä teb esc hrei bu ng/A nsc hlüs se - Über schri ft 2 @ 4\mod_1240984262656_21.docx @ 31961 @ 2 @ 1

3.2 Connectors

Pos: 25 /S eri e 7 50 ( WA GO-I/ O-SYST EM) /Ger ät ebesc hrei bu ng/A nsc hlüss e/D ate nko ntakt e/Kl em menbu s - Ü bersc hrift 3 @ 6\mod_1256294684083_21.docx @ 43660 @ 3 @ 1

3.2.1 Data Contacts/Internal Bus

Pos: 26.1 /Serie 750 (WAGO-I/O-SYSTEM) /Ger äte besc hrei bu ng/A nsc hlüss e/D ate nkon takt e - F eldbu sko ppler /-c ontr oll er, A bbi ld ung und Besc hrei bu ng @ 3\mod_1231771259187_21.docx @ 26002 @ @ 1

Communication between the fieldbus coupler/controller and the I/O modules as

well as the system supply of the I/O modules is carried out via the internal bus. It

is comprised of 6 data contacts, which are available as self-cleaning gold spring

contacts.

Figure 2: Data Contacts

Pos: 26.2 /Serie 750 (WAGO-I/O-SYST EM)/ Wic htige Erl äuter unge n/Sic herhei ts- u nd so nsti g e Hin weis e/ Acht ung /Ach tu ng: Buskl e mmen nic ht auf Gol dfe der konta kt e leg en! @ 7 \mod_1266318463636_21.docx @ 50695 @ @ 1

Do not place the I/O modules on the gold spring contacts!

Do not place the I/O modules on the gold spring contacts in order to avoid soiling

or scratching!

Pos: 26.3 /Serie 750 (WAGO-I/O-SYST EM)/ Wic htige Erl äuter unge n/Sic herhei ts- und sonstige Hinweise/Achtung/Achtung: ESD - Auf g ute Erd ung der U mg ebu ng ac ht en! @ 7\ mod_1266318538667_21.docx @ 50708 @ @ 1

Ensure that the environment is well grounded!

The devices are equipped with electronic components that may be destroyed by

electrostatic discharge. When handling the devices, ensure that the environment

(persons, workplace and packing) is well grounded. Avoid touching conductive

components, e.g. data contacts.

Pos: 27 /Doku ment ation all gemei n/Gli eder ungsel eme nte/---Seit en wechs el--- @ 3\mod_1221108045078_0.docx @ 21810 @ @ 1

16 Device Description WAGO-I/O-SYSTEM 750

750-1606 Field Side Connection 16-

Manual

Version 1.1.0

Pos: 28 /S eri e 7 50 ( WA GO-I/ O-SYST EM) /Ger ät ebesc hrei bu ng/A nsc hlüss e/L eist ung skont akt e/F eld vers orgung - Über schri ft 3 @ 6\mod_1256294692864_21.docx @ 43664 @ 3 @ 1

3.2.2 Power Jumper Contacts/Field Supply

Pos: 29.1 /Serie 750 (WAGO-I/O-SYST EM)/ Wic htige Erl äuter unge n/Sic herhei ts- u nd so nsti g e Hin weis e/ Vorsi cht /V orsi cht : Ver let zung sge fa hr dur c h sc harf kan tig e M ess erko nta kte! @ 6\ mod_1256193279401_21.docx @ 43414 @ @ 1

Risk of injury due to sharp-edged blade contacts!

The blade contacts are sharp-edged. Handle the I/O module carefully to prevent

injury.

Pos: 29.2 /Serie 750 (WAGO-I/O-SYST EM )/ Ger äteb esc hrei bung /Ans chl üs se/L eist u ngs kont akte 2 LK (M ess er/ Leis tung s konta kte 2 L K (M ess er/ Fed er) - Ei nleitung @ 15\mod_1371721641099_21.docx @ 123714 @ @ 1

The I/O module 750-1606 has 2 self-cleaning power jumper contacts that supply

and transmit power for the field side. The contacts on the left side of the I/O

module are designed as blade contacts and those on the right side as spring

contacts.

Pos: 29.3 /Serie 750 (WAGO-I/O-SYST EM)/ Ger ätebesc hrei bung/A nschl üsse /Leist ung skont akte 2 LK (M esser /Feder ) - Abbildung (16-Kanal) @ 1 5\mod_1370866610582_21.docx @ 122222 @ @ 1

Figure 3: Power Jumper Contacts

Pos: 29.4 /Serie 750 (WAGO-I/O-SYST EM )/ Ger äteb esc hrei bung /Ans chl üs se/L eist u ngs kont akte 2 LK (M ess er/ Leis tung s konta kte 2 L K (Messer/Feder) - Legend e @ 15\mod_1371721352500_21.docx @ 123710 @ @ 1

Table 4: Legend for Figure “Power Jumper Contacts”

Contact

Type

Function

Spring contact

Potential transmission (U

) for field supply

Spring contact

Potential transmission (0 V) for field supply

Blade contact

Potential feed-in (0 V) for field supply

Blade contact

Potential feed-in (U

) for field supply

Pos: 29.5 /Serie 750 (WAGO-I/O-SYST EM)/ Wic htige Erl äuter unge n/Sic herhei ts- u nd so nsti g e Hin weis e/ Acht ung /Acht ung: M aximal er Stro m Leist ungs kontak te 10 A @ 3\mod_1226499143500_21.docx @ 25029 @ @ 1

Do not exceed maximum current via power jumper contacts!

The maximum current to flow through the power jumper contacts is 10 A.

Greater currents can damage the contacts.

When configuring your system, ensure that this current is not exceeded. If

exceeded, insert an additional supply module.

Pos: 29.6 /Serie 750 (WAGO-I/O-SYST EM)/ Wic htige Erl äuter unge n/Sic herhei ts- u nd so nsti g e Hin weis e/H inw eis/H i nwei s: Pote nti alei ns peis ekl emme für Erd e ei nse tze n! ( kei ne L K f ür E rde) @ 3 \mod_1226499037468_21.docx @ 25023 @ @ 1

WAGO-I/O-SYSTEM 750 Device Description 17

750-1606 Field Side Connection 16-

Manual

Version 1.1.0

Use supply modules for ground (earth)!

The I/O module has no power jumper contacts for receiving and transmitting the

earth potential. Use a supply module when an earth potential is needed for the

subsequent I/O modules.

Pos: 30 /Doku ment ation all gemei n/Gli eder ungsel eme nte/---Seit en wechs el--- @ 3\mod_1221108045078_0.docx @ 21810 @ @ 1

18 Device Description WAGO-I/O-SYSTEM 750

750-1606 Field Side Connection 16-

Manual

Version 1.1.0

Pos: 31 /S eri e 7 50 ( WA GO-I/ O-SYST EM) /Ger ät ebesc hrei bu ng/A nsc hlüss e/P ush- in CAG E C LAM P®-Ans chl üss e - Ü bersc hri ft 3 @ 15\mod_1370519905692_21.docx @ 122018 @ 3 @ 1

3.2.3 Push-in CAGE CLAMP

Connectors

Pos: 32 /S eri e 7 50 ( WA GO-I/ O-SYST EM) /G erät eb esc hrei bung /Ans chl üss e/S yst em klem men /Ans chl üss e 7 50-1 606 far bneutr al @ 15\ mod_1369811152521_21.docx @ 121077 @ @ 1

Figure 4: Push-in CAGE CLAMP

Connectors

Table 5: Legend for Figure “Push-in CAGE CLAMP

Connectors”

Designation

Connector

Function

DC 0 V

Output 0 V

DC 0 V

Output 0 V

DC 0 V

Output 0 V

DC 0 V

Output 0 V

Pos: 33 /Doku ment ation all gemei n/Gli eder ungsel eme nte/---Seit en wechs el--- @ 3\mod_1221108045078_0.docx @ 21810 @ @ 1

Pos: 34 /A ll e Ser ien (Al lg emei ne M od ule)/ Üb ers chrif te n für al le S eri en/G erä teb esc hrei bu ng/A nzei geel em ente - Üb erschr ift 2 @ 4\mod_1240984390875_21.docx @ 31964 @ 2 @ 1

3.3 Display Elements

Pos: 35 /S eri e 7 50 ( WA GO-I/ O-SYST EM)/ Gerät ebesc hrei bung/A nzei geele mente /Anz eigeel ement e 750- xxxx nicht vorhanden @ 4\mod_1236321917062_21.docx @ 28060 @ @ 1

The I/O module 750-1606 has no display elements.

Pos: 36 /A ll e Ser ien (Al lg emei ne M od ule)/ Üb ers chrif te n für al le S eri en/G erä teb esc hrei bu ng/B edi enel eme nte - Üb ersc hrif t 2 @ 4 \mod_1239191655456_21.docx @ 30439 @ 2 @ 1

3.4 Operating Elements

Pos: 37 /S eri e 7 50 ( WA GO-I/ O-SYST EM) /G erät eb esc hrei bung /Be die nel em ente/ Bedi en elem ent e B uskl em me 7 50- xxxx nicht vor hande n @ 4\mod_1236322031125_21.docx @ 28063 @ @ 1

The I/O module 750-1606 has no operating elements.

Pos: 38 /D oku ment atio n al lg emei n/G lie der ungs ele me nte/---Sei te nwec hsel --- @ 3\mod_1221108045078_0.docx @ 21810 @ @ 1

WAGO-I/O-SYSTEM 750 Device Description 19

750-1606 Field Side Connection 16-

Manual

Version 1.1.0

Pos: 39 /A ll e Ser ien (Al lg emei ne M od ule)/ Üb ers chrif te n für al le S eri en/G erä teb esc hrei bu ng/Sc he mati sch es S ch altbi ld - Über schr ift 2 @ 4\mod_1240984441312_21.docx @ 31967 @ 2 @ 1

3.5 Schematic Diagram

Pos: 40 /S eri e 7 50 ( WA GO-I/ O-SYST EM) /G erät eb esc hrei bung /Sc he mati sche Sc hal tbil der/ Sys tem kle mme n/Sc he matis ch es Schal tbi ld 75 0-160 6 @ 8\mod_1278409773623_21.docx @ 59113 @ @ 1

Figure 5: Schematic Diagram

Pos: 41 /Doku ment ation all gemei n/Gli eder ungsel eme nte/---Seit en wechs el--- @ 3\mod_1221108045078_0.docx @ 21810 @ @ 1

20 Device Description WAGO-I/O-SYSTEM 750

750-1606 Field Side Connection 16-

Manual

Version 1.1.0

Pos: 42 /A ll e Ser ien (Al lg emei ne M od ule)/ Üb ers chrif te n für al le S eri en/G erä teb esc hrei bu ng/Te ch nisc he D ate n - Ü ber schr ift 2 @ 3\ mod_1232967587687_21.docx @ 26924 @ 2 @ 1

3.6 Technical Data

Pos: 43 /S eri e 7 50 ( WA GO-I/ O-SYST EM) /Ger ät ebesc hrei bu ng/T ech nische Daten/Systemklemmen/Technische Daten 750-1606 @ 8\mod_1278411586738_21.docx @ 59126 @ 33 @ 1

3.6.1 Device

Table 6: Technical Data – Device

Width

12 mm

Height (from upper edge of 35 DIN rail)

64 mm

Depth

100 mm

Weight

45 g

3.6.2 Supply

Table 7: Technical Data – Supply

Voltage supply

Via power jumper contacts 24 VDC

Voltage via power jumper contacts

24 VDC

Current via power jumper contacts

max.

10 A

Potential connections

16 × 0 V

Pos: 44.1 /All e Seri en ( All ge meine Mo dul e)/Ü berschr ifte n für alle S erie n/Gerä tebes chrei bung /Ansc hluss techni k - Über schr if t 3 @ 17\ mod_1380123271324_21.docx @ 132788 @ 3 @ 1

3.6.3 Connection Type

Pos: 44.2 /Serie 750 (WAGO-I/O-SYST EM )/ Ger äteb esc hrei bung /T echni sc he D ate n/A nsc hluss tec hni k/T ec hnisc he D at en V erdr ah tung sebe ne Pus h-in CC - 0,08 bis 1,5 mm 2(ei ndrg .) + 0, 25 bi s 1 ,5m m2( fei ndrg .) @ 1 9\mod_1400241224524_21.docx @ 153913 @ @ 1

Table 8: Technical Data ‒ Field Wiring

Wire connection

Push-in CAGE CLAMP

Cross section, solid wire

0.08 mm² … 1.5 mm² / AWG 28 … 16

Cross section, fine-stranded wire

0.25 mm² … 1.5 mm² / AWG 22 … 16

Stripped lengths

8 mm … 9 mm / 0.33 in

Pos: 44.3 /Serie 750 (WAGO-I/O-SYST EM )/ Ger äteb esc hrei bung /T echni sc he D ate n/A nsc hluss tec hni k/T ec hnisc he D at en L eistungskontakte (Messer/Feder) ohne Spannungsabfall @ 19\mod_1400241643293_21.docx @ 153921 @ @ 1

Table 9: Technical Data – Power Jumper Contacts

Power jumper contacts

Blade/spring contact, self-cleaning

Pos: 44.4 /Serie 750 (WAGO-I/O-SYST EM )/ Ger äteb esc hrei bung /T echni sc he D ate n/A nsc hluss tec hni k/T ec hnisc he D at en D ate nkon ta kte @ 1 7\mod_1380123495844_21.docx @ 132794 @ @ 1

Table 10: Technical Data – Data Contacts

Data contacts

Slide contact, hard gold plated, self-

cleaning

Pos: 45 /S eri e 7 50 ( WA GO-I/ O-SYST EM) /G erät eb esc hrei bung /T echni sc he D ate n/Kl ima tis che U mw elt bedi ng ung en/Te ch nisc he Date n K lim at. U m weltb ed. ohn e er w. T e mp. 0. ..5 5°C /-25.. .+85° C @ 5\mod_1247657968368_21.docx @ 37603 @ 3 @ 1

Page is loading ...

WAGO Field side connection module 16- User manual

WAGO Field side connection module 16- User manual

WAGO Field side connection module 16- User manual

Related papers

Other documents