Evolveo salvarix kamery User manual

Category
Security camera accessories
Type
User manual
Salvarix
This manual is for installing and controlling Salvarix cameras
CAM OT1080P03C
CAM IN720P316
CAM IN720P312
www.evolveo.com
Installation and controlling manual of EVOLVEO Salvarix Cameras
Suitable for part.no: CAM OT1080P03C, CAM IN720P316, CAM IN720P312
You can manage cameras by EVOLVEO Salvarix application as full alarm
solution or by Yoosee application suitable for cameras only.
Cameras CAM IN720P312 and CAM IN720P316 are suitable for indoor use
only.
Camera CAM OT1080P03C can be used for indoor and outdoor use. Not
recommend to install camera in area where can be impact of heavy rain.
Ensure that LAN and power cables are safely protected against moisture e.g.
in installation box with protection at least IP44.
Cameras support MicroSD cards. Use hi-speed type with write speed at least
Class 10.
Use original accessories to install the cameras.
Login and registration
In EVOLVEO Salvarix application enter to “cameramenu.
Sign in to your account or create a new one.
After signing in, you can add a security camera. Press the “+” button and
select “Smartlink”.
Select a connection method.
1) WiFi
Make sure you are connected to WiFi
Make sure 5G WiFi is not used - not supported
Enter the network access password
Press "next"
Plug in the camera and wait for initialization
After successful initialization, the camera will emit an acoustic signal
at short intervals
Press "listen to tone"
Adjust the media volume on your device and press "next"
The phone starts broadcasting the configuration sound recording,
move the phone closer to the camera.
After pairing, set the name and enter the camera password
2) LAN
Connect the camera to the power and connect to the LAN
Wait about 1 minute for the camera to initialize
Connect to the same network with your phone
Select "Use cable connection" in the app
In the list of devices you will see the connected camera, select the
camera and press the "+"
Enter the device name and camera password
Change the factory password to more secure. We recommend a
combination of uppercase and lowercase letters, numbers, and
special characters to ensure safe operation.
1. Status
2. Weak password
3. Activation, deactivation of guarding
4. Playback, recording
5. Settings
1
2 3 4 5
Live Image Control
6. Date
7. Position
8. Save position
9. Quality settings
10. Guarding
11. Speaker
12. Microphone
13. Save the image
6
7
8
9
10 11 12 13
In the settings menu you can set all the camera parameters:
Device information (SW version, FW, camera name)
Set the camera date and time
Adjust video format, volume, image rotation
Set password for administrator and guest
Connection settings
Alarm settings, email notification settings, motion detection settings
Schedule video recording settings
Set up wireless peripherals and assign wireless sensors
Updating the FW camera
FAQ:
Can't connect to WiFi
Check if you are connecting to a 2.4GHz network
Reset the camera by pressing the reset button for about 4 seconds
and then try again
Check the WiFi signal quality, keep the camera as close as possible to
the router when pairing
CAM OT1080P03C check the WiFi antenna connector
CAM IN720P316 check the WiFi antenna connector, or install an
external antenna for better reception of the WiFi signal
The camera is not recording
Check the status and functionality of the MicroSD card
Check the recording settings
Camera doesn't work
Check that the adapter and LAN connector are connected correctly
The camera is off-line
Check the Internet status at the camera location
Unplug the camera and reconnect it
Do you still need an advice after reading this guide?
First read “Frequently Asked Questions” at www.evolveo.com or contact the
EVOLVEO technical support.
The warranty DOESN´T APPLY to:
Using the device for other purposes than it was designed to
installation of another firmware then the one that was installed as
the original from the factory or that is to be downloaded at
ftp://ftp.evolveo.com
mechanical damage of caused by inappropriate using
damage caused by the natural elements as fire, water, static
electricity, overvoltage and so on damage caused by unauthorized
repair
damage of the guarantee seal or unreadable serial number of the
device
Disposal: The symbol of crossed out container on the product, in the
literature or on the wrapping means that in the European Union all the
electric and electronic products, batteries and accumulators must be placed
into the separate salvage after finishing their lifetime. Do not throw these
products into the unsorted municipal waste
DECLARATION OF CONFORMITY
Hereby, the company Abacus Electric, s.r.o. declares that the EVOLVEO CAM
OT1080P03C, CAM IN720P316, CAM IN720P312 are in compliance with the
requirements of the standards and regulations, relevant for the given type of
device.
Find the complete text of Declaration of Conformity at
ftp://ftp.evolveo.com/ce
Dovozce / Dovozca / Importer / Importőr
Abacus Electric, s.r.o.
Planá 2, 370 01, Czech Republic
Výrobce / Výrobca / Manufacturer / Gyártó
Naxya Limited
No. 5, 17/F Bonham Trade Centre, 50 Bonham Strand,
Sheung Wan, Hong Kong
Copyright © Abacus Electric, s.r.o.
www.evolveo.com
www.facebook.com/EvolveoCZ
All rights reserved.
Design and specification may be changed without prior notice.
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14

Evolveo salvarix kamery User manual

Category
Security camera accessories
Type
User manual

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI