Andersen 100 Series Single-Hung, Casement, Awning and Gliding Windows Installation guide

  • Hello! I am an AI chatbot trained to assist you with the Andersen 100 Series Single-Hung, Casement, Awning and Gliding Windows Installation guide. I’ve already reviewed the document and can help you find the information you need or explain it in simple terms. Just ask your questions, and providing more details will help me assist you more effectively!
9180324 BA-00 05/01/2019
Product Series: 100 Series
Product Type: Single-Hung, Casement, Awning,
and Gliding Windows
Installation Clip Application for Sill Fastening
Parts Included:
Read these instructions before starting procedure.
For additional information visit www.andersenwindows.com.
For questions call 1-888-888-7020.
Tools and Supplies Needed:
Safety
Glasses
Tape
Measure
Drill / Driver Pencil
Andersen” and all other marks where denoted are trademarks of Andersen Corporation. ©2019 Andersen Corporation. All rights reserved.
Gasket
#8 x 3/4" Pan Head
Screw with Seal
(four per clip)
Installation
Clip
· Windows and doors can be heavy. Use safe lifting techniques and a reasonable number of people with enough strength to
lift, carry, and install window and door products. Heavier windows and doors will require mechanical assistance. Failure to do
so could result in injury, product or property damage.
· Windows, doors, and installation components can have sharp edges. Wear protective equipment when handling. Failure to
do so could result in injury.
· Windows and doors have small parts (e.g. hole plugs, operator spline caps, fasteners, etc.). Small parts if swallowed could
pose a choking hazard to young children. Dispose of unused, loose, or easily removed small parts. Failure to do so could
result in injury.
· Follow manufacturers’ instructions for hand and power tools. Always wear safety glasses. Failure to do so could result in
injury, product or property damage.
Clips must be applied to the interior side of window. Failure to do so could result in product or property damage.
1 2
Remove liner from one side of gasket and position gasket on installation clip. Remove
second liner and place installation clip with gasket onto unit. Fasten installation clip(s) with
screws provided. Installation clip will be bent away from the window frame when attaching
installation clip to opening
Place unit interior side up on a clean at work surface.
Determine quantity and location of installation clip(s)
needed from chart below. Clean area where installation
clips will be attached using soap and water. Surface
must be dry before applying installation clips.
2
9180324
Installation Clip Location Chart
PG30/40
PG50
Single-Hung Windows - For integral combinations with a total unit width greater than
47-1/2”, apply an installation clip under both sides of each integral post. For integral
combinations with a center unit that alone exceeds 47-1/2” in width, apply one
additional installation clip to the sill at midpoint of the center unit.
Gliding Windows - For single units with a unit width greater than 47-1/2”, apply an
installation clip under both sides of each meeting stile. For units where the center
sash alone exceeds 47-1/2” in width, apply one additional installation clip to the sill
at the midpoint of the center sash.
Single-Hung Windows - For integral combinations with a total unit width greater than 47-1/2”, apply one
installation clip under each integral post. For integral combinations with a center unit that alone exceeds
47-1/2” in width, apply one additional installation clip to the sill at midpoint of the center unit.
Gliding Windows - For single units with a unit width greater than 47-1/2”, apply one installation clip under each meeting stile. For
units where the center sash alone exceeds 47-1/2” in width, apply one additional installation clip to the sill at the midpoint of the
center sash.
Casement and Awning Windows - For integral combinations with a total unit
width greater than 47-1/2”, apply one installation clip under each integral post.
Casement and Awning Windows - For integral combinations with a total unit width greater
than 47-1/2”, apply an installation clip under both sides of each integral post.
> 47-1/2"
> 47-1/2"
> 47-1/2"
> 47-1/2"
/