Classic Exhibits VK-2993 Setup Instructions

Classic Exhibits
Brand
Classic Exhibits
Model
VK-2993
Type
Setup Instructions
© 2017
www.classicexhibits.com
Order #XXXXX
SETUP INSTRUCTIONS
If you would like to tell us about your experience with your setup instructions please email us at [email protected]
VK-2993 10’x20’ Backlit Hybrid Display
Plan View
10’
20’
© 2017
www.classicexhibits.com
Order #XXXXX
DO NOT USE POWER TOOLS
ALL CONNECTIONS MUST
BE TIGHTLY SECURED
Part Identification - Numbering
Spline Connection Base Plate & Extrusion Connection
General Setup Instructions
- Read entire setup instruction manual prior to
unpacking parts and pieces.
- The setup instructions are created specifically
for this configuration.
- Setup instructions are laid out sequentially in
steps, including exploded views with detailed
explanation for assembly.
WARNING
Cleaning & Packing
- For Cleaning Metal, Plex, & Laminate Parts:
Use a MILD NON-ABRASIVE cleanser and
soft cloth/paper towel to clean all surfaces.
- Keep exhibit components away from heat
and prolonged sun exposure.
Heat and UV exposure will warp and
fade components.
- Retain all provided Packing Materials.
All provided packing materials are for
ease of repacking & component protection.
Disassembly
- For loss prevention, tighten all setscrews
and locks during disassembly
7A
Hex Tool - Essential for Assembly
Extrusion & Lock Connection Engaged Lock
LADDERS OR LIFTS
MAY BE REQUIRED
General Information
© 2017
www.classicexhibits.com
Order #XXXXX General Information
Graphic Removal
To remove the graphic from
the frame, locate the fabric
pull tab. Gently pull up on the
tab to remove the fabric.
Step 1
Insert corner A. Turn edge of
graphic so silicon welt is
perpendicular to face of
graphic. Insert narrow side
of welt with fabric to outside
into the channel. Repeat for
other side of this corner.
Step 2
Repeat Step 1 for opposite
corner C, then insert corner
B, followed by corner D, to
complete the installation of
the corners.
Step 3
Once all corners are inserted,
press one silicon edge into
channel from corners and
work toward the center.
Make sure welt is fully inserted
into channel. Continue until
all sides are done. Smooth
out edges of graphic.
SEG Graphic Installation
It is important to first insert
graphic into each alternate
corner then to the sides of
the frame. If this is not done,
graphic will not fit into the
frame correctly.
Corner A
Corner D
Corner B
Corner C
© 2017
www.classicexhibits.com
Order #XXXXX General Information
CEI-110 Profile
Straight Connection
Corner Connection
TS RV 4
Bracket
Insert Bracket
into the Interior
Center Slot
of extrusion.
Slide connecting
extrusion over
exposed end
of bracket.
Secure extrusion
using remaining
set screws.
Set
Screw
CEI-110 Frames Assembly
Disassembly
1) Loosen set screws on brackets, then slide
extrusions off of brackets.
Straight Bracket Installation (when required)
1) Slide TWO-PIECE TS RV 4 straight bracket into
Interior Center Slot of extrusion so that two of the
set screws are inside groove.
Tighten two set screws to secure.
2) Slide connecting extrusion over exposed end
of bracket. Tighten two remaining set screws
to secure.
Corner Bracket Installation
1) Slide TWO-PIECE TS RV 2 L-bracket into
Interior Center Slot of extrusion so that two
set screws are inside groove.
Tighten two set screws to secure.
2) Slide one A1 L-Bracket into outer interior
grooves of upper and lower horizontals.
Tighten set screws to secure.
3) Slide vertical extrusion over exposed ends
of brackets in lower horizontal.
Tighten set screws to secure.
4) Slide exposed ends of installed brackets of
upper horizontal into open ends of verticals.
Tighten set screws to secure.
TS RV 2
Upper
Horizontal
Lower
Horizontal
Upper
Horizontal
Lower
Horizontal
TS RV 2
8 Brackets Total:
(4) - TS RV 4
(4) - A1 L-Brackets
A1
A1
Slide verticals over
brackets of lower
horizontal, then slide
upper horizontal &
brackets into grooves
& center slots
of verticals.
Completed
Assembly
Insert L-Brackets into the
Interior Center Slot & outer
interior grooves of extrusion.
Completed
Assembly
Secure inserted half
of bracket, using
set screws.
© 2017
www.classicexhibits.com Case 1 of 5
Order #XXXXX Case Packing - 1 of 5
Door
3/4/7/7A
1/1A/2/2A
5,5A,6,6A
Counter
Top
Shelf
Infills
Top View of Each Level
Level 1 Level 2 Level 3 Level 4
© 2017
www.classicexhibits.com Case 2 of 5
Order #XXXXX Case Packing - 2 of 5
20,20A
21
1618 18A 19 19A 16A 17 17A
21A
Base
Plate
(qty 2)
Graphics
Setup Hardware
Top View of Each Level
Level 1 Level 2 Level 3
© 2017
www.classicexhibits.com Case 3 of 5
Order #XXXXX Case Packing - 3 of 5
Top View of Each Level
Level 1 Level 2 Level 3
5 5A 6A6
Infill
(qty 4)
7 7A 8A8
Graphics
Graphics
Setup Hardware
© 2017
www.classicexhibits.com Case 4 of 5
Order #XXXXX Case Packing - 4 of 5
Top View of Each Level
Level 1 Level 2 Level 3 Level 4
3 3A 4A4 11,11A
12,12A
14,14A
15,15A
2
10,10A
10B
13,13A
13B
2A
Base
Plate
(qty 2)
Base
Plate
(qty 2)
9,9A
© 2017
www.classicexhibits.com Case 5 of 5
Order #XXXXX Case Packing - 5 of 5
Door
3/4/7/7A
1/1A/2/2A
5,5A,6,6A
Counter
Top
Shelf
Infills
Top View of Each Level
Level 1 Level 2 Level 3 Level 4
© 2017
www.classicexhibits.com Step 1 of 8
Order #XXXXX Left Side Lightbox Assembly
Steps:
1) Attach Base Plates [1] to horizontal [2] using
bolts & wing nuts.
2) Connect verticals [3-3A], [4-4A] together.
See CEI-110 Straight Connection detail.
3) Attach horizontals [2,2A] between vertical
assemblies [3/3A] & [4/4A].
See CEI-110 Corner Connection detail.
4) Connect horizontals [5-6], [5A-6A] together,
& connect verticals [7-7A], [8-8A] together.
See CEI-110 Straight Connection detail.
5) Attach Base Plates [1A] to horizontal
assembly [5/6], using bolts & wing nuts.
6) Attach horizontal assemblies [5/6], [5A/6A]
between vertical assemblies [7/7A], [8/8A].
See CEI-110 Corner Connection detail.
7) Connect verticals [9,9A] between horizontal
assemblies [5/6], [5A/6A].
1
2
2A
3
3A 4A
4
1
5
5A
7
7A
8A
9
9A
8
6
6A
1A 1A
Item
1,1A
2/2A
3/3A
4/4A
5/5A
6/6A
7/7A
8/8A
9/9A
Qty.
2,2
1/1
1/1
1/1
1/1
1/1
1/1
1/1
1/1
Description
Base Plate
46”w CEI110 Horizontal Extrusion
48”h CEI110 Vertical Extrusion
48”h CEI110 Vertical Extrusion
35”w CEI110 Horizontal Extrusion
35”w CEI110 Horizontal Extrusion
48”h CEI110 Vertical Extrusion
48”h CEI110 Vertical Extrusion
46.1767”h Z45 Vertical Extrusion
CEI-110 Straight Connection 1) Insert TSRV4 Bracket
into milled groove of
Extrusion.
2) Slide connecting extrusion
over exposed end of bracket.
3) Use Set screws to secure
extrusions.
TSRV4
Bracket
Set
Screws
*
CEI-110 Corner Connection
*
1) Insert TSRV2 and A1 Brackets
into milled groove of extrusion.
2) Slide connecting extrusion over
exposed end of brackets.
3) Use Set screws to secure
extrusions.
4) Use Set screws to secure
extrusions.
TSRV2
Bracket
A1
Screws
****
*
*
****
****
© 2017
www.classicexhibits.com Step 2 of 8
Order #XXXXX Left Side Return Walls
When assembled
Top View
48” V31 Connector
48” V31 Connector
V31
Small Lightbox
Left Return
Wall
Left Return
Wall
Right Return
Wall
Right Return
Wall
Large Lightbox
V31 V31
48” V31 Connector
48” V31 Connector
48” V31 Connector
48” V31 Connector
Steps:
1) Connect verticals [11-11A], [12-12A],
[14-14A], [15-15A] together.
2) Attach lower horizontal [10] between
vertical assemblies [11/11A], [12/12A];
slide lower infill between verticals and
secure with horizontal [10A]; then slide
upper infill between verticals & secure
with upper horizontal [10B].
3) Connect lower horizontal [13] between
vertical assemblies [14/14A], [15/15A];
slide lower infill between verticals, then secure
with horizontal [13A]; slide upper infill between
verticals & secure with upper horizontal [13B].
4) Attach left & right Return Wall assemblies to
Lightbox Frame assemblies using
V31 Connectors, as shown
See V31 Connection detail.
Left Return Wall
Right Return Wall
V31 Connection
Slide V31 connector
into channels of
vertical extrusions.
Tighten
set screws
to secure.
Top View
S44 CEI110
V31
Item
10,10A,10B
11/11A
12/12A
13,13A,13B
14/14A
15/15A
--
Qty.
1/1
1/1
1/1
1/1
1/1
1/1
6
Description
15”w Z45 Horizontal Extrusion
48”h S40 Vertical Extrusion
48”h S40 Vertical Extrusion
15”w Z45 Horizontal Extrusion
48”h S40 Vertical Extrusion
48”h S40 Vertical Extrusion
48”h V31 Connector
10
10A
10B
13
13B
13A
14
14A
15
15A
11
11A
12A
12
© 2017
www.classicexhibits.com Step 3 of 8
Order #XXXXX Right Side Lightbox Assembly
Item
1C
16/16A
17/17A
18/18A
19/19A
20/20A
21/21A
Qty.
2
1/1
1/1
1/1
1/1
1/1
1/1
Description
Base Plate
46”w CEI110 Horizontal Extrusion
46”w CEI110 Horizontal Extrusion
48”h CEI110 Vertical Extrusion
48”h CEI110 Vertical Extrusion
46.177”h Z45 Vertical Extrusion
26”w CEI110 Horizontal Extrusion
16
1C
1C
17
21
17A
21A
18A
19A
20A
18
19
20
16A
Steps:
1) Connect horizontals [16-21-17], [16A-21A-17A] together,
& connect verticals [18-18A], [19-19A] together.
See CEI-110 Straight Connection detail.
5) Attach Base Plates [1B] to horizontal
assembly [16/21/17], using bolts & wing nuts.
6) Attach horizontal assemblies [16/21/17], [16A/21A/17A]
between vertical assemblies [18/18A], [19/19A].
See CEI-110 Corner Connection detail.
7) Connect verticals [20,20A] between horizontal
assemblies [16/21/17], [16A/21A/17A].
*
**
*
*
*
**
**
CEI-110 Straight Connection 1) Insert TSRV4 Bracket
into milled groove of
Extrusion.
2) Slide connecting extrusion
over exposed end of bracket.
3) Use Set screws to secure
extrusions.
TSRV4
Bracket
Set
Screws
*
CEI-110 Corner Connection
*
1) Insert TSRV2 and A1 Brackets
into milled groove of extrusion.
2) Slide connecting extrusion over
exposed end of brackets.
3) Use Set screws to secure
extrusions.
4) Use Set screws to secure
extrusions.
TSRV2
Bracket
A1
Screws
© 2017
www.classicexhibits.com Step 4 of 8
Order #XXXXX Right Side Lightbox Connection
When assembled
Top View
Right Lightbox
Steps:
1) Attach Right Lightbox to vertical assembly [15/15A]
using V31 connectors. See V31 Connection detail.
V31 Connection
Slide V31 connector
into channels of
vertical extrusions.
Tighten
set screws
to secure.
Top View
S44 CEI110
V31
Item
--
Qty.
2
Description
48”h V31 Connector
V31
15/15A
15/15A
48” V31 Connector48” V31 Connector
© 2017
www.classicexhibits.com Step 5 of 8
Order #XXXXX Lightbox Wiring
Steps:
1) Connect power cords to Supernova lights as shown.
+
-
Power
Female
Transformer
Light to Tranformer Attachment
++
--
Lights
Male
Light to Light Attachment
Maximum of 7 lights per chain / 9 lights per Transformer
Power
Break Power
Break
Power
Break
to
power
to
power
to
power
Transformer Transformers
Transformers
Power
Break
to
power
to
power
Transformers
Transformers
Power
Break
Power
Break
© 2017
www.classicexhibits.com Step 6 of 8
Order #XXXXX SEG Graphics
Steps:
1) Apply SEG graphics to front of display.
2) Apply SEG blockers to back of display.
SEG Graphic Installation
Corner A
Corner D
Corner B
Corner C
It is important to first insert
graphic into each alternate
corner then to the sides of
the frame. If this is not done,
graphic will not fit into the
frame correctly.
Step 1
Insert corner A. Turn edge of
graphic so silicon welt is
perpendicular to face of
graphic. Insert narrow side
of welt with fabric to outside
into the channel. Repeat for
other side of this corner.
Step 2
Repeat Step 1 for opposite
corner C, then insert corner
B, followed by corner D, to
complete the installation of
the corners.
Step 3
Once all corners are inserted,
press one silicon edge into
channel from corners and
work toward the center.
Make sure welt is fully inserted
into channel. Continue until
all sides are done. Smooth
out edges of graphic.
Graphic Removal
To remove the graphic from
the frame, locate the fabric
pull tab. Gently pull up on
the tab to remove the fabric.
SE
G
Gr
a
phic
SE
G
Gr
a
phic
SE
G
Gr
a
phic
SE
G
Bl
o
cke
r
SE
G
Bl
o
cke
r
SE
G
Bl
o
cke
r
© 2017
www.classicexhibits.com Step 7 of 8
Order #XXXXX MOD-1701 Reception Counter (Left)
When assembled
Steps:
1) Connect horizontals [1,1A] between verticals [2,2A],
sliding blocker infill between verticals.
See CEI-110 Corner Connection detail.
2) Attach horizontal [5] between verticals [2A,4];
slide infill between verticals & secure with
horizontal [5A].
3) Attach horizontal [6] between verticals [2,3];
slide infill between verticals & secure with
horizontal [6A].
4) Attach horizontals [7,7A] between verticals [3,4].
5) Install Door between verticals [3,4].
See Door Attachment detail.
6) Affix shelf supports to inside of counter using
Velcro; place Internal Shelf.
7) Place Counter Top onto assembly.
8) Attach power cords to Supernova lights as shown.
9) Apply SEG Graphic to front lightbox.
Counter Top
Transformer
Shelf
shelf suppoprt
Door Stop
Door Hinge
shelf suppoprt
shelf suppoprt
shelf suppoprt
BACK SIDE
1
1A
2
5
3
6
46A
7A
7
5A
2A
Item
1/1A
2/2A
3
4
5/5A
6/6A
7/7A
Qty.
1/1
1/1
1
1
1/1
1/1
1/1
Description
22.1654”w CEI110 Horizontal Extrusion
38”h CEI110 Vertical Extrusion w/ attached S10
38”h S44 Vertical Extrusion w/ Door Hinge
38”h S44 Vertical Extrusion w/ Door Stop
16”w Z45 Horizontal Extrusion
16”w Z45 Horizontal Extrusion
18.5”w Z45 Horizontal Extrusion
Door
Hinge
Hinge
Slide pin into
hinge attached
to vertical.
Slide door
hinge over pin.
Door Attachment
*
Pin
CEI-110 Corner Connection
*
1) Insert TSRV2 and A1 Brackets
into milled groove of extrusion.
2) Slide connecting extrusion over
exposed end of brackets.
3) Use Set screws to secure
extrusions.
4) Use Set screws to secure
extrusions.
TSRV2
Bracket
A1
Screws
+
-
Power
Female
Transformer
Light to Tranformer Attachment
SEG Graphic Installation
Corner A
Corner D
Corner B
Corner C
It is important to first insert
graphic into each alternate
corner then to the sides of
the frame. If this is not done,
graphic will not fit into the
frame correctly.
Step 1
Insert corner A. Turn edge of
graphic so silicon welt is
perpendicular to face of
graphic. Insert narrow side
of welt with fabric to outside
into the channel. Repeat for
other side of this corner.
Step 2
Repeat Step 1 for opposite
corner C, then insert corner
B, followed by corner D, to
complete the installation of
the corners.
Step 3
Once all corners are inserted,
press one silicon edge into
channel from corners and
work toward the center.
Make sure welt is fully inserted
into channel. Continue until
all sides are done. Smooth
out edges of graphic.
Graphic Removal
To remove the graphic from
the frame, locate the fabric
pull tab. Gently pull up on
the tab to remove the fabric.
B
l
o
c
k
er Infi
l
l
D
o
o
r
I
nf
i
ll
I
nf
i
ll
Maximum of 3 lights per Transformer
© 2017
www.classicexhibits.com Step 8 of 8
Order #XXXXX MOD-1701 Reception Counter (Right)
Steps:
1) Connect horizontals [1,1A] between verticals [2,2A],
sliding blocker infill between verticals.
See CEI-110 Corner Connection detail.
2) Attach horizontal [5] between verticals [2A,4];
slide infill between verticals & secure with
horizontal [5A].
3) Attach horizontal [6] between verticals [2,3];
slide infill between verticals & secure with
horizontal [6A].
4) Attach horizontals [7,7A] between verticals [3,4].
5) Install Door between verticals [3,4].
See Door Attachment detail.
6) Affix shelf supports to inside of counter using
Velcro; place Internal Shelf.
7) Place Counter Top onto assembly.
8) Attach power cords to Supernova lights as shown.
9) Apply SEG Graphic to front lightbox.
Item
1/1A
2/2A
3
4
5/5A
6/6A
7/7A
Qty.
1/1
1/1
1
1
1/1
1/1
1/1
Description
22.1654”w CEI110 Horizontal Extrusion
38”h CEI110 Vertical Extrusion w/ attached S10
38”h S44 Vertical Extrusion w/ Door Hinge
38”h S44 Vertical Extrusion w/ Door Stop
16”w Z45 Horizontal Extrusion
16”w Z45 Horizontal Extrusion
18.5”w Z45 Horizontal Extrusion
Door
Hinge
Hinge
Slide pin into
hinge attached
to vertical.
Slide door
hinge over pin.
Door Attachment
*
Pin
CEI-110 Corner Connection
*
1) Insert TSRV2 and A1 Brackets
into milled groove of extrusion.
2) Slide connecting extrusion over
exposed end of brackets.
3) Use Set screws to secure
extrusions.
4) Use Set screws to secure
extrusions.
TSRV2
Bracket
A1
Screws
When assembled
Counter Top
Transformer
Shelf
shelf suppoprt
Door Stop
Door Hinge
shelf suppoprt
shelf suppoprt
shelf suppoprt
BACK SIDE
1
1A
2
5
3
6
46A
7A
7
5A
2A
+
-
Power
Female
Transformer
Light to Tranformer Attachment
SEG Graphic Installation
Corner A
Corner D
Corner B
Corner C
It is important to first insert
graphic into each alternate
corner then to the sides of
the frame. If this is not done,
graphic will not fit into the
frame correctly.
Step 1
Insert corner A. Turn edge of
graphic so silicon welt is
perpendicular to face of
graphic. Insert narrow side
of welt with fabric to outside
into the channel. Repeat for
other side of this corner.
Step 2
Repeat Step 1 for opposite
corner C, then insert corner
B, followed by corner D, to
complete the installation of
the corners.
Step 3
Once all corners are inserted,
press one silicon edge into
channel from corners and
work toward the center.
Make sure welt is fully inserted
into channel. Continue until
all sides are done. Smooth
out edges of graphic.
Graphic Removal
To remove the graphic from
the frame, locate the fabric
pull tab. Gently pull up on
the tab to remove the fabric.
B
l
o
c
k
er Infi
l
l
D
o
o
r
I
nf
i
ll
I
nf
i
ll
Maximum of 3 lights per Transformer
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17

Classic Exhibits VK-2993 Setup Instructions

Classic Exhibits
Brand
Classic Exhibits
Model
VK-2993
Type
Setup Instructions
Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

in other languages

Related papers

Other documents