www.winsoonhardware.com
Installation Manual
• Failure to wear proper safety gear (i.e.,eye protection) may result in serious
injury or death. Always wear proper safety gear before using power tools.
• Improper operation of power tools may result in loss of control, serious injury or
death. Always ensure you have complete control of the power tool and the work
area is free of hazards before operatiog a power tool.
• Lack of secure clamping of the door may result in unexpected movement of the
door,loss of power tool control and serious injury or death. Always securely clamp
the door in place before cutting,or drilling, the door.
• Lack of ,or improperly installed Anti-jump Disc may result in the door coming
off the track and cause serious injury or death. installation of Anti-jump Disks are
required for safe operation of this hardware. installed properly, these discs will keep
the door securely attached to the teack.
WARNING
• Mishandling of heavy objects (i.e.,doors) may cause a loss of balance and serious
injury. Always be sure you have a secure hold on the object and are balanced before
moving the object.Always wear safety shoes when lifting heavy objects.
• Getting body parts (i.e., hair,fingers) caught in moving parts may cause pinching
and serious injury.Do not put fingers in parts that may move and always remove or
contain anything on your body that may become entangled with a moving part.
• Closing sliding doors with your hand on the end of the door may result in your
hand, or fingers, getting caught between the door and other solid objects (i.e.,
another door, molding) causing serious injury. Always use the door handle to close
doors.
CAUTION
Usage Statement:
Use of excessive force when opening, and closing,the door(s) may result in damage to the
hardware. Always hold the handle and gently open and close the door(s).
5 year straight unconditional warranty service enables every single hardware’s durability
coverage during its life time.
Warranty Statement:
1
www.winsoonhardware.com
6
www.winsoonhardware.com
Junction Tube
Tube Plug
Single door hardware kit includes
Part Name
Hanger
Track
Spacer
Floor guide
Door Stopper
Hex Wrench
picture 5FT 6FT 6.6FT 7.5FT 8FT 10FT 12FT 13FT 15FT 16FT
2 2 2 2 2 2 2 2 2 2
2 2 2 2 2 2 2 2 2 2
2 2 2 2 2 2 2 2 2 2
1 1 1 1 1 1 1 1 1 1
1 1 1 1 1 1 1 1 1 1
0 0 0 0 0 1 1 1 1 2
1 1 1 1 1 2 2 2 2 3
3 4 4 5 5 6 8 8 10 10
Junction Tube
Tube Plug
Double door hardware kit includes
Part Name
Hanger
Track
Spacer
Floor guide
Door Stopper
Hex Wrench
picture 5FT 6FT 6.6FT 7.5FT 8FT 10FT 12FT 13FT 15FT 16FT
4 4 4 4 4 4 4 4 4 4
4 4 4 4 4 4 4 4 4 4
2 2 2 2 2 2 2 2 2 2
2 2 2 2 2 2 2 2 2 2
1 1 1 1 1 1 1 1 1 1
0 0 0 0 0 1 1 1 1 2
1 1 1 1 1 2 2 2 2 3
3 4 4 5 5 6 8 8 10 10
84mm/3.31in
74.50mm/2.93in
6mm/0.24in
130.75mm/5.14in
54mm/2.13in
12mm/0.47in
12mm/0.47in
54mm/2.13in
8mm/0.32in
8mm/0.32in
83mm/3.27in
54mm/2.13in
54mm/2.13in
8mm/0.32in
98mm/3.86in
16mm/0.63in
30mm/1.18in
30mm/1.18in
30mm/1.18in
70mm/2.76in
58mm/2.28in
55.31mm/2.17in
12mm/0.48in
57mm/2.25in
70mm/2.761in
50mm/1.97in
50mm/1.97in
Hanger
Track
Spacer
Floor Guide
Door Stopper
Hex WrenchTube Plug
Junction Tube
type-a
type-b
type-c
type-a
type-b
type-c
Note: Different hangers match with different door stoppers
type-a type-b type-c
5
www.winsoonhardware.com
www.winsoonhardware.com
2
b-2
b-3
Door
Height
2.28”/58 mm
9/32”
0.4”/10mm
3/8”
Step-a
Step-b
Step-c
1Putting the b-3 into the rail and make the hole
direction of b-3, rail and b-2 is consistent.
2. Installing in order from inside to outside to
prevent missing the hole
1.Mark the positions of each set’s two spacer
holes, the distance between each hole is shown
as the picture.
2.Punch all the marked positions into the wall
with impact drill, put the expansion pipes into
the holes created, then punch the pipe pins into
the wall until the expansion pipes expand at
their ends, screw b - 1 into the expansion pipe.
1. Draw down a horizontal line which is [2-5/16
(58mm) + Door Height + 3/8”(10mm)] above
the floor. The length of the line needs to be the
same as your total track length.
2. The horizontal line is to label out the track’s
center line, and mark down each track holes’
center point to attach the track later.
b-1
b-1
b-2
b-3
18.59in
18.59in
18.59in
1.1in
1.1in
1.1in
1.1in
1-1/9”
28mm/1.1in
First Hole
19.7” 19.7” 10.3”10.3”
5FT
19.7” 19.7” 10.3”10.3”
19.7” 19.7” 10.3”10.3”
16FT
19.7” 19.7” 19.7” 6.45”6.45”
19.7” 19.7” 19.7” 6.45”6.45”
6FT
19.7” 19.7” 19.7” 10.05”10.05”
6.6FT
19.7” 19.7” 19.7” 19.7” 5.6”5.6”
7.5FT
19.7” 19.7” 19.7” 19.7” 5.6”5.6” 19.7” 19.7” 19.7” 19.7” 5.6”5.6”
15FT
19.7” 19.7” 19.7” 19.7” 8.6”8.6”
8FT
10FT
19.7” 19.7” 10.3”10.3” 19.7” 19.7” 10.3”10.3”
12FT
19.7” 19.7” 19.7” 6.45”6.45” 19.7” 19.7” 19.7” 6.45”6.45”
13FT
19.7” 19.7” 19.7” 10.05”10.05” 19.7” 19.7” 19.7” 10.05”10.05”
3 4
www.winsoonhardware.com www.winsoonhardware.com
Step-e
Step-f
Step-d
57mm/2.25”
1/4’’
B-1
B-2
1. Overlapping b - 1 and b - 2 and tighten to
fix the rails to the wall
2. Now you have installed the track on the wall
successfully.
1. Position the wheels above the door and
locate them, marking the location of the hole
and punch the hole.
2.Screwing the expansion pipe into the drilled
hole, put on the wheel, and use the screw fix
the wheels to the door
1. Open a slot ( 0.79”/20mm wide,0.79”/20mm
deep ) at the bottom of the door with a
chainsaw. It will be used for installing the floor
guide.
Step-g
Step-h
1. Slide your door to the resting position
shown in the picture. Use your level to
plumb your door to the floor.
2. When the door is in the opening
position, place the floor guide half way
into the door slot under the door.
3. Double check to make sure your door
is plumb to the floor again. Hold the floor
guide firmly in position and mark the two
center points of the two floor guide holes.
Then put your floor guide off the position.
4. Use a
1/4”
(6mm) drill bit to drill 2 holes
on the floor at the center points you have
marked. Put the two plastic expansion
nails into both of the drilled holes on the
floor.
5. Then hold the floor guide firmly at
where to match the floor guide holes to
the floor holes, drill in the floor guide
screws to secure your floor guide to the
floor using a phillips bit.
6. Repeat Step-h-1 to Step-h-5 on the
other door for a double door installation.
7. Now your sliding barn door has been
installed completely.
1. Put the door on the track, adjust the
distance of the Anti jump device to avoid
the door falling off the track.
2. Adjusting the position of the stopper
and fix it with a hex wrench.
3. press the plug on.
Anti jump
device
/
