Kichler Lighting 52233BK User manual

Brand: Kichler Lighting

Model: 52233BK

Type: User manual

Kichler Lighting 52233BK is a versatile lighting fixture that can be mounted on a rigid stem or with a loop and chain link. It features a classic design with a metal frame and a glass shade, making it suitable for a variety of décor styles. The fixture is compatible with incandescent, LED, or CFL bulbs, giving you the flexibility to choose the light output and energy efficiency that best suits your needs. With its adjustable mounting options and easy installation process, the Kichler Lighting 52233BK is a great choice for updating the lighting in any room of your home.

IS-52233-US

We’re here to help 866-558-5706

Hrs: M-F 9am to 5pm EST

13) Grounding instrucons: (See Illus. a or b).

a) On xtures where mounng strap is provided with a

hole and two raised dimples, wrap ground wire from

outlet box around green ground screw, and thread into

hole.

b) On xtures where a cupped washer is provided,aach

ground wire from outlet box under cupped washer and

green ground screw, then thread into mounng strap.

If xture is provided with ground wire, connect xture

ground wire to outlet box ground wire with wire connector

aer following the above steps. Never connect ground wire

to black or white power supply wires.

14) Make wire connecon. Reference chart below for correct

connecons and wire accordingly.

Connect Black or Red

Supply Wire to:

Connect White Supply

Wire to:

Black White

*Parallel cord (round &

smooth)

*Parallel cord (square &

ridged)

Clear, Brown, Gold or

Black without Tracer

Clear, Brown, Gold or Black

with Tracer

Insulated wire (other

than green) with copper

conductor

Insulated wire (other

than green) with silver

conductor

*Note: When parallel wire (SPT

1 & SPT 2) are used. The neutral

wire is square shaped or ridged

and the other wire will be round

in shape or smooth

(see illus.)

Neutral Wire

15) Push xture to ceiling, carefully passing mounng screws

through holes in canopy.

NOTE: Be certain wires do not get pinched between

mounng strap and canopy, or canopy and ceiling.

16) Use knobs[K] and lockwashers[J] to secure canopy.

Tighten to secure.

17) Carefully lower glass shade[P] onto the xture. Slip the

smaller opening over the socket[Q] unl seated on the

socket.

18) Secure glass to socket by screwing socket ring[S] onto

threads on outside of socket.

19) Insert recommended bulbs. (Not supplied).

GREEN GROUND

SCREW

CUPPED

WASHER

OUTLET BOX

GROUND

FIXTURE

GROUND

DIMPLES

WIRE CONNECTOR

OUTLET BOX

GROUND

GREEN GROUND

SCREW

FIXTURE

GROUND

Fixture Diagram

Parts List

Cauons

CAUTION – RISK OF SHOCK –

Disconnect Power at the main circuit breaker panel or main fusebox before starng and during

the installaon.

WARNING:

This xture is intended for installaon in accordance with the Naonal Electrical Code (NEC) and all

local code specicaons. If you are not familiar with code requirements, installaon by a cered

electrician is recommended.

CLEANING:

• Always be certain that electric current is turned o before cleaning.

• Only a so damp cloth should be used. Harsh cleaning products may damage the nish.

Installaon Instrucons

[A] Stems

[B] Short Threaded Tubes

[C] Outlet Box

[D] Mounting Screws

[E] Lockwasher

[F] Hexnut

[G] Mounting Strap

[H] Canopy

[I] Strap Mounting Screws

[J] Lockwashers

[K] Knobs

[L] Second Loop

[M] Chain Link

[N] Tubes

[O] Frame

[P] Glass Shade

[Q] Socket

[R] First Loop

[S] Socket Ring

[T] Ground Wire Loop

RIGID STEM MOUNT

1) Screw tubes[N] into couplings on frame[O].

2) On side of xture with xture wires, Pass xture wires through stems[A] and short threaded

tubes[B]. Screw stems[A] together using short threaded tubes[B].

3) On opposite side of xture (without xture wires) screw a second set of stems together using

short threaded tubes (same number of stems and short threaded tubes from previous step but

without xture wire).

NOTE: Thread locking compound must be applied to all stem threads as noted with symbol (4)

to prevent accidental rotaon of xture during cleaning, relamping, etc.

4) Screw rst stem of connected set of stems into tube[N]. Repeat for second set of connected

stems.

5) On side of xture with xture wires, pass xture wires through one short threaded tube[B].

Screw short threaded tube onto top of stem.

6) On opposite side of xture (without xture wires), screw one short threaded tube onto top of

stem.

7) Pass xture wires through hole in canopy[H]. Lower canopy down towards stems. Pass holes in

canopy over ends of short threaded tubes on top of the stems.

8) On side of xture with xture wires, pass xture wires through lockwasher[E]. Place

lockwasher onto end of short threaded tube protruding from inside canopy.

9) Pass xture wires through hexnut[F]. Thread hexnut onto end of short threaded tube.

NOTE: Fixture wires should not be cut shorter than 20 inches from above the canopy.

10) On opposite side of xture (without xture wires), place loop of ground wire[T] over short

threaded tube protruding from inside of canopy and secure into place with a lock washer and

hexnut as shown.

11) Find the appropriate threaded holes on mounng strap[G]. Assemble mounng screws[D] into

threaded holes.

12) Aach mounng strap to outlet box[C] using the strap mounng screws[I]. Mounng strap can

be adjusted to suit posion of xture.

Installaon Instrucons (connued)

LOOP / CHAIN LINK MOUNT

1) Follow steps 1 - 4 from “Rigid Stem Mount” Instrucons.

2) Thread one short threaded tube[B] into end of each small

loop[R, L].

3) On side of xture with xture wires, pass xture wires

through rst loop[R]. Thread rst loop onto end of last stem.

4) Pass xture wires through second loop[L] and through hole

in canopy[H]. Pass short threaded tube at end of second loop

through hole in canopy.

5) Pass xture wires through lockwasher[E]. Place lockwasher

onto end of short threaded tube protruding from inside

canopy.

6) Pass xture wires through hexnut[F]. Thread hexnut onto

end of short threaded tube.

NOTE: Fixture wires should not be cut shorter than 20

inches from above the canopy.

7) On opposite side of xture (without xture wires), Thread

rst loop[R] onto end of last stem. Pass threaded pipe at end

of second loop[L] through hole in canopy.

8) Place loop of ground wire[T] over short threaded tube

protruding from inside of canopy and secure into place with a

lock washer and hexnut as shown.

9) Aach open chain link[M] to small loops at end of each stem

and to small loops on canopy and close the open chain link by

placing a piece of cloth over the open link and using a pair of

pliers gently squeeze the link closed.

10) Follow steps 11 - 19 from “Rigid Stem Mount” Instrucons.

►

Page is loading ...

Kichler Lighting 52233BK User manual

Brand: Kichler Lighting

Model: 52233BK

Type: User manual

Download PDF

report

in other languages

français: Kichler Lighting 52233BK Manuel utilisateur
español: Kichler Lighting 52233BK Manual de usuario

Kichler Lighting 52233BK User manual

Kichler Lighting 52233BK User manual

in other languages

Related papers

Other documents