Sauder 410794 User manual

sauder.com

Storage

Bed/Headboard

Model 410794

NOTE: THIS INSTRUCTION

BOOKLET CONTAINS IMPORTANT

SAFETY INFORMATION.

PLEASE READ AND KEEP FOR

FUTURE REFERENCE.

English pg 1-30

Français pg 31-34

Español pg 35-38

Lot # 530470 06/19/19

Purchased: __________________

sauder.com

CONTACT US FIRST

BEFORE MAKING ANY RETURNS TO THE STORE.

Share your journey!

sauder.com

CONTACT US FIRST

BEFORE MAKING ANY RETURNS TO THE STORE.

Visit sauder.com/service to order replacement parts, view video assembly tips, or chat with a live rep.

Prefer the phone? Give us a ring at

1-800-523-3987.

Customer Service is available Monday-Friday - 9 a.m. to 5:30 p.m. EST (except holidays)

You won't just fall in

love with it. You'll fall

asleep in it.

Table of Contents Assembly Tools Required

2-3

4

5-30

31-34

35-38

39

Part Identiﬁ cation

Hardware Identiﬁ cation

Assembly Steps

Français

Español

Warranty

Hammer

Not actual size

No. 2 Phillips Screwdriver

Tip Shown Actual Size

Skip the power trip.

This time.

410794 www.sauder.com/servicePage 2

Part Identiﬁ cation

å While not all parts are labeled, some of the parts will have a label or an inked letter on the edge

to help distinguish similar parts from each other. Use this part identiﬁ cation to help identify similar parts.

A RIGHT END (1)

A2 BOTTOM (2)

B LEFT END (1)

B2 BOTTOM SUPPORT (2)

B19 DRAWER BOTTOM (2)

C3 LOWER UPRIGHT (1)

D UPRIGHT (2)

D44 RIGHT DRAWER SIDE (2)

D45 LEFT DRAWER SIDE (2)

D453 DRAWER DIVIDER (2)

D476 DRAWER BACK (2)

E HEADBOARD (1)

F FOOTBOARD (1)

G2 UPPER FRONT PANEL (1)

H2 LOWER FRONT PANEL (1)

I2 BACK PANEL (1)

J TOP (1)

J2 SLAT (4)

L SHELF (1)

M SHELF BRACE (1)

M67

DRAWER BRACE (2)

(Hidden part using recycled

material. Color may vary.)

N LOWER BRACE (1)

R ADJUSTABLE SHELF (1)

S LEFT DRAWER FRONT (1)

T RIGHT DRAWER FRONT (1)

X BACK (1)

Part Identiﬁ cation

Now you know

our ABCs.

410794www.sauder.com/service

Page 3

A

B

C3

D

E

F

G2

H2

I2

J

A2

L

M

N

M67

R

T

X

D44

B2

A2

D

J2

B2

D476

B19

D45

D453

M67

S

D44

D476

B19

D45

D453

Hardware Identiﬁ cation

å Screws are shown actual size. You may receive extra hardware with your unit.

410794 www.sauder.com/servicePage 4

35GA

CABINET RIGHT - 2

35GB

CABINET LEFT - 2

35GC

DRAWER RIGHT - 2

35GD

DRAWER LEFT - 2

ANGLE

BRACKET - 4

5G

SUPPORT

PIN - 12

4R

12E

TACK

GLIDE - 14

CAM

COVER - 6

12P

METAL

PIN - 8

1R

RUBBER

SLEEVE - 4

2R

SILVER 1-1/8" FLAT HEAD SCREW - 23

10S

BLACK 9/16" LARGE HEAD SCREW - 32

1S

3S

GOLD 5/16" FLAT HEAD SCREW - 16

NAIL - 30

1N

BRACKET - 6

1G

BROWN 1-5/8" FLAT HEAD SCREW - 10

55S30S

BLACK 1-9/16" FLAT HEAD SCREW - 10

BLACK 1-7/8" FLAT HEAD SCREW - 4

2S

HIDDEN

CAM - 34

1F

CAM

DOWEL - 34

2F

METAL

BRACKET - 2

4G

DRAWER FRONT

BRACKET - 2

8G

Step 1

Look for this icon. It means a

video assembly tip is available at

www.sauder.com/service/tips

å

Assemble your unit on a carpeted ﬂ oor or on the empty carton

to avoid scratching your unit or the ﬂ oor.

å

Push thirty-four HIDDEN CAMS (1F) into the ENDS (A and B),

UPRIGHTS (C3 and D), PANELS (G2, H2, and I2), SHELF (L), and

BRACES (M, N, and M67). Then, insert a CAM DOWEL (2F) into

each HIDDEN CAM.

410794www.sauder.com/service

Page 5

Do not tighten the HIDDEN CAMS in this step.

Insert the metal end of the CAM

DOWEL into the HIDDEN CAM.

Arrow

A

B

C3

D

G2

H2

I2

L

M

N

D

M67

(34 used)

Arrow

1F

2F

Step 2

å

IMPORTANT: The Headboard can be attached to either

end of the Storage Bed. In the following steps, assemble

your unit according to what option you choose.

410794 www.sauder.com/servicePage 6

Headboard on the RIGHT

Headboard on the LEFT

å

Fasten a CABINET RIGHT (35GA) and CABINET

LEFT (35GB) to the HEADBOARD (E) and FOOTBOARD (F).

Use four GOLD 5/16" FLAT HEAD SCREWS (3S).

Step 3

410794www.sauder.com/service

Page 7

Headboard on the RIGHT

Headboard on the LEFT

GOLD 5/16" FLAT HEAD SCREW

(4 used in this step)

3S

Roller end

F

E

F

Finished surface

Rounded edge

Step 4

å

Fasten a CABINET RIGHT (35GA) and CABINET

LEFT (35GB) to the LOWER UPRIGHT (C3). Use four

GOLD 5/16" FLAT HEAD SCREWS (3S).

410794 www.sauder.com/servicePage 8

GOLD 5/16" FLAT HEAD SCREW

(4 used in this step)

3S

Roller end

Surface with

HIDDEN CAMS

Roller end

C3

These HIDDEN CAMS are

closer to this edge.

å

Fasten the UPRIGHTS (D) to the TOP (J). Tighten two

HIDDEN CAMS.

å

Fasten the SHELF (L) to the UPRIGHTS (D). Use four

BLACK 1-7/8" FLAT HEAD SCREWS (2S).

Step 5

410794www.sauder.com/service

Page 9

Start Tighten

Arrow

Minimum

190 degrees

Caution

Risk of damage or

injury. HIDDEN CAMS

must be completely

tightened. HIDDEN

CAMS that are not

completely tightened

may loosen, and parts

may separate. To

completely tighten:

Arrow

Maximum

210 degrees

D

L

D

Do not stand the unit upright without the

BACK fastened. The unit may collapse.

Caution

Surface with

HIDDEN CAMS

Surface with HIDDEN CAM

J

Angled edge

BLACK 1-7/8" FLAT HEAD SCREW

(4 used in this step)

2S

Step 6

å

Fasten four ANGLE BRACKETS (5G) to the SHELF BRACE (M).

Use four BLACK 9/16" LARGE HEAD SCREWS (1S).

å

NOTE: Be sure the edges of the ANGLE BRACKETS are even

with the edge of the SHELF BRACE.

å

Fasten the SHELF BRACE (M) to the SHELF (L). Use four

BLACK 9/16" LARGE HEAD SCREWS (1S).

410794 www.sauder.com/servicePage 10

Surface with HIDDEN CAMS

5G

M

L

BLACK 9/16" LARGE HEAD SCREW

(8 used in this step)

1S

Angled edge

These surfaces should be even.

å

Fasten the ENDS (A and B) to the TOP (J), SHELF (L), and

SHELF BRACE (M). Tighten twelve HIDDEN CAMS.

å

Fasten two METAL BRACKETS (4G) to the ENDS (A and B).

Use two BLACK 9/16" LARGE HEAD SCREWS (1S).

å

NOTE: Be sure the BRACKETS are even with the edges of

the ENDS (A and B).

Step 7

410794www.sauder.com/service

Page 11

Arrow

Minimum

190 degrees

Maximum

210 degrees

Surface

with

HIDDEN

CAMS

B

M

L

J

Finished edge

Surface

without

HIDDEN

CAMS

A

Finished edge

BLACK 9/16" LARGE HEAD SCREW

(2 used for the METAL BRACKETS)

1S

4G

Step 8

å

Carefully lay your unit onto its front edges.

å

Insert two METAL PINS (1R) into the LOWER BRACE (N).

å

Fasten the LOWER BRACE (N) to the ENDS (A and B).

Tighten two HIDDEN CAMS.

å

NOTE: Be sure the METAL PINS in the LOWER BRACE

insert into the holes in the ENDS.

410794 www.sauder.com/servicePage 12

Arrow

Minimum

190 degrees

Maximum

210 degrees

Surface with HIDDEN CAMS

N

B

A

1R

å

Lay the BACK (X) over your unit.

å

Make equal margins along all four edges of the BACK (X).

Push on opposite corners of your unit if needed to make

it "square".

å

Fasten the BACK (X) to your unit using the NAILS (1N).

å

NOTE: Be sure to tap NAILS into the holes that line up

over the UPRIGHTS (D).

å

NOTE: Perforations have been provided for access

through the BACK. Carefully cut out the holes needed.

å

Using your hammer, tap four TACK GLIDES (12E) into the

bottom edges of the ENDS (A and B).

Step 9

410794www.sauder.com/service

Page 13

Do not stand the unit upright without the

BACK fastened. The unit may collapse.

Caution

Unﬁ nished surface

These holes must line up

over the UPRIGHTS (D).

NAIL

(30 used in this step)

1N

12E

B

A

X

The perforations

must be here.

Step 10

å

Using your hammer, tap ten TACK GLIDES (12E) into the

edges of the LOWER UPRIGHT (C3), HEADBOARD (E),

FOOTBOARD (F), LOWER FRONT PANEL (H2), and

BACK PANEL (I2).

410794 www.sauder.com/servicePage 14

H2

I2

C3

E

F

Unﬁ nished edge

12E

å

Fasten the SLATS (J2) to the UPPER FRONT PANEL (G2)

and BACK PANEL (I2). Use twelve SILVER 1-1/8" FLAT

HEAD SCREWS (10S).

å

Fasten the BOTTOM SUPPORTS (B2) to the

HEADBOARD (E) and FOOTBOARD (F). Use eight

SILVER 1-1/8" FLAT HEAD SCREWS (10S).

å

Insert a METAL PIN (1R) into each HEADBOARD (E) and

FOOTBOARD (F).

Step 11

410794www.sauder.com/service

Page 15

Rounded edge

SILVER 1-1/8" FLAT HEAD SCREW

(20 used in this step)

10S

Edge without holes

B2

J2

B2

J2

I2

G2

J2

F

E

Edge without holes

1R

Step 12

å

Carefully stand your unit upright.

å

Fasten the HEADBOARD (E) to the LOWER BRACE (N).

Use three SILVER 1-1/8" FLAT HEAD SCREWS (10S).

å

Fasten the HEADBOARD (E) to the METAL BRACKETS on

the ENDS (A and B). Use two BLACK 9/16" LARGE

HEAD SCREWS (1S).

å

NOTE: Follow steps 13-16 for Headboard on the Right.

å

NOTE: Follow steps 17-20 for Headboard on the Left

410794 www.sauder.com/servicePage 16

Headboard on the RIGHT

Headboard on the LEFT

BLACK 9/16" LARGE HEAD SCREW

(2 used for the METAL BRACKETS)

1S

SILVER 1-1/8" FLAT HEAD SCREW

(3 used for the LOWER BRACE)

10S

SILVER 1-1/8" FLAT HEAD SCREW

(3 used for the LOWER BRACE)

10S

Finished

surface

Finished

surface

Roller end

Rounded edge

Roller end

Rounded edge

E

N

B

A

B

N

E

å

Fasten the BACK PANEL (I2) to the HEADBOARD (E).

Tighten three HIDDEN CAMS.

å

Fasten the LOWER UPRIGHT (C3) to the BACK PANEL (I2).

Tighten two HIDDEN CAMS.

Step 13

410794www.sauder.com/service

Page 17

Arrow

Minimum

190 degrees

Maximum

210 degrees

Roller end

Finished edge

Unﬁ nished surface

C3

E

I2

These HIDDEN CAMS are

closer to the long edge.

Headboard on the RIGHT

Step 14

å

Fasten the LOWER FRONT PANEL (H2) to the

HEADBOARD (E) and LOWER UPRIGHT (C3). Tighten

two HIDDEN CAMS.

å

NOTE: Be sure the METAL PIN in HEADBOARD inserts

into the hole in the LOWER FRONT PANEL.

å

Fasten the UPPER FRONT PANEL (G2) to the

HEADBOARD (E) and LOWER UPRIGHT (C3). Tighten

three HIDDEN CAMS.

410794 www.sauder.com/servicePage 18

Arrow

Minimum

190 degrees

Maximum

210 degrees

Finished edge

Surface without HIDDEN CAMS

C3

Unﬁ nished edge

G2

E

Surface without HIDDEN CAMS

H2

Headboard on the RIGHT

å

Fasten the FOOTBOARD (F) to the FRONT PANELS (G2

and H2) and BACK PANEL (I2). Tighten six HIDDEN CAMS.

å

NOTE: Be sure the METAL PIN in the FOOTBOARD inserts

into the hole in the LOWER FRONT PANEL.

Step 15

410794www.sauder.com/service

Page 19

Arrow

Minimum

190 degrees

Maximum

210 degrees

G2

H2

I2

F

Rounded edge

Headboard on the RIGHT

Surface without holes

Step 16

å

Fasten the BRACKETS (1G) to the BOTTOM SUPPORTS (B2),

LOWER UPRIGHT (C3), and PANELS (G2, H2, and I2). Use

twelve BLACK 9/16" LARGE HEAD SCREWS (1S).

C3

B2

BLACK 9/16" LARGE HEAD SCREW

(12 used in this step)

1S

G2

H2

I2

1G

Headboard on the RIGHT

410794 www.sauder.com/servicePage 20

Page is loading ...

Sauder 410794 User manual

This manual is also suitable for

Sauder 410794 User manual

in other languages

Related papers

Other documents