IS-52091-US
We’re here to help 866-558-5706
Hrs: M-F 9am to 5pm EST
14) Grounding instrucons: (See Illus. a or b).
a) On xtures where mounng strap is provided with a hole and two raised
dimples, wrap ground wire from outlet box around green ground screw,
and thread into hole.
b) On xtures where a cupped washer is provided,aach ground wire from
outlet box under cupped washer and green ground screw, then thread
into mounng strap.
If xture is provided with ground wire, connect xture ground wire to outlet
box ground wire with wire connector aer following the above steps. Never
connect ground wire to black or white power supply wires.
15) Make wire connecon. Reference chart below for correct connecons and
wire accordingly.
Connect Black or Red
Supply Wire to:
Connect White Supply
Wire to:
Black White
*Parallel cord (round &
smooth)
*Parallel cord (square &
ridged)
Clear, Brown, Gold or
Black without Tracer
Clear, Brown, Gold or Black
with Tracer
Insulated wire (other
than green) with copper
conductor
Insulated wire (other
than green) with silver
conductor
*Note: When parallel wire (SPT
1 & SPT 2) are used. The neutral
wire is square shaped or ridged
and the other wire will be round
in shape or smooth
(see illus.)
Neutral Wire
16) Push xture to ceiling, carefully passing threaded pipe through hole in
canopy[H].
NOTE: Be certain wires do not get pinched between mounng strap and
canopy, or canopy and ceiling.
17) Secure xture to ceiling with lock-up knob[N].
18) Insert recommended bulbs. (Not supplied).
GREEN GROUND
SCREW
CUPPED
WASHER
OUTLET BOX
GROUND
FIXTURE
GROUND
DIMPLES
WIRE CONNECTOR
OUTLET BOX
GROUND
GREEN GROUND
SCREW
FIXTURE
GROUND
a
b
Fixture Diagram
Parts List
Cauons
CAUTION – RISK OF SHOCK –
Disconnect Power at the main circuit breaker panel or main fusebox before
starng and during the installaon.
WARNING:
This xture is intended for installaon in accordance with the Naonal Electrical
Code (NEC) and all local code specicaons. If you are not familiar with code
requirements, installaon by a cered electrician is recommended.
CLEANING:
• Always be certain that electric current is turned o before cleaning.
• Only a so damp cloth should be used. Harsh cleaning products may damage
the nish.
Installaon Instrucons
[A] Stems
[B] Short Threaded
Tubes
[C] Outlet Box
[D] Safety Cable
[E] Lockwasher
[F] Hexnut
[G] Mounting Strap
[H] Canopy
[I] Strap Mounting
Screws
[J] Threaded Pipe
[K] Hexnut
[L] Second Loop
[M] Chain Link
[N] Lock-up Knob
[O] Fixture Body
[P] Ground Wire Loop
[Q] First Loop
RIGID STEM MOUNT
1) On side of xture with xture wires, Pass xture wires through stems[A] and
short threaded tubes[B]. Screw stems together using short threaded tubes
and screw stems into coupling on xture body[O] using a short threaded
tube.
2) On opposite side of xture (without xture wires) screw a second set of
stems together using short threaded tubes (same number of stems and short
threaded tubes from previous step but without xture wire) and screw stems
into opposite coupling on xture body using a short threaded tube.
NOTE: Thread locking compound must be applied to all stem threads as
noted with symbol (4) to prevent accidental rotaon of xture during
cleaning, relamping, etc.
3) On side of xture with xture wires, pass xture wires through one short
threaded tube[B]. Screw short threaded tube onto top of stem.
4) On opposite side of xture (without xture wires), screw one short threaded
tube onto top of stem.
5) Pass xture wires through hole in canopy[H]. Lower canopy down towards
stems. Pass holes in canopy over ends of short threaded tubes on top of the
stems.
6) On side of xture with xture wires, pass xture wires through loop of
safety cable[D]. Slip loop of safety cable over end of short threaded tube
protruding from inside of canopy.
7) Pass xture wires through lockwasher[E]. Place lockwasher onto end of
short threaded tube protruding from inside canopy.
8) Pass xture wires through hexnut[F]. Thread hexnut onto end of short
threaded tube.
NOTE: Fixture wires should not be cut shorter than 20 inches from above the
canopy.
9) On opposite side of xture (without xture wires), place loop of ground
wire[P] over short threaded tube protruding from inside of canopy and
secure into place with a lock washer and hexnut as shown.
10) Take threaded pipe[J] from parts bag and screw in mounng strap[G] a
minimum of 6 mm (1/4”). Lock into place with hexnut[K].
11) Run another hexnut down threaded pipe almost touching rst hexnut.
Mounng strap must be posioned with extruded thread faced into outlet
box[C]. Threaded pipe must protrude out the back of mounng strap. Screw
third hexnut onto end of threaded pipe protruding from back of mounng
strap.
12) Aach mounng strap to outlet box[C] using the strap mounng screws[I].
Mounng strap can be adjusted to suit posion of xture.
13) Aach safety cable to the mounng strap by looping over the strap and
secure into place to prevent damage to the wires during wiring.
Installaon Instrucons (connued)
LOOP / CHAIN LINK MOUNT
1) Follow steps 1 and 2 from “Rigid Stem Mount” Instrucons.
2) Thread one short threaded tube[B] into end of each small loop[Q, L].
3) On side of xture with xture wires, pass xture wires through rst loop[Q].
Thread rst loop onto end of last stem.
4) Pass xture wires through second loop[L] and through hole in canopy[H]. Pass
short threaded tube at end of second loop through hole in canopy.
5) Pass xture wires through loop of safety cable[D]. Slip loop of safety cable over
end of short threaded tube protruding from inside of canopy.
6) Pass xture wires through lockwasher[E]. Place lockwasher onto end of short
threaded tube protruding from inside canopy.
7) Pass xture wires through hexnut[F]. Thread hexnut onto end of short threaded
tube.
NOTE: Fixture wires should not be cut shorter than 20 inches from above the
canopy.
8) On opposite side of xture (without xture wires), Thread rst loop[Q] onto
end of last stem. Pass threaded pipe at end of second loop[L] through hole in
canopy.
9) Place loop of ground wire[P] over short threaded tube protruding from inside of
canopy and secure into place with a lock washer and hexnut as shown.
10) Aach open chain link[M] to small loops at end of each stem and to small loops
on canopy and close the open chain link by placing a piece of cloth over the
open link and using a pair of pliers gently squeeze the link closed.
11) Follow steps 10 - 18 from “Rigid Stem Mount” Instrucons.
►
►
►
►
►
A
M
Q
B
B
►
N
P
D
F
E
H
C
G
I
J
K
O
B
L
F
E
M
L
Q
Page is loading ...
Page is loading ...
-
1
-
2
-
3
Ask a question and I''ll find the answer in the document
Finding information in a document is now easier with AI
in other languages
Related papers
-
Kichler Lighting 52263OZ User manual
-
Kichler Lighting 52037CLP User manual
-
Kichler Lighting 52054CG User manual
-
Kichler Lighting 52140BK User manual
-
Kichler Lighting 49309BK User manual
-
Kichler Lighting 52033BK User manual
-
Kichler Lighting 52233BK User manual
-
Kichler Lighting 52224FXG User manual
-
Kichler Lighting 52123BNB User manual
-
Kichler Lighting 52273BK User manual
Other documents
-
Kichler 52263OZ Operating instructions
-
-
-
-
-
-
-
-
-