1 / 38
LVS600
seamless switcher
User manual
2 / 38
c o n t e n t s
Chapter1. Safety precautions -----------------------------------------------3－3
Chapter2. Items list -------------------------------------------------------------4－4
Chapter3. Hardware connection
3-2 Rear view -------------------------------------------------------------------5－5
3-3 Port description-------------------------------------------------------------5－6
3-4 Connection diagram--------------------------------------------------------7－7
3-5 Specification ---------------------------------------------------------------6－7
3-6 Dimension ---------------------------------------------------------------7－7
Chapter4. Front panel
4-1 Button instruction ---------------------------------------------------------8－9
Chapter5. Basic operation introduction
5-1 Select input signals for input cards-----------------------------------------10－10
5-2 PIP setup of input cards-------------------------------------------------------10－10
5-3 Switch output ports signals---------------------------------------------------10－10
5-4 Setting output ports switching effects--------------------------------------10－10
5-5 Setting output cards to preview mode---------------------------------------10－11
5-6 Brightness setup----------------------------------------------------------------11－11
5-7 Automatic VGA calibration ----------------------------------------------11－12
5-8 Button lock--- ------------------------------------------------------------------12－12
5-9 Check system information ------------------------------------------------12－13
Chapter6. User settings
6-1 Input cards setup-----------------------------------------------------12－18
6-2 Output cards setup --------------------------------------------------------19－24
6-3 System setup -----------------------------------------------------------------24－33
Chapter7. Copyright information ---------------------------------------33－33
3 / 38
Chapter1. Safety precautions
! Danger
There is high voltage in the processor, to prevent any unexpected hazard,
unless you are a maintenance personnel, please do not open the cover of
the device.
! Warning
1. This device shall not encounter water sprinkle or splash, please do not
place anything containing water on this device.
2. To prevent fire, keep this device far from any fire source.
3. If this device gives out any strange noise, smoke or smell, please
immediately unplug the power cord from receptacle, and contact local
dealer.
4. Please do not plug or unplug DVI signal cable if the device is
powered on.
! Caution
1．Please thoroughly read this manual before using this device, and keep
it well for future reference.
2．In the event of lighting or when you are not going to use the device for
a long time, please pull the power plug out of receptacle.
3．Nobody other than professional technicians can operate the device,
unless they have been appropriately trained or under guidance of
technicians.
4．To prevent equipment damage or electric shock, please don’t fill in
anything in the vent of the device.
5．Do not place the device near any water source or anywhere damp.
6．Do not place the device near any radiator or anywhere under high
temperature.
7．To prevent rupture or damage of power cords, please handle and keep
them properly.
8．Please immediately unplug power cord and have the device repaired,
when
1) Liquid splashes to the device.
4 / 38
2) The device is dropped down or cabinet is damaged.
3) Obvious malpractice is found or performance degrades.
Chapter2. Items list
Please unpack the product with care, and then check whether all the following
items are included in the package. If anything is found missing, please contact
the dealer.
Standard accessories
The accessories supplied with this product may differ from the following
pictures, but they are applicable for the regions where you live.
1.5m power cable*1
1.5m DVI cable*1
0.5m DVI Cable
(Quantity depends
on output cards)
VGA to
VGA+RCA*6
1.5m
RS232-RJ45*1
0.2M network
cable*1
1.5m USB cable*1
HDMI to DVI-D
convert *2
DVI-I to VGA
convet*1
5 / 38
Operation manual
*1
Operation CD*1
Chapter3. Hardware connection
3-1 System framework introduction
Due to the plug-in design of input and output cards, the LVS600
configuration will depend on customer-specific requirements.
注
意
：
如
果
插
2
Notice: when 2 output cards are plugged in, one of them can be used
for preview output.
3-2 Rear view
Card model
Types of cards
number
Function
In_A、In_B
In_C、In_D
In_E、In_F
Full HD video
cards
*6
Integrate multiple video
signals of different
types and formats
Out-K、Out-L
Output cards
*2
Output processed
signals to each display
unit
6 / 38
NO.
Introduction
1
Full HD video input card In-A
2
Full HD video input card In-B
3
Full HD video input card In-C
4
Full HD video input card In-D
5
Full HD video input card In-E
6
Full HD video input card In-F
7
Output card Out-K
8
Output card Out-L
9
Communication port
3-3 Ports description
1) video input signals
LVS600 maximally supports 6pcs FULL HD video input cards.
Full HD video input card supports 4 video signals input. The port
description is as follows：
Port
description
VGA/Video
1* VGA(PC analog signal)
1*Composite(PAL/NTSC,VGA—VGA-RCA
adapter needed)
DVI
1 X DVI (HDMI1.3 compatible)
SDI
1x SDI/HD-SDI/3G-SDI digital signal input.
2) Video output signals
LVS600 maximally supports 2 PCS of output cards (Out-K, Out-L)
and each card supports 3 DVI outputs and 1 VGA output. The port
description is as follows:
Port
Description
Out1-Out3
Out4-Out6
3 DVI outputs for connecting to sending
cards or monitors
DVI-I
Compatible with both DVI and VGA
1
2
3
4
5
6
7
8
9
7 / 38
signals output. VGA can be used for
preview by DVI-I to VGA convert output.
3) Communication ports
Port
Description
LAN
LAN TCP/IP network control
USB
USB communication port
RS232 IN
Serial communication port, RS232
electric level, connect the RS232
interface of PC, use PC software to
control processor
RS232 Out
Serial communication looping out, RS232
electric level, use one PC to control all
processors
3-4 Connection diagram
8 / 38
3-5 Specifications
Inputs
Number/Type
6xVideo
6xVGA（RGBHV）
6xDVI（HDMI-1.3）
6xSDI（SDI/HD-SDI/3G-SDI）
Video standard
PAL/NTSC
Composite Video
Amplitude/Impedance
1V（p_p）/ 75Ω
VGA format
PC（VESA standard）
≤1920x1200_60Hz
VGA
Amplitude/Impedance
R、G、B = 0.7 V（p_p）/ 75Ω
DVI format
PC（VESA standard）
≤1920x1200_60Hz
HDMI-1.3（CEA-861）
≤1920x1080p_60Hz
SDI format
SMPTE259M-C
SMPTE 292M
SMPTE 274M/296M
SMPTE 424M/425M
480i_60Hz
576i_50Hz
720p、1080i、1080p
Input connectors
Video：4th pin of VGA
VGA：15pin D_Sub(female)
9 / 38
3-6 Dimension
DVI：24+1 DVI_D
SDI：BNC/ 75Ω
Outputs
Number /type
6xDVI
Preview output
1xDVI-I
DVI resolution
1024x768_60Hz 1280x1024_60Hz
1920x1080p_60Hz 1920x1200_60Hz
Output connectors
DVI：24+5 DVI_I
Others
Control
RS232/USB/LAN
Input voltage
100-240VAC 50/60Hz
Maximum Power
Consumption
≤100W
Environment
Temperature
0-45 ℃
Environment
Humidity
15-85%
Dimension
482.6(L) x 300(W) x 89(H)mm
Weight
Cross weight：Kg, Net weight：Kg
10 / 38
Chapter 4 Front panel
Button introduction
1. Inputs（In-A、In-B、In-C、In-D、In-E、In-F）: stand for 6 input cards
accordingly. When pressing a button to select a card,if the indicator is on
red,it means the operation of the current input card is valid. Take button
is on, this group buttons are used for input cards matrix switcher.
1
5/6
7/8/9
2
3
4
10/11/12
11 / 38
2. SDI、DVI、VGA、Video：Input card selection,when selecting an input
signal, if the indicator is on green. It means the signal is
available.Otherwise the light will flicker.
3. PIP：turn on or off the picture-in-picture function. If the indicator is on and
flicker, it means signals should be selected.After selected one signal
from “Input Card Sources”, it will be on green light. PIP signal can be
same as or different from the main pic signal.
4. Outputs（ Out1、 Out2、 Out3、 Out4、 Out5、 Out6）： output ports
selection.When select one card and the indicator is on red light, it means
the operation of the current output card is valid.
5. Knob ： turn it to adjust the value or choose parameter on the
menu,available for turning left and right.
6. OK：press it to confirm the operation.
7. ↑Brt+,↓Brt-：versatile buttons, “↑” and “↓” are used to select an item
under setting situation. While Brt+ and Brt- are used to adjust the
brightness under operation situation.
8. ：return to the previous menu.
9. Setup ：enter the setup menu.
10. Take：matrix switcher on-off
Take is on.Inputs（In-A、In-B、In-C、In-D、In-E、In-F）function is output
port signal selection. Press Take，Take is off。
When Take is off，Inputs（In-A、In-B、In-C、In-D、In-E、In-F）function
is input card selection. Press Take，Take is on.
11. Lock：press the button and the indicator is on red light, all the other
buttons are locked. Press the button again for 3 times, all the other buttons
are unlocked and the light is off.
12. Info：display the system information. We can press this button to check
different status and parameters of the device.
12 / 38
Chapter5. Basic operation introduction
When system starts, it will automatically detect and identify the number
and location of input cards and output cards. The LCD panel will display the
information accordingly. The introduction of basic operations is based on full
configuration (6 PCS of input cards and 2 PCS of output cards) and the
default menu will be as follows when system starts:
5-1 Select input signals for input cards
Press SDI、DVI、VGA、Video to switch signals. Press In-A、In-B、
In-C、In-D、In-E、In-F to select an input card for operation.
5-2 PIP setup of input cards
Press PIP to enter PIP ready，then press SDI、DVI、VGA、Video to
choose PIP signal. Press In-A、In-B、In-C、In-D、In-E、In-F to choose
input card for operation.
5-3. Switch output ports signals
Press Take to enter Matrix switch ready.Take is on；
Press Out1、Out2、Out3、Out4、Out5、Out6 to choose output port.
Press In-A、In-B、In-C、In-D、In-E、In-F to choose output port signal.
5-4 Setting output ports switching effects
press Fade to set switching effects. This is available for current
ports or all ports. Refer to 33
rd
page” setting output switching effect”
5-5 Setting output cards to preview mode
Press Setup to enter user settings. Press ↑,↓ button to choose
“ output card setup” and press OK to enter menu. Press ↑,↓ button to
choose” Advance setup” and enter. Press ↑,↓ button to choose”
In-D(Input Card D)
Source： DVI 2s
Status： No PIP/Text
Out(Output Port)
Out-K Out1: In-A Fade 3s
Out2: In-F Cut
Out3: In-D Fade 2s
Out-L Out4: In-B Cut
Out5: In-C Cut
Out6: In-A Fade 1s
13 / 38
Preview” and rotate knob to adjust. Press OK to enter “ data reset
confirm” menu;
Press Out1、Out2、Out3 to choose Out-K setup；
Press Out4、Out5、Out6 to choose Out-L setup；
Under “data reset”confirm menu， Press OK to change preview setup.
Notices: change preview setup will reset the output card data. Pls do not
change if unnecessary.
5-6 Brightness setup
The adjusting range of brightness is 0-32, “0” stands for the lowest
brightness, press “Brt+”to increase the brightness or “Brt-”to lower it.To
make sure of the complete grey level of the output images,the default is
set as “32”and we can turn the knob to adjust brightness for one or two
output cards.
Tips
--------------------------------------
Data will reset
Press <OK> to reset
Press <return> to cancel
--------------------------------------
Output Card Advanced Setup
Out-L
--------------------------------------
1.Preview Off
2.Auto Detect Off
3.CH Reset
4.Refresh Data
5.Reset Data
--------------------------------------
14 / 38
5-7 Automatic VGA calibration
When the current input signal is VGA and it is valid,press “VGA” to enter
the confirmation menu of VGA automatic calibration,press “VGA”one
more time to confirm calibration and then to quit the menu,The
menu is as follows:
5-8 Button lock
Press “Lock”,other buttons will be locked in case of wrong operation.On
the menu of “Button Lock”,press “Lock” three times to quit the lock
state.When buttons are locked,only LAN,RS232 and USB
communication are available in case of the conflict between remote
control and panel control.When commands are sent from
remote,buttons will be automatically locked.
The menu is as follows:
Tips
--------------------------------------
VGA auto adjust
Press <VGA> to start
Press <return> to cancel
--------------------------------------
Out-L Brightness
--------------------------------------
1.Brightness 32
--------------------------------------
15 / 38
5-9 Check system information
Press “Info” to enter the menu of system information,and then press
“↑,↓”to turn the page and “ ” to quit.The menu is as follows:
Chapter6 User settings
User settings are used for the overall system setup,these settings
consist of 3 parts:input card,output card and the system.On the default
menu,when system starts,press “Setup” to enter the menu of “User
settings” and“↑,↓” to select settings,press “OK” to confirm,and “ ” to
quit the menu.
Following is the detailed instruction of each setting:
6-1 Input cards setup
Press “Setup” to enter the menu of “User settings”, “↑,↓”to select
“Input Card Setup”, press “OK” to enter the sub menu. Press “In-B or
In-D” to select an input card to change its settings.
System Info
--------------------------------------
Model/Version： LVS600 V0.1.0
IP: 192.168.1.10
Mask： 255.255.255.0
Gate： 192.168.1.1
MAC： 76-64-77-1A-2B-3C
Out Format： 1920x1200_60Hz
Device ID: 1
--------------------------------------
Button Lock
--------------------------------------
Button Invalid
LAN Valid
RS232 Valid
USB Valid
--------------------------------------
16 / 38
1. Set the size and location of main image
On the menu of “Input Card Setup”, press “↑,↓” to select “Main
Setup”, and “OK” to enter the sub menu.
Press “↑,↓” to select the setting, turn the knob to adjust and then press
“OK” to confirm.
Input Card Main Setup
In-A
--------------------------------------
1.Hori Width 666 -> 888
2.Hori Start 88
3.Vert Height 666
4.Vert Start 66
--------------------------------------
Setup
--------------------------------------
1.Input Card Setup
2.Output Card Setup
3.System Setup
--------------------------------------
In-B Setup
--------------------------------------
1.Main Setup
2.PIP Setup
3.Image Setup
4.Text Setup
5.Advanced Setup
--------------------------------------
17 / 38
2.Set the size and location of PIP
On the menu of “Input Card Setup”, press “↑,↓”to select “PIP
Setup”, press “OK” to enter the sub menu.
Press “↑,↓” to select the setting, turn the knob to adjust and then press
“OK” to confirm.
3.Set brightness, contrast and color
On the menu of “Input Card Setup”, press “↑,↓”to select “ Image
Setup”, and “OK” to enter the sub menu.
Input Card PIP Setup
In-A
--------------------------------------
1.Hori Width 666 -> 888
2.Hori Start 88
3.Vert Height 666
4.Vert Start 66
--------------------------------------
In-B Setup
--------------------------------------
1.Main Setup
2.PIP Setup
3.Image Setup
4.Text Setup
5.Advanced Setup
--------------------------------------
18 / 38
Press “↑,↓” to select the setting, turn the knob to adjust and then press
“OK” to confirm.
The adjusting range of brightness, contrast and color is
0-100.Brightness adjusting is only valid for the selected input card, if the
adjusting is wrong, press “Reset” to return to the default.
Notice:to change the settings is not recommended,unless brightness
adjusting through the panel buttons can’t meet customers’
requirements.
4. Set text on/off,text source and text mode
On the menu of “Input Card Setup”, press “↑,↓”to select “Text Setup”,
press “OK” to enter the sub menu.
Input Card Image Setup
In-A
--------------------------------------
1.Brightness 50
2.Contrast 50
3.Color 50 –> 56
4.Reset
--------------------------------------
In-B Setup
--------------------------------------
1.Main Setup
2.PIP Setup
3.Image Setup
4.Text Setup
5.Advanced Setup
--------------------------------------
19 / 38
Press “↑,↓” to select the setting, turn the knob to adjust and then press
“OK” to confirm
5.Advanced setup
On the menu of “Input Card Setup”, press “↑,↓”to select “ Advanced
Setup”, press “OK” to enter the sub menu.
In-B Setup
--------------------------------------
1.Main Setup
2.PIP Setup
3.Image Setup
4.Text Setup
5.Advanced Setup
--------------------------------------
In-B Setup
--------------------------------------
1.Main Setup
2.PIP Setup
3.Image Setup
4.Text Setup
5.Advanced Setup
--------------------------------------
Input Card Text Setup
In-B
--------------------------------------
1.Text Off
2.Text Source DVI
3.Text Mode >Threshold
4.Text R 4
5.Text G 8 –> 12
6.Text B 4
--------------------------------------
20 / 38
Set fade time
On the menu of “Input Card Advanced Setup”, press “↑,↓”to
select “ Fade Time”, turn the knob to adjust, and press “OK” to confirm.
HDMI hot plug on/off
On the menu of “Input Card Advanced Setup”, press “↑,↓” to
select “HDMI hot plug”, turn the knob to adjust and press “OK” to
confirm.
Notice: when switching signal sources, LVP608 will send “hot plug
signal” to HDMI devices.Then the device will update HDMI signal flow
and work normally. In this situation,a small number of HDMI devices
can’t work normally in extended desktop,then you can turn it off.
Generally we don’t suggest you to turn it off.
Refresh data
On the menu of “Input Card Advanced Setup”, press “↑,↓” to
select “Refresh Data” and press “OK” to confirm.
Input Card Advanced Setup
In-D
--------------------------------------
1.Fade 0.5s
2.HDMI Hot Plug On
5.Refresh Data
6.Reset Data
--------------------------------------
Input Card Advanced Setup
In-D
--------------------------------------
1.Fade 0.5s
2.HDMI Hot Plug On
3.Refresh Data
4.Reset Data
--------------------------------------
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
/