WAGO 2-channel solid-state load relay User manual

Pos: 2 /Dokumentation allgemein/Einband/Einband Handbuch - Deckbl at t oh ne V aria nt enfel d (S ta ndar d) @ 9 \mod_1285229289866_0.docx @ 64941 @ @ 1

Manual

WAGO-I/O-SYSTEM 750

2DO 230V AC 0.3A/SSR

753-509

2-

Channel Digital Output Module 230 V AC/DC,

with solid state relay 0.3 A

Version 1.1.0

Pos: 3 /A lle Ser ien ( All ge mein e M odul e)/ Hin weis e z ur D oku men tati on/I mpr ess um für Sta ndar dh and büch er - al lg. A ngabe n, Ansc hrifte n, Telef onn ummer n und E-Mai l-A dresse n @ 3\mod_1219151118203_21.docx @ 21060 @ @ 1

2 WAGO-I/O-SYSTEM 750

753-509 2DO 230V AC 0.3A/SSR

Manual

Version 1.1.0

WAGO Kontakttechnik GmbH & Co. KG

Hansastraße 27

D-32423 Minden

Phone: +49 (0) 571/8 87 – 0

Fax: +49 (0) 571/8 87 – 1 69

E-Mail: [email protected]

Web: http://www.wago.com

Technical Support

Phone: +49 (0) 571/8 87 – 5 55

Fax: +49 (0) 571/8 87 – 85 55

E-Mail: [email protected]

Every conceivable measure has been taken to ensure the accuracy and

completeness of this documentation. However, as errors can never be fully

excluded, we always appreciate any information or suggestions for improving the

documentation.

E-Mail: [email protected]

We wish to point out that the software and hardware terms as well as the

trademarks of companies used and/or mentioned in the present manual are

generally protected by trademark or patent.

=== Ende der Lis te f ür T e xtmar ke Ei nb and _vor ne = ==

WAGO-I/O-SYSTEM 750 Table of Contents 3

753-509 2DO 230V AC 0.3A/SSR

Manual

Version 1.1.0

Pos: 5 /D ok ument ati on al lg em ein/V erz eic hni sse /Inh alts ver zei chni s - Ü bersc hrift oG und Ver zeich nis @ 3\mod_1219151230875_21.docx @ 21063 @ @ 1

Table of Contents

1 Notes about this Documentation ................................................................. 5

1.1 Validity of this Documentation ................................................................. 5

1.2 Copyright ................................................................................................... 5

1.3 Symbols ..................................................................................................... 6

1.4 Number Notation ....................................................................................... 8

1.5 Font Conventions ...................................................................................... 8

2 Important Notes ........................................................................................... 9

2.1 Legal Bases ............................................................................................... 9

2.1.1 Subject to Changes ............................................................................... 9

2.1.2 Personnel Qualifications ....................................................................... 9

2.1.3 Use of the WAGO-I/O-SYSTEM 750 in Compliance with

Underlying Provisions .......................................................................... 9

2.1.4 Technical Condition of Specified Devices ......................................... 10

2.2 Safety Advice (Precautions) .................................................................... 11

3 Device Description ..................................................................................... 13

3.1 View ........................................................................................................ 14

3.2 Connectors ............................................................................................... 15

3.2.1 Data Contacts/Internal Bus ................................................................. 15

3.2.2 Power Jumper Contacts/Field Supply ................................................ 16

3.2.3 CAGE CLAMP

®

Connectors ............................................................. 18

3.3 Display Elements .................................................................................... 19

3.4 Schematic Diagram ................................................................................. 20

3.5 Technical Data ........................................................................................ 21

3.5.1 Device ................................................................................................. 21

3.5.2 Power Supply...................................................................................... 21

3.5.3 Communication .................................................................................. 21

3.5.4 Outputs ............................................................................................... 21

3.5.5 Connection .......................................................................................... 22

3.5.6 Climatic Environmental Conditions ................................................... 22

3.6 Approvals ................................................................................................ 23

3.7 Standards and Guidelines ........................................................................ 25

4 Process Image ............................................................................................. 26

5 Mounting ..................................................................................................... 27

5.1 Mounting Sequence ................................................................................. 27

5.2 Inserting and Removing Devices ............................................................ 28

5.2.1 Inserting the I/O Module .................................................................... 28

5.2.2 Removing the I/O Module .................................................................. 29

5.3 I/O Modules with Pluggable Wiring Level (Series 753) ........................ 30

5.3.1 Coding ................................................................................................ 31

5.3.2 Connector Removal ............................................................................ 33

6 Connect Devices ......................................................................................... 34

6.1 Connecting a Conductor to the CAGE CLAMP

®

................................... 34

6.2 Connection Examples .............................................................................. 36

6.2.1 2-Wire Connection, Protection Class I Actuators .............................. 36

4 Table of Contents WAGO-I/O-SYSTEM 750

753-509 2DO 230V AC 0.3A/SSR

Manual

Version 1.1.0

6.2.2 2-Wire Connection, Protection Class II Actuators ............................. 36

6.2.3 3-Wire Connection, Protection Class I Actuators .............................. 37

6.2.4 3-Wire Connection, Protection Class II Actuators ............................. 37

6.3 Protective Circuits for Contacts of Relay Modules ................................. 38

7 Use in Hazardous Environments .............................................................. 40

7.1 Marking Configuration Examples ........................................................... 41

7.1.1 Marking for Europe According to ATEX and IEC-Ex ...................... 41

7.1.2 Marking for America According to NEC 500 .................................... 46

7.2 Installation Regulations ........................................................................... 47

7.2.1 Special Conditions for Safe Use

(ATEX Certificate TÜV 07 ATEX 554086 X) .................................. 48

7.2.2 Special Conditions for Safe Use

(ATEX Certificate TÜV 12 ATEX 106032 X) .................................. 49

7.2.3 Special Conditions for Safe Use

(IEC-Ex Certificate TUN 09.0001 X) ................................................ 50

7.2.4 Special Conditions for Safe Use

(IEC-Ex Certificate IECEx TUN 12.0039 X) .................................... 51

7.2.5 Special Conditions for Safe Use According to ANSI/ISA 12.12.01 .. 52

List of Figures ...................................................................................................... 53

List of Tables ........................................................................................................ 54

=== Ende der Lis te f ür T e xtmar ke V erz eic hnis _vor ne == =

WAGO-I/O-SYSTEM 750 Notes about this Documentation 5

753-509 2DO 230V AC 0.3A/SSR

Manual

Version 1.1.0

Pos: 7 /A lle Ser ien ( All ge mein e M odul e)/ Über sc hrif ten für all e Ser ie n/Hi nwei se zur D o kume nt ation /Hi nw eise zu dies er D o kume ntati on - Ü b ersc hrif t 1 @ 4 \mod_1237987661750_21.docx @ 29029 @ 1 @ 1

1 Notes about this Documentation

Pos: 8 /A lle Ser ien ( All ge mein e M odul e)/ Hin weis e z ur D oku men tati on/H i nweis e/Hi n weis : D okum ent atio n a ufbe wahr e n @ 4 \mod_1237987339812_21.docx @ 29026 @ @ 1

Always retain this documentation!

This documentation is part of the product. Therefore, retain the documentation

during the entire service life of the product. Pass on the documentation to any

subsequent user. In addition, ensure that any supplement to this documentation is

included, if necessary.

Pos: 9 /A lle Ser ien ( All ge mein e M odul e)/ Über sc hrif ten für all e Ser ie n/Hi nwei se zur D o kume nt ation /G ültig kei tsb erei ch - Ü b ersc hrif t 2 @ 1 2\mod_1338912448776_21.docx @ 96469 @ 2 @ 1

1.1 Validity of this Documentation

Pos: 10 /S eri e 7 50 ( WA GO-I/ O-SYST EM) /Hi n weis e zur D okum ent ati on/G ülti gkei ts berei c h/Gül tig kei tsber ei ch D oku men tat ion Bus kle mme 75 0-xx xx, nur St andar dvers ion @ 14\mod_1358944037400_21.docx @ 109342 @ @ 1

This documentation is only applicable to the I/O module 753-509

(2DO 230V AC 0.3A/SSR).

Pos: 11 /S eri e 7 50 ( WA GO-I/ O-SYST EM) /Hi n weis e zur D okum ent ati on/Hi nw eise /Ac htu ng: H in weis zur D oku ment ati on B uskl emmen 750-xxxx @ 4\mod_1237986979656_21.docx @ 29023 @ @ 1

The I/O module 753-509 shall only be installed and operated according to the

instructions in this manual and in the manual for the used fieldbus

coupler/controller.

Consider power layout of the WAGO-I/O-SYSTEM 750!

In addition to these operating instructions, you will also need the manual for the

used fieldbus coupler/controller, which can be downloaded at www.wago.com.

There, you can obtain important information including information on electrical

isolation, system power and supply specifications.

Pos: 12.1 /All e Seri en ( All ge meine Mo dul e)/H in weis e zur D oku ment ati on/U rh eber sc hutz aus führ lic h @ 4\mod_1235565145234_21.docx @ 27691 @ 2 @ 1

1.2 Copyright

This Manual, including all figures and illustrations, is copyright-protected. Any

further use of this Manual by third parties that violate pertinent copyright

provisions is prohibited. Reproduction, translation, electronic and phototechnical

filing/archiving (e.g., photocopying) as well as any amendments require the

written consent of WAGO Kontakttechnik GmbH & Co. KG, Minden, Germany.

Non-observance will involve the right to assert damage claims.

Pos: 12.2 /Dokumentation allgemein/Gliederungs ele mente /---Seit en wechs el--- @ 3\mod_1221108045078_0.docx @ 21810 @ @ 1

6 Notes about this Documentation WAGO-I/O-SYSTEM 750

753-509 2DO 230V AC 0.3A/SSR

Manual

Version 1.1.0

Pos: 12.3 /All e Seri en ( All ge meine Mo dul e)/Ü bers chr ift en f ür alle S erie n/Hi nwei se z ur Dok um enta tio n/S ymbol e - Ü bers chr ift 2 @ 1 3\mod_1351068042408_21.docx @ 105270 @ 2 @ 1

1.3 Symbols

Pos: 12 .4.1 /Al le Seri en (All gemei ne Mod ule)/ Wichti ge Erl äuter unge n/Sich erheit s- und sonstige Hinweise/Gefahr/Gefahr: _Warnung vor Personenschäden allgemein_ - Erläuter ung @ 13 \mod_1343309450020_21.docx @ 101029 @ @ 1

Personal Injury!

Indicates a high-risk, imminently hazardous situation which, if not avoided, will

result in death or serious injury.

Pos: 12 .4.2 /Al le Seri en (All gemei ne Mod ule)/ Wichti ge Erl äuter unge n/Sich erheit s- und sonsti ge Hinw eise/ Gefa hr/Gef ahr: _ Warnu ng vor Per son enschä den durc h elek trisc hen Str om_ - Erläuterung @ 13\mod_1343309694914_21.docx @ 101030 @ @ 1

Personal Injury Caused by Electric Current!

Indicates a high-risk, imminently hazardous situation which, if not avoided, will

result in death or serious injury.

Pos: 12 .4.3 /Al le Seri en (All gemei ne Mod ule)/ Wichti ge Erl äuter unge n/Sich erheit s- und sonstige Hinweis e/W arn ung/ Warn ung: _ Warn ung vor P erso nensc h äde n allg em ei n_ - Erläuterung @ 13\mod_1343309877041_21.docx @ 101035 @ @ 1

Personal Injury!

Indicates a moderate-risk, potentially hazardous situation which, if not avoided,

could result in death or serious injury.

Pos: 12 .4.4 /Al le Seri en (All gemei ne Mod ule)/ Wichti ge Erl äuter unge n/Sich erheit s- und so nsti ge H inw eis e/V orsic ht /Vor sich t: _War nung vor Person ensc häden al lge mein_ - Erläuterung @ 13\mod_1343310028762_21.docx @ 101038 @ @ 1

Personal Injury!

Indicates a low-risk, potentially hazardous situation which, if not avoided, may

result in minor or moderate injury.

Pos: 12 .4.5 /Al le Seri en (All gemei ne Mod ule)/ Wichti ge Erl äuter unge n/Sich erheit s- und sonstige Hinweise/Achtung/Achtung: _Warnung vor Sachs chä den all ge mein _ - Erläuterung @ 13\mod_1343310134623_21.docx @ 101041 @ @ 1

Damage to Property!

Indicates a potentially hazardous situation which, if not avoided, may result in

damage to property.

Pos: 12 .4.6 /Al le Seri en (All gemei ne Mod ule)/ Wichti ge Erl äuter unge n/Sich erheit s- und sonstige Hinweise/Achtung/Achtung: _Warnung vor Sachschäden durch elektrostatische Aufladung_ - Erläuterung @ 13\mod_1343310227702_21.docx @ 101044 @ @ 1

Damage to Property Caused by Electrostatic Discharge (ESD)!

Indicates a potentially hazardous situation which, if not avoided, may result in

damage to property.

Pos: 12 .4.7 /Al le Seri en (All ge mei ne Mo dul e)/ Wic htig e Er lä uter ung en/ Sich erh eits- und sonstige Hinweise/Hinweis/Hinweis: _Wichtiger Hinweis allgemein_ - Erläuterung @ 13\mod_1343310326906_21.docx @ 101047 @ @ 1

Important Note!

Indicates a potential malfunction which, if not avoided, however, will not result in

damage to property.

Pos: 12 .4.8 /Al le Seri en (All gemei ne Mod ule)/ Wichti ge Erl äuter unge n/Sich erheit s- und so nsti ge H inw eis e/I nfor mat ion/ Inf or matio n: _W eiter e Inf or mati on allg emei n_ - Erl äuter ung @ 13 \mod_1343310439814_21.docx @ 101051 @ @ 1

WAGO-I/O-SYSTEM 750 Notes about this Documentation 7

753-509 2DO 230V AC 0.3A/SSR

Manual

Version 1.1.0

Additional Information:

Refers to additional information which is not an integral part of this

documentation (e.g., the Internet).

Pos: 12.5 /Dokumentation allgemein/Gliederungselemente/---Seite nwechs el--- @ 3\ mod_1221108045078_0.docx @ 21810 @ @ 1

8 Notes about this Documentation WAGO-I/O-SYSTEM 750

753-509 2DO 230V AC 0.3A/SSR

Manual

Version 1.1.0

Pos: 12 .6 /All e Seri en (Allg emeine Modul e)/Hi nweis e zur Do kument ation /Zahl ensy steme @ 3\ mod_1221059454015_21.docx @ 21711 @ 2 @ 1

1.4 Number Notation

Table 1: Number Notation

Number Code

Example

Note

Decimal

100

Normal notation

Hexadecimal

0x64

C notation

Binary

'100'

'0110.0100'

In quotation marks, nibble separated with

dots (.)

Pos: 12.7 /All e Seri en ( All ge meine Mo dule) /Hin weise zur Doku mentat ion/S chrif tkon venti onen @ 3\ mod_1221059521437_21.docx @ 21714 @ 2 @ 1

1.5 Font Conventions

Table 2: Font Conventions

Font Type

Indicates

italic

Names of paths and data files are marked in italic-type.

e.g.: C:\Program Files\WAGO Software

Menu

Menu items are marked in bold letters.

e.g.: Save

>

A greater-than sign between two names means the selection of a

menu item from a menu.

e.g.: File > New

Input

Designation of input or optional fields are marked in bold letters,

e.g.: Start of measurement range

“Value”

Input or selective values are marked in inverted commas.

e.g.: Enter the value “4 mA” under Start of measurement range.

[Button]

Pushbuttons in dialog boxes are marked with bold letters in square

brackets.

e.g.: [Input]

[Key]

Keys are marked with bold letters in square brackets.

e.g.: [F5]

Pos: 13 /Doku ment ation all gemei n/Gli eder ungsel eme nte/---Seit en wechs el--- @ 3\mod_1221108045078 _0. doc x @ 2 181 0 @ @ 1

WAGO-I/O-SYSTEM 750 Important Notes 9

753-509 2DO 230V AC 0.3A/SSR

Manual

Version 1.1.0

Pos: 14 /Alle Ser ien (Al lge meine Mo dule)/ Über schrif ten für alle Ser ien/ Wichti ge Erlä uteru ngen/ Wich tige Er läuter ungen - Übersc hrift 1 @ 4\mod_1241428899156_21.docx @ 32170 @ 1 @ 1

2 Important Notes

Pos: 15 .1 /All e Seri en (Allgemeine Dokumente) (Allgemeine Module)/Wichtige Erläuterungen/Wichtige Erläuterungen - Einl eitung @ 3\mod_1221059818031_21.docx @ 21717 @ @ 1

This section includes an overall summary of the most important safety

requirements and notes that are mentioned in each individual section. To protect

your health and prevent damage to devices as well, it is imperative to read and

carefully follow the safety guidelines.

Pos: 15 .2 /All e Seri en (Allg emeine Modul e)/Ü berschr ifte n für alle S erie n/Wich tige Er läuter ung enRec htlic he Gr undl ag en - Üb ersc hrift 2 @ 3\ mod_1221060626343_21.docx @ 21726 @ 2 @ 1

2.1 Legal Bases

Pos: 15.3 /Alle Serien (Allgemeine Dokumente) (Allgemeine Module)/Wichtige Erläuterungen/Änderungsvorbehalt - Übers chri ft 3 un d I nhalt @ 3\mod_1221060036484_21.docx @ 21720 @ 3 @ 1

2.1.1 Subject to Changes

WAGO Kontakttechnik GmbH & Co. KG reserves the right to provide for any

alterations or modifications that serve to increase the efficiency of technical

progress. WAGO Kontakttechnik GmbH & Co. KG owns all rights arising from

the granting of patents or from the legal protection of utility patents. Third-party

products are always mentioned without any reference to patent rights. Thus, the

existence of such rights cannot be excluded.

Pos: 15.4 /Serie 750 (WAGO-I/O-SYSTEM) /Wic htige Er läut erung en/Per sonal qual ifika tionP erson alqu alifi kation 75 0-xxxx - Ü bersc hrift 3 u nd Inhal t @ 3\mod_1224061208046_21.docx @ 24063 @ 3 @ 1

2.1.2 Personnel Qualifications

All sequences implemented on WAGO-I/O-SYSTEM 750 devices may only be

carried out by electrical specialists with sufficient knowledge in automation. The

specialists must be familiar with the current norms and guidelines for the devices

and automated environments.

All changes to the coupler or controller should always be carried out by qualified

personnel with sufficient skills in PLC programming.

Pos: 15.5 /Serie 750 (WAGO-I/O-SYSTEM)/Wichtige Erläuterungen/Bestimmungsgemäße VerwendungBestimmungsgemäße Verwendung 750-xxxx - Über schri ft 3 un d I nhal t @ 3\ mod_1224064151234_21.docx @ 24070 @ 3 @ 1

2.1.3 Use of the WAGO-I/O-SYSTEM 750 in Compliance with

Underlying Provisions

Fieldbus couplers, fieldbus controllers and I/O modules found in the modular

WAGO-I/O-SYSTEM 750 receive digital and analog signals from sensors and

transmit them to actuators or higher-level control systems. Using programmable

controllers, the signals can also be (pre-) processed.

The devices have been developed for use in an environment that meets the IP20

protection class criteria. Protection against finger injury and solid impurities up to

12.5 mm diameter is assured; protection against water damage is not ensured.

Unless otherwise specified, operation of the devices in wet and dusty

environments is prohibited.

Operating the WAGO-I/O-SYSTEM 750 devices in home applications without

further measures is only permitted if they meet the emission limits (emissions of

interference) according to EN 61000-6-3. You will find the relevant information

in the section “Device Description” > “Standards and Guidelines” in the manual

for the used fieldbus coupler/controller.

10 Important Notes WAGO-I/O-SYSTEM 750

753-509 2DO 230V AC 0.3A/SSR

Manual

Version 1.1.0

Appropriate housing (per 94/9/EG) is required when operating the WAGO-I/O-

SYSTEM 750 in hazardous environments. Please note that a prototype test

certificate must be obtained that confirms the correct installation of the system in

a housing or switch cabinet.

Pos: 15.6 /All e Seri en ( All ge meine Do kum ente) ( All ge meine Mo dule) /Wi cht ige Erl äut eru nge n/T echni sc her Zus tan d d er G erä te - Ü bersc hrift 3 un d Inhal t @ 3\mod_1221060446109_21.docx @ 21723 @ 3 @ 1

2.1.4 Technical Condition of Specified Devices

The devices to be supplied ex works are equipped with hardware and software

configurations, which meet the individual application requirements. WAGO

Kontakttechnik GmbH & Co. KG will be exempted from any liability in case of

changes in hardware or software as well as to non-compliant usage of devices.

Please send your request for modified and new hardware or software

configurations directly to WAGO Kontakttechnik GmbH & Co. KG.

Pos: 15.7 /Dokumentation all ge mein/ Glie der ungs ele mente /---Seit en wechs el--- @ 3\mod_1221108045078_0.docx @ 21810 @ @ 1

WAGO-I/O-SYSTEM 750 Important Notes 11

753-509 2DO 230V AC 0.3A/SSR

Manual

Version 1.1.0

Pos: 15 .8 /All e Seri en (Allg emeine Modul e)/Ü berschr ifte n für alle S erie n/Wich tige Er läuter ung enSic herhei tshi nweis e - Übers chrif t 2 @ 6\mod_1260180299987_21.docx @ 4672 4 @ 2 @ 1

2.2 Safety Advice (Precautions)

Pos: 15.9 /All e Seri en ( All ge meine Do kum ente) ( All ge meine Mo dule) /Wi cht ige Erl äut eru nge n/Si cher hei ts hin weis e/Ei nl eitu ng Sich erh eitshi nweis e Hard ware @ 6\mod_1260180170493_21.docx @ 46720 @ @ 1

For installing and operating purposes of the relevant device to your system the

following safety precautions shall be observed:

Pos: 15.1 0. 1 /Al le S eri en ( Allg em ein e Do ku ment e) (Al lg em eine M o dul e)/ Wich tig e Erl äuter u ngen /Sic h erhei ts hinw eise /G efahr /G efahr : N ich t an G erät en un ter Spa nnung arbeite n! @ 6\mod_1260180365327_21.docx @ 46727 @ @ 1

Do not work on devices while energized!

All power sources to the device shall be switched off prior to performing any

installation, repair or maintenance work.

Pos: 15.1 0. 2 /S erie 750 ( W AGO -I/O-SY ST EM) /Wic htig e Er l äuter ung en /Sic her hei ts- un d s onsti ge H in wei se/G ef ahr/ Gefa hr: Ei nbau 07 50- xxxx nur in Geh äusen, S chrä nken oder ele ktrisc hen Betr iebsr äume n! @ 6\mod_1260180556692_21.docx @ 46731 @ @ 1

Install the device only in appropriate housings, cabinets or in electrical

operation rooms!

The WAGO-I/O-SYSTEM 750 and its components are an open system. As such,

install the system and its components exclusively in appropriate housings,

cabinets or in electrical operation rooms. Allow access to such equipment and

fixtures to authorized, qualified staff only by means of specific keys or tools.

Pos: 15.1 0. 3 /Al le S eri en ( Allg em ein e Do ku ment e) (Al lg em eine M o dul e)/ Wich tig e Erl äuter u ngen /Sic h erhei ts hinw eise /G efahr /G efahr : U nfal l verh ütung sv orsc hri ft en b each ten! @ 6\mod_1260180657000_21.docx @ 46735 @ @ 1

Pos: 15.1 0. 4 /Al le S eri en ( Allg em ein e Do ku ment e) (Al lg em eine M o dul e)/ Wich tig e Erl äuter u ngen /Sic h erhei ts hinw eise /G efahr /G efahr : A uf normg er echt e n Ansc hlu ss ac hten! @ 6 \mod_1260180753479_21.docx @ 46739 @ @ 1

Pos: 15.1 1 / Alle Ser ie n (All ge mein e M odul e) /Wic hti ge Erlä ut erung en/ Sic her heits - un d so nsti ge Hin weis e/G ef ahr/ Gef ahr: Lei tung en nur in s pa nnu ngsf rei em Z ust and ansc hl iess en oder tr enn en @ 16\mod_1372153982130_21.docx @ 124277 @ @ 1

Only connect or disconnect lines when power is safely isolated!

The lines to the device can carry hazardous voltages and currents. Contact with

the lines when live can result in severe injury or death. Therefore, read and

observe the following safety rules before you perform work on the device:

1. Disconnect the respective system component from the power supply.

2. Secure the system component against unintentional restart.

3. Check if the voltage is positively isolated.

Pos: 15.1 2. 1 /Al le S eri en ( Allg em ein e Do ku ment e) (Al lg em eine M o dul e)/ Wich tig e Erl äuter u ngen /Sic h erhei ts hinw eise /Ac htu ng/A cht ung : Defek te oder besch ädigt e Gerät e austaus chen! @ 6\mod_1260180857358_21.docx @ 46743 @ @ 1

Replace defective or damaged devices!

Replace defective or damaged device/module (e.g., in the event of deformed

contacts), since the long-term functionality of device/module involved can no

longer be ensured.

Pos: 15.1 2. 2 /Al le S eri en ( Allg em ein e Do ku ment e) (Al lg em eine M o dul e)/ Wich tig e Erl äuter u ngen /Sic h erhei ts hinw eise /Ac htu ng/A cht ung : G erät e vor kriec hen den und i sol ier e nden Sto ffen s chütz en! @ 6\mod_1260181036216_21.docx @ 46747 @ @ 1

12 Important Notes WAGO-I/O-SYSTEM 750

753-509 2DO 230V AC 0.3A/SSR

Manual

Version 1.1.0

Protect the components against materials having seeping and insulating

properties!

The components are not resistant to materials having seeping and insulating

properties such as: aerosols, silicones and triglycerides (found in some hand

creams). If you cannot exclude that such materials will appear in the component

environment, then install the components in an enclosure being resistant to the

above-mentioned materials. Clean tools and materials are imperative for handling

devices/modules.

Pos: 15.1 2. 3 /Al le S eri en ( Allg em ein e Do ku ment e) (Al lg em eine M o dul e)/ Wich tig e Erl äuter u ngen /Sic h erhei ts hinw eise /Ac htu ng/A cht ung : Rei nig ung nur mi t zul äss ig en M at erial ien! @ 6\mod_1260181203293_21.docx @ 46751 @ @ 1

Clean only with permitted materials!

Clean soiled contacts using oil-free compressed air or with ethyl alcohol and

leather cloths.

Pos: 15.1 2. 4 /Al le S eri en ( Allg em ein e Do ku ment e) (Al lg em eine M o dul e)/ Wich tig e Erl äuter u ngen /Sic h erhei ts hinw eise /Ac htu ng/A cht ung : K ein K ont a ktspra y verw end en! @ 6\ mod_1260181290808_21.docx @ 46755 @ @ 1

Do not use any contact spray!

Do not use any contact spray. The spray may impair contact area functionality in

connection with contamination.

Pos: 15.1 2. 5 /Al le S eri en ( Allg em ein e Do ku ment e) (Al lg em eine M o dul e)/ Wich tig e Erl äuter u ngen /Sic h erhei ts hinw eise /Ac htu ng/A cht ung : V erpol ung ver mei de n! @ 6\mod_1260184045744_21.docx @ 46767 @ @ 1

Do not reverse the polarity of connection lines!

Avoid reverse polarity of data and power supply lines, as this may damage the

devices involved.

Pos: 15.1 2. 6 /Al le S eri en ( Allg em ein e Do ku ment e) (Al lg em eine M o dul e)/ Wich tig e Erl äuter u ngen /Sic h erhei ts hinw eise /Ac htu ng/A cht ung : Elektr ostat isch e Entla dung v ermeid en! @ 6\mod_1260181364729_21.docx @ 46759 @ @ 1

Avoid electrostatic discharge!

The devices are equipped with electronic components that may be destroyed by

electrostatic discharge when touched. Please observe the safety precautions

against electrostatic discharge per DIN EN 61340-5-1/-3. When handling the

devices, please ensure that environmental factors (personnel, work space and

packaging) are properly grounded.

Pos: 16 /Doku ment ation all gemei n/Gli eder ungsel eme nte/---Seit en wechs el--- @ 3\mod_1221108045078_0.docx @ 21810 @ @ 1

WAGO-I/O-SYSTEM 750 Device Description 13

753-509 2DO 230V AC 0.3A/SSR

Manual

Version 1.1.0

Pos: 17 /A ll e Ser ien (Al lg emei ne M odul e)/Üb erschr ifte n für alle S erie n/Gerä tebes chrei bung /Gerä tebesc hreib ung - Üb ersc hrift 1 @ 3\ mod_1233756084656_21.docx @ 27096 @ 1 @ 1

3 Device Description

Pos: 18.1 .1 /Ser ie 7 53 ( WAG O-I/ O-SYST EM) /Gerä tebes chrei bung /Einlei tung /Anw endung /DO/A nwen dung 75 3-0509 @ 21\mod_1414156793438_21.docx @ 166534 @ @ 1

The I/O module 753-509 (2DO 230V AC 0.3A/SSR) uses voltages up to 230 V

AC/DC for connected actuators or universal supply voltage loads.

Pos: 18.1 .2 /Ser ie 7 53 ( WAGO-I/ O-SYST EM) /Ger äte besc hrei bu ng/Ei nlei tu ng/I/ O-B eschr eibu ng/D O/I /O-B eschr eibu ng 75x-05 xx 2 DO 2-Lei ter (D O, N ) + Fu nkti ons erde (F E) @ 21 \mod_1414156882555_21.docx @ 166538 @ @ 1

The I/O module has 2 output channels, providing a direct connection to 2

actuators with functional ground connection.

The actuators are connected to the following CAGE CLAMP

®

connectors

directly: signal output DO 1 and N or signal output DO 2 and N.

Pos: 18.1 .3 /Ser ie 7 50 ( WAG O-I/ O-SYST EM) /Gerä teb esc hrei bung /Ei nlei tung /I/O- Besc hrei bu ng/Al lg emei n/V er weis auf Kapi tel " Ansc hlüs se" @ 8\mod_1276775378035_21.docx @ 57956 @ @ 1

The assignment of the connections is described in the “Connectors” section.

Pos: 18.1 .4 /Ser ie 7 50 ( WAG O-I/ O-SYST EM) /Gerä teb eschr ei bung/ Einl eit ung/ I/O-B esc hrei bu ng/Al lg emei n/V er weis auf Kapi tel "G erät e ansc hli eßen" > "A nschl us sbei spi el(e) " @ 5\ mod_1246015203281_21.docx @ 36298 @ @ 1

Connection examples are shown in section “Connecting Devices” > … >

“Connection Example(s)”.

Pos: 18.1 .5 /S eri e 7 53 ( WAG O-I/ O-SYST EM) /Ger äte besc hrei bu ng/Ei nlei tu ng/I/ O-B eschr eibu ng/D O/I /O-B eschr eibu ng 753-0 509 H oc hleis tu ngs- MOSF ETs @ 2 1\mod_1414157149384_21.docx @ 166542 @ @ 1

As a switching relay, there are two high-performance MOSFETs in the I/O

module. The actuators can be mechanically controlled continuously and free of

wear from the I/O module's semiconductor outputs. The MOSFETs are non-

isolated, i.e., the potential for the field supply touches one of the relay contacts (0

V … 230 V AC/DC).

Pos: 18.1 .6 /Ser ie 7 50 ( WAG O-I/ O-SYST EM )/G eräte bes chr eibu ng/Ei nlei tu ng/I/ O-B esc hrei bung /DO /I/O- Besc hrei bung 75 0-0509 Sc hließ er-Rel ai s @ 12\mod_1339505334211_21.docx @ 96985 @ @ 1

When a relay is closed, the field potential applied is then routed to the associated

second relay contact DO 1 or DO 2.

Pos: 18.1 .7 /Ser ie 7 50 ( WAG O-I/ O-SYST EM )/G erä teb esc hrei bu ng/Ei nlei tu ng/V ers org ung/ Ans teu eru ng d er H albl ei ter ausg äng e @ 12\mod_1339505784466_21.docx @ 97019 @ @ 1

Control of the semiconductor outputs is fully isolated.

Pos: 18.1 .8 /Ser ie 7 50 ( WAG O-I/ O-SYST EM )/G eräte bes chr eibu ng/Ei nlei tu ng/L ED-A nz eige/ LED Zu stan d R elais @ 5\mod_1246862048946_21.docx @ 36603 @ @ 1

The switching status of the two relays is indicated via green status LEDs.

Pos: 18 .1.9 /S erie 750 (WAGO-I/ O-S YSTEM )/G erä teb eschr ei bung/ Einl eit ung/ LED-A nzei ge/Ver weis auf Kapi tel "Anz eige elem ente" @ 5\ mod_1246010525000_21.docx @ 36194 @ @ 1

The meaning of the LEDs is described in the “Display Elements” section.

Pos: 18.1 .1 0 /S erie 750 ( W AGO -I/O-SY ST EM)/Wi chti g e Erl äu ter ung en/Si cher hei ts- und s ons tig e Hi nw eise /Hin wei s/Hi n weis : Ei nspei se kle mme für Ver sorg ung ung leic h 24 V ei nsetz en @ 5\ mod_1247032609340_21.docx @ 36784 @ @ 1

Use additional supply module!

Use an additional supply module if I/O modules require a field supply not equal to

24 VDC. Insert the supply module in front of the module that requires the

different supply.

Pos: 18.1 .1 1 /S erie 753 ( W AGO -I/O-SY ST EM)/G eräte beschr eib ung/Ei nleit ung/ Versor gung /Vers orgung AC/DC 0. ..23 0 V, N und Er de über Leistu ngs kontakt e @ 21\mod_1414157661006_21.docx @ 166546 @ @ 1

The I/O module receives the 0 V ... 230 V AC/DC power supply, the N potential

and the ground potential for the field level from an upstream I/O module and

makes the potentials available to subsequent I/O modules via the power jumper

contacts designed as spring contacts.

Pos: 18.1 .1 2 /S erie 750 ( W AGO -I/O-SY ST EM) /Wic htig e Er l äuter ung en /Sic her hei ts- un d s onsti ge H in wei se/Ac htung /Acht ung: Maximal er Str om Leis tungs konta kte 10 A @ 3\ mod_1226499143500_21.docx @ 25029 @ @ 1

Do not exceed maximum current via power jumper contacts!

The maximum current to flow through the power jumper contacts is 10 A.

Greater currents can damage the contacts.

When configuring your system, ensure that this current is not exceeded. If

exceeded, insert an additional supply module.

Pos: 18.1 .1 3 /S erie 750 ( W AGO -I/O-SY ST EM)/ Gerät ebe schr eib ung/ Einl eit ung/ Ein satz berei ch/ Ein satz berei ch 7 50-xxxx all e Ko ppl er/C o ntroll er oh ne Ei nsc hrä nku ng @ 3\ mod_1232541691906_21.docx @ 26522 @ @ 1

The I/O module 753-509 can be used with all fieldbus couplers/controllers of the

WAGO-I/O-SYSTEM 750.

14 Device Description WAGO-I/O-SYSTEM 750

753-509 2DO 230V AC 0.3A/SSR

Manual

Version 1.1.0

Pos: 18.2 /Dokumentation all ge mein/ Glie der ungs ele mente /---Seit en wechs el--- @ 3\mod_1221108045078_0.docx @ 21810 @ @ 1

Pos: 18.3 /All e Seri en ( All ge meine Mo dul e)/Ü bers chr ift en f ür alle S erie n/Ger äte bes chr eib ung /Ans ic ht - Ü ber schri ft 2 @ 4\mod_1240984217343_21.docx @ 31958 @ 2 @ 1

3.1 View

Pos: 18.4 /Serie 753 (WAGO-I/O-SYST EM )/Hi n weis e zur D okum ent atio n/Hi n weis z u m Zub ehör tei l 75 3-110 @ 20\mod_1411023611789_21.docx @ 163868 @ @ 1

Depiction of the I/O module with 753-110 Connector!

Information on this pluggable connection pertains to the 753-110 Connector,

which is not included with the I/O module.

Pos: 18.5 /Serie 753 (WAGO-I/O-SYST EM )/ Ger äteb esc hrei bung /Ans ic ht/ Dig itala usg ang skle mm en/A nsic ht 753- 050 9 @ 12\mod_1339591495988_21.docx @ 97254 @ @ 1

Figure 1: View

Pos: 18.6 /Serie 753 (WAGO-I/O-SYST EM) /Ger äte besc hrei bu ng/A nsic ht/A nsi cht – Leg ende mit Leist ungsk ontakten_mit Kodierung, Kabelbefestigung und Prüföffnungen @ 20\mod_1411031302199_21.docx @ 163871 @ @ 1

Table 3: Legend for Figure “View”

Pos.

Description

Details See Section

1

Marking possibility with Mini-

WSB

---

2

Status-LEDs

“Device Description” > “Display

Elements”

3

Data contacts

“Device Description” > “Connectors”

4

CAGE CLAMP

®

connectors

“Device Description” > “Connectors”

5

Release tab

“Mounting” > “Inserting and Removing

Devices” and “I/O Modules with

Pluggable Wiring Level (Series 753)”

6

Coding possibility with coding

fingers

“Mounting” > “Coding”

7

Power jumper contacts

“Device Description” > “Connectors”

8

Test port

---

9

Fixing lug for cable ties

“Mounting” > “I/O Modules with

Pluggable Wiring Level (Series 753)”

Pos: 18.7 /Dokumentation allgemein/Gliederungselemente/---Seite nwechs el--- @ 3\ mod_1221108045078_0.docx @ 21810 @ @ 1

WAGO-I/O-SYSTEM 750 Device Description 15

753-509 2DO 230V AC 0.3A/SSR

Manual

Version 1.1.0

Pos: 18.8 /All e Seri en ( All ge meine Mo dul e)/Ü bers chr ift en f ür alle S erie n/Ger äte bes chr eib ung /Ans chl üss e - Üb ersc hrift 2 @ 4\ mod _1240984262656_21.docx @ 31961 @ 2 @ 1

3.2 Connectors

Pos: 18.9 /Serie 750 (WAGO-I/O-SYST EM) /Ger äte besc hrei bu ng/A nsc hlüss e/D ate nkon takt e/Kl em menbus - Ü bersc hrift 3 @ 6\ mod_1256294684083_21.docx @ 43660 @ 3 @ 1

3.2.1 Data Contacts/Internal Bus

Pos: 18.1 0. 1 /S erie 750 ( W AGO -I/O-SY ST EM)/ Gerät ebe schr eib ung/ Ans chl üsse/ Dat en konta kte - Fel dbus koppl er/ -contr oll er, Abbil dung und Bes chrei bung @ 3\ mod_1231771259187_21.docx @ 26002 @ @ 1

Communication between the fieldbus coupler/controller and the I/O modules as

well as the system supply of the I/O modules is carried out via the internal bus. It

is comprised of 6 data contacts, which are available as self-cleaning gold spring

contacts.

Figure 2: Data Contacts

Pos: 18.1 0. 2 /S erie 750 ( W AGO -I/O-SY ST EM) /Wic htig e Er l äuter ung en /Sic her heits - un d so nstig e Hi n weis e/Ac ht ung /Acht ung : B uskl e mmen nich t au f G ol dfed er konta kte l eg en! @ 7\ mod_1266318463636_21.docx @ 50695 @ @ 1

Do not place the I/O modules on the gold spring contacts!

Do not place the I/O modules on the gold spring contacts in order to avoid soiling

or scratching!

Pos: 18.1 0. 3 /S erie 750 ( W AGO -I/O-SY ST EM) /Wic htig e Er l äuter ung en /Sic her hei ts- un d so nsti ge Hi n weis e/Ac ht ung /Ac htung : E SD - Auf gute Erdung der Umgebung achten! @ 7\mod_1266318538667_21.docx @ 50708 @ @ 1

Ensure that the environment is well grounded!

The devices are equipped with electronic components that may be destroyed by

electrostatic discharge. When handling the devices, ensure that the environment

(persons, workplace and packing) is well grounded. Avoid touching conductive

components, e.g. data contacts.

Pos: 18.1 1 /D ok um entati o n allg em ein/ Gli eder ung sel eme nte/---S eit enw echs el--- @ 3\ mod_1221108045078_0.docx @ 21810 @ @ 1

16 Device Description WAGO-I/O-SYSTEM 750

753-509 2DO 230V AC 0.3A/SSR

Manual

Version 1.1.0

Pos: 18.1 2 / Ser ie 7 50 ( WAG O-I/ O-SYST EM) /Ger äte besc hrei bu ng/A nsc hlüss e/L eist ungs ko ntakt e/F eldv ers orgung - Ü bers chri ft 3 @ 6\mod_1256294692864_21.docx @ 43664 @ 3 @ 1

3.2.2 Power Jumper Contacts/Field Supply

Pos: 18.1 3.1 / S erie 750 ( W AGO- I/O-SY ST EM)/Wi cht ig e Erl äu ter ung en/Si cher hei ts - un d so nstig e Hi n weis e/V orsi cht /Vor sic ht: Ver letz ung sgef a hr dur c h schar f kanti ge Mes ser kon takt e! @ 6\ mod_1256193279401_21.docx @ 43414 @ @ 1

Risk of injury due to sharp-edged blade contacts!

The blade contacts are sharp-edged. Handle the I/O module carefully to prevent

injury.

Pos: 18.1 3. 2 /S erie 750 ( W AGO -I/O-SY ST EM) /Ger äte bes chr eib ung/ Ans chl üss e/L eist ungs kon tak te 3 LK ( M esser /Fe der ) - Ei nlei tu ng @ 15\ mod_1371723761988_21.docx @ 123734 @ @ 1

The I/O module 753-509 has 3 self-cleaning power jumper contacts that supply

and transmit power for the field side. The contacts on the left side of the I/O

module are designed as male contacts and the contacts on the right side as spring

contacts.

Pos: 18.1 3. 3 /S erie 753 ( W AGO -I/O-SY ST EM) /Ger äte bes chr eib ung/ Ans chl üss e/L eist ungs kon tak te/F eld ver sorg ung 3 LK ( Mess er/ Leis tu ngs kont akt e/Fel d vers orgu ng 3 LK (Me sser /Fe der ) - Abbi l dung @ 1 7\mod_1389277559533_21.docx @ 140913 @ @ 1

Figure 3: Power Jumper Contacts

Pos: 18.1 3. 4 /S erie 750 ( W AGO -I/O-SY ST EM) /Ger äte bes chr eib ung/ Ans chl üss e/L eist ungs kon tak te 3 LK ( M esser /Fe der ) - Legende @ 15\mod_1371723810708_21.docx @ 123742 @ @ 1

Table 4: Legend for Figure “Power Jumper Contacts”

Contact

Type

Function

1 Spring contact

Potential transmission (U

v

)

for field supply

2 Spring contact

Potential transmission (0 V)

for field supply

3 Spring contact

Potential transmission (ground)

for field supply

4 Blade contact

Potential feed-in (ground)

for field supply

5 Blade contact

Potential feed-in (0 V)

for field supply

6 Blade contact

Potential feed-in (U

v

)

for field supply

Pos: 18.1 3. 5 /S erie 750 ( W AGO -I/O-SY ST EM) /Wic htig e Er l äuter ung en /Sic her hei ts- un d so nsti ge Hi n weis e/Ac ht ung /Ac htung : M axi maler St ro m Lei stu ngs kont a kte 1 0 A @ 3 \mod_1226499143500_21.docx @ 25029 @ @ 1

WAGO-I/O-SYSTEM 750 Device Description 17

753-509 2DO 230V AC 0.3A/SSR

Manual

Version 1.1.0

Do not exceed maximum current via power jumper contacts!

The maximum current to flow through the power jumper contacts is 10 A.

Greater currents can damage the contacts.

When configuring your system, ensure that this current is not exceeded. If

exceeded, insert an additional supply module.

Pos: 18.1 4 /D ok um entati o n allg em ein/ Gli eder ung sel eme nte/---S eit enw echs el--- @ 3\ mod_1221108045078_0.docx @ 21810 @ @ 1

18 Device Description WAGO-I/O-SYSTEM 750

753-509 2DO 230V AC 0.3A/SSR

Manual

Version 1.1.0

Pos: 18.1 5 / Ser ie 7 50 ( WAG O-I/ O-SYST EM )/G erät ebe schr eib ung /A nsc hlüss e/C AGE C L AMP-A nschlüsse - Ü bersc hrift 3 @ 6\mod_1256296337770_21.docx @ 43674 @ 3 @ 1

3.2.3 CAGE CLAMP

®

Connectors

Pos: 18.1 6 / Ser ie 7 53 ( WAG O-I/ O-SYSTEM)/Hinweise zur Dokumentation/Hinweis zum Zubehörteil 753-110 @ 20\mod_1411023611789_21.docx @ 163868 @ @ 1

Depiction of the I/O module with 753-110 Connector!

Information on this pluggable connection pertains to the 753-110 Connector,

which is not included with the I/O module.

Pos: 18.1 7 / Ser ie 7 53 ( WAG O-I/ O-SYST EM )/G erät ebe schr eib ung /A nsc hlüss e/Di git ala usg ang skle mm en/A nsc hlü sse 75 3-050 9 @ 12\mod_1339591961780_21.docx @ 97279 @ @ 1

Figure 4: CAGE CLAMP

®

Connectors

Table 5: Legend for Figure “CAGE CLAMP

®

Connectors”

Channel

Designation

Connector

Function

1

DO 1

1

Output DO 1: Signal voltage

230 V

2

Output DO 1: Field supply

N

3

Output DO 1: Neutral conductor

Ground

4

Output DO 1: Ground

2

DO 2

5

Output DO 2: Signal voltage

230 V

6

Output DO 2: Field supply

N

7

Output DO 2: Neutral conductor

Ground

8

Output DO 2: Ground

Pos: 18.1 8 /D ok um entati o n allg em ein/ Gli eder ung sel eme nte/---S eit enw echs el--- @ 3\ mod_1221108045078_0.docx @ 21810 @ @ 1

WAGO-I/O-SYSTEM 750 Device Description 19

753-509 2DO 230V AC 0.3A/SSR

Manual

Version 1.1.0

Pos: 18.1 9 / Alle Ser ie n (All ge mein e M odul e) /Üb ersc hri ften für all e S eri en/G erät ebes chr eibung /A nzeig eel eme nte - Über sc hrift 2 @ 4\ mod_1240984390875_21.docx @ 31964 @ 2 @ 1

3.3 Display Elements

Pos: 18.2 0 / Ser ie 7 50 ( WAG O-I/ O-SYST EM)/ Gerät ebesc hreib ung/ Anzeig eele mente/ Digi tala usgang skle mmen/A nzei geele mente 7 50-05xx 2 DO (Agn, Cgn) @ 10\mod_1298296792679_21.docx @ 69731 @ @ 1

Figure 5: Display Elements

Table 6: Legend for Figure “Display Elements”

Channel

Designation

LED

State

Function

1 Status DO 1 A

Off

Output DO 1: Signal voltage “0”

Green

Output DO 1: Signal voltage “1”

2 Status DO 2 C

Off

Output DO 2: Signal voltage “0”

Green

Output DO 2: Signal voltage “1”

Pos: 18.2 1 /D oku ment ati on al lg emei n/Gl i eder ung sel eme nte/---S eit enwec hs el--- @ 3\ mod_1221108045078_0.docx @ 21810 @ @ 1

20 Device Description WAGO-I/O-SYSTEM 750

753-509 2DO 230V AC 0.3A/SSR

Manual

Version 1.1.0

Pos: 18.2 2 / Alle Ser ie n (All ge mein e M odul e) /Üb ersc hri ften für all e S eri en/G erät ebes chr ei bung /Sc he matis ch es Schal tbi ld - Über schri ft 2 @ 4\mod_1240984441312_21.docx @ 31967 @ 2 @ 1

3.4 Schematic Diagram

Pos: 18.2 3 / Ser ie 7 53 ( WAG O-I/ O-SYST EM)/ Gerät ebesc hreib ung/ Schem atisc hes Sc haltbil d/Sc hemat isches Schal tbil d 753-0509 @ 21\mod_1414412676886_21.docx @ 166583 @ @ 1

Figure 6: Schematic Diagram

Pos: 18.2 4 /D ok um entati o n allg em ein/ Gli eder ung sel eme nte/---S eit enw echs el--- @ 3\ mod_1221108045078_0.docx @ 21810 @ @ 1

Page is loading ...

WAGO 2-channel solid-state load relay User manual

WAGO 2-channel solid-state load relay User manual

Related papers

Other documents