WINSOON GCM3650 Installation guide

Type
Installation guide

This manual is also suitable for

Installation Manual
Barn Door Hardware
www.winsoonhardware.com
1
Track Accessories
Single Door Hardware Kit Includes
Part Name
5FT4FT
6FT 6.6FT7.5FT 8FT 9FT 11FT10FT 12FT 13FT 14FT 15FT 16FT 17FT 18FT
1
1 1 1 2 2 2 2 2
0
0 0 0 1 1 1 1 1
1
0
2
1
2
1
3
2
3
2
2 2 2
2
2 2 2 2 2 2 22 2 2 2
3
4 5 6
3
4 6 6 8 9 10
11
8 8 10 12
2
2 2 2
2
2 2 2 2 2 2 22 2 2 2
2
2 2 2
2
2 2 2 2 2 2 22 2 2 2
2
1
1 1 1
1
1 1
1
1 1 1 11 1 1
1
1
1 1 1
1
1 1
1
1 1 1 11 1 1
1
3
2
3
2
picture
Junction
Tube
Tube Plug
Spacer
Floor
guide
Door
Stopper
Hex
Wrench
Track
Hanger
Double Door Hardware Kit Includes
Part Name
5FT4FT
6FT 6.6FT7.5FT 8FT 9FT 11FT10FT 12FT 13FT 14FT 15FT 16FT 17FT 18FT
1
1 1 1 2 2 2 2 2
0
0 0 0 1 1 1 1 1
1
0
2
1
2
1
3
2
3
3
4
4
4
4 4
4
4 4
4 4
4
4 4
4
4 4
4
4
4
4 4
4
4 4
4 4
4
4 4
4
4 4
4 5 6
3
4 6 6 8 9 10
11
8 8 10 12
2
2 2 2
2
2 2 2 2 2 2 22 2 2 2
2
2 2 2
2
2 2 2 2 2 2 22 2 2 2
2
1
1 1 1
1
1 1
1
1 1 1 11 1 1
1
3
2
3
2
picture
Junction
Tube
Tube Plug
Spacer
Floor
guide
Door
Stopper
Hex
Wrench
Track
Hanger
Note: If you encounter any problem with the package and the following installa-
tion, please email us at [email protected] . Please also tell
us your “ORDER ID,” we will solve any issues for you as soon as possible.
● Installation Tools
Check the Quantities of Flat Track ,Accessories and Steel
Hanger.
Pencil Level RatchetWrenchRuler
drill
Router
Chart: Track Junction
19.7” 19.7”10.3”
10.3”
5FT
19.7” 19.7” 19.7”3.45 3.45
5.5FT
10FT
6FT
12FT
6.6FT
13FT
7.5FT
8FT
16FT
19.7” 19.7” 4.3”4.3”
4FT
15FT
17FT
18FT
2
9FT
11FT
14FT
19.7” 19.7” 19.7” 6.45”6.45”
19.7” 19.7” 19.7” 10.05”10.05”
19.7” 19.7” 19.7” 19.7” 5.6”5.6”
3
Type-a
Type-b Type-c
Hanger
Track
Spacer
Floor Guide
Door Stopper
Hex Wrench
Tube PlugJunction Tube
type-a
type-b
type-c
type-a
type-b
b-1 b-2
b-3
type-c
Tip: Different Steel Hanger styles match with different Door Stoppers. Please identify
the matching Hanger and Stopper you bought.
● Steel Hanger
Prepare Your Doors
19.7” 19.7” 4.3”4.3”
19.7” 19.7” 4.3”4.3” 19.7” 19.7” 4.3”4.3”
19.7” 19.7”10.3”
10.3”
19.7” 19.7”10.3”
10.3”
19.7” 19.7”10.3”
10.3”
19.7” 19.7”10.3”
10.3”
19.7” 19.7”10.3”
10.3”
19.7” 19.7”10.3”
10.3”
19.7” 19.7” 4.3”4.3”
19.7” 19.7”10.3”
10.3”
19.7” 19.7” 19.7”3.45 3.45
19.7”
19.7” 19.7”
3.45
3.45
19.7” 19.7” 19.7” 6.45”6.45”
19.7” 19.7” 19.7” 6.45”6.45”
19.7” 19.7” 19.7” 6.45”6.45”
19.7” 19.7” 19.7” 6.45”6.45”
19.7” 19.7” 19.7” 6.45”6.45”
19.7” 19.7”10.3”
10.3”
19.7” 19.7” 19.7” 6.45”6.45”
19.7” 19.7” 19.7” 6.45”6.45” 19.7” 19.7” 19.7” 6.45”6.45”
19.7” 19.7” 19.7” 10.05”10.05” 19.7” 19.7” 19.7” 10.05”10.05”
19.7” 19.7” 19.7” 19.7” 5.6”5.6” 19.7” 19.7” 19.7” 19.7” 5.6”5.6”
※Hardware Installation
54
2-1/4”
(57mm)
2”
(50mm)
Type-a
Type-a
Type-b
Type-b
Type-c
Type-c
3-5/16”(84mm)
2-1/4”(57mm)
2-15/16”(74.50mm)
1/4”(6mm)
5-1/8”(130.75mm)
2-1/8”(54mm)
2-1/8”(54mm)
7/16”(12mm)
7/16”(12mm)
7/16”(12mm)
2-1/8”(54mm)
2-1/8”(54mm)
5/16”(8mm)
5/16”(8mm)
5/16”(8mm)
3-5/16”(83mm)
3-7/8”(98mm)
5/8”(16mm)
1-1/8”(30mm)
1-1/8”(30mm)
1-1/8”(30mm)
2-3/4”(70mm)
2-1/4”(58mm)
2-3/16”(55.31mm)
2-3/4”(70mm)
2”(50mm)
2”(50mm)
Step 1: Attach Steel Hangers to Your Doors
Drill 3/8” (10mm) holes at the position from the top of the
doors shown in the above chart.
2”
(50mm)
b-2
b-3
76
3/4”(20mm)
5/16”(7mm)
Step 2: Cut Floor Guide Slot At The Bottom Of The Door
Cut a 5/16” (7mm) wide, 3/4” (20mm) deep slot at the
bottom of the door.
Recommended: Cut the slot with a router and slot cutter bit.
Step 3: Connect Tracks
Connect your tracks with junction tube if needed.
Step 4: Install Spacers
a.Putting the b-3 into the rail and make the hole direction
of b-3, rail and b-2 is consistent.
b.Installing in order from inside to outside to prevent
missing the hole.
Step 5:Draw Line for the Track
Using a level, draw a line for the Track, at the 2-5/16 (58mm)
+door height + 3/8” (10mm) above the floor.
Prepare and Install the Tracks
door height + 2-11/16” (68mm)
2-5/16”
(58mm)
b-1
18.59”
1.1”
18.59”
1.1”
18.59”
1.1”
1.1”
1.1in
b-1
b-2
Anti jump
device
8 9
1-3/32”(28mm)
Step 6:Mark and Drill Track Holes
1.Mark the positions of each set’s two spacer holes, the
distance between each hole is shown as the picture.
2.Punch all the marked positions into the wall with impact
drill, put the expansion pipes into the holes created, then punch the
pipe pins into the wall until the expansion pipes expand at their ends,
screw b - 1 into the expansion pipe.
Step 7:Install The Track
1.Overlapping b - 1 and b - 2 and tighten to fix the rails to
the wall.
2.Now you have installed the track on the wall successfully.
Hanging and Positioning Doors
Step 8: Install Your Doors
a.Hang your Steel Hangers on the Track, and then adjust
the anti-jump bar up or down so that it could make the roller clamp
the track.
b.Position doors in your desired closed and open position
and adjust Door Stoppers.
door height + 2-11/16” (68mm)
door height + 2-11/16” (68mm)
10
Usage Statement:
Use of excessive force when opening, and closing,the door(s) may result in damage to the
hardware. Always hold the handle and gently open and close the door(s).
• Failure to wear proper safety gear (i.e.,eye protection) may result in serious injury or
death. Always wear proper safety gear before using power tools.
• Improper operation of power tools may result in loss of control, serious injury or death.
Always ensure you have complete control of the power tool and the work area is free of
hazards before operatiog a power tool.
• Lack of secure clamping of the door may result in unexpected movement of the
door,loss of power tool control and serious injury or death. Always securely clamp the door
in place before cutting,or drilling, the door.
• Lack of ,or improperly installed Anti-jump Disc may result in the door coming off the
track and cause serious injury or death. installation of Anti-jump Disks are required for safe
operation of this hardware. installed properly, these discs will keep the door securely
attached to the teack.
WARNING
• Mishandling of heavy objects (i.e.,doors) may cause a loss of balance and serious
injury. Always be sure you have a secure hold on the object and are balanced before
moving the object.Always wear safety shoes when lifting heavy objects.
• Getting body parts (i.e., hair,fingers) caught in moving parts may cause pinching and
serious injury.Do not put fingers in parts that may move and always remove or contain
anything on your body that may become entangled with a moving part.
• Closing sliding doors with your hand on the end of the door may result in your hand, or
fingers, getting caught between the door and other solid objects (i.e., another door,
molding) causing serious injury. Always use the door handle to close doors.
CAUTION
5 year straight unconditional warranty service enables every single hardware’s durability
coverage during its life time.
Warranty Statement:
Step 9:Install the Floor Guide
Position the door at your desired close position, put half of
the floor guide under the door, mark the location, and then fix guide
to the floor.
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6

WINSOON GCM3650 Installation guide

Type
Installation guide
This manual is also suitable for

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI