Sauder 411836 User manual

PLEASE CONTACT US

BEFORE RETURNING

YOUR UNIT TO THE STORE

1-800-523-3987

www.sauder.com

411836

4-Drawer Chest

Palladia Collection

English .................... Page 1-24

Français ...............Pages 25-28

Espanol .............Páginas 29-32

Made in the USA

Archbold, OH

NOTE: THIS INSTRUCTION BOOKLET CONTAINS

IMPORTANT SAFETY INFORMATION.

PLEASE READ AND KEEP FOR FUTURE REFERENCE.

Lot #: 353119 05 / 08 / 13

Date Purchased: ____________________

WARNING

CHOKING HAZARD - Small Parts

Not for children under 3 years.

Adult assembly required.

TABLE OF CONTENTS

Part Identiﬁ cation .......................3

Hardware Identiﬁ cation ......... 4-5

Assembly Steps ....................6-24

Français ..............................25-28

Espanol ...............................29-32

Safety .................................33-34

Warranty ...................................35

Page 2 www.sauder.com/services 411836

ASSEMBLY TOOLS REQUIRED

Hammer

No. 2 Phillips Screwdriver

Tip Shown Actual Size

ADULT ASSEMBLY REQUIRED

PART IDENTIFICATION: While not all parts are labeled, some of the parts will have a label or an inked

letter on the edge to help distinguish similar parts from each other. Use this PART IDENTIFICATION to help

identify similar parts.

A RIGHT END 1

B LEFT END 1

C TOP 1

D BOTTOM 1

E BACK 1

F DRAWER BRACE 4

G BASE 1

H

LARGE DRAWER

FRONT

3

I LARGE DRAWER BACK 3

J LARGE DRAWER SIDE 6

K DRAWER BOTTOM 4

L

SMALL DRAWER

FRONT

1

M RIGHT MOLDING 1

N LEFT MOLDING 1

O SMALL DRAWER BACK 1

P SMALL DRAWER SIDE 2

Q FRONT MOLDING 1

R2 PLINTH 2

S BOTTOM MOLDING 1

T

DRAWER FRONT

MOLDING

1

U BALLAST 1

V BRACE 1

A

B

C

D

E

G

H

I

J

K

L

M

N

O

P

Q

R2

S

T

U

F

V

Page 3

www.sauder.com/services411836

HARDWARE IDENTIFICATION

SAFETY BRACKET - 1

II

TIE PLATE - 2

EE

METAL

BRACKET - 5

JJ

HIDDEN CAM - 9

1F

TWIST-LOCK® FASTENER - 10

AA

MOLDING CONNECTOR - 2

NN

METAL PIN - 2

DD

CAM SCREW - 9

8F

GG

SAFETY STOP - 4

QQ

WARNING LABEL - 1

(Refer to the last step for proper location and application)

WARNING

!

Serious or fatal crushing injuries can

occur from furniture tip-over. To help

prevent tip-over:

• Place heaviest items in the lowest drawers.

• Unless speciﬁ cally designed to accommodate, do not

set TVs or other heavy objects on top of this product.

• Never allow children to climb or hang on drawers,

doors, or shelves.

• Never open more than one drawer at a time.

• If equipped with a drawer interlock system, do not

defeat or remove it.

Use of tip-over restraints may only reduce,

but not eliminate, the risk of tip-over.

This is a permanent label. Do not attempt to remove!

04/10 332296

INTERLOCK TRACK - 1

OO

DRAWER FRONT BRACKET - 1

LL

LARGE DRAWER FRONT BRACKET - 6

MM

KK

CLIP - 16

DRAWER BOTTOM

BRACKET - 4

HH

FF

DRAWER ACTUATOR - 4

KNOB - 8

PP

Page 4 www.sauder.com/services 411836

35GA

CABINET RIGHT - 4

35GB

CABINET LEFT - 4

35GC

DRAWER RIGHT - 4

35GD

DRAWER LEFT - 4

Screws are shown actual size. You may receive extra hardware with your unit.

HARDWARE IDENTIFICATION (CONTINUED)

BLACK 1-1/8” PAN HEAD SCREW - 4

TT

GOLD 1” MACHINE SCREW - 2

UU

SILVER 1/2” MACHINE SCREW - 6

WW

VV

BLACK 9/16” LARGE HEAD SCREW - 35

BLACK 1-1/4” FLAT HEAD SCREW - 7

SS

BROWN 1-1/2” FLAT HEAD SCREW - 4

RR

GOLD 5/16” FLAT HEAD SCREW - 32

XX

NAIL - 50

YY

Page 5

www.sauder.com/services411836

Look for this icon. It means a video

assembly tip is available at:

www.sauder.com/services/tips

1

S

t

e

p

Assemble your unit on a carpeted ﬂ oor or on the empty carton to avoid scratching your unit or the ﬂ oor.

To begin assembly, push ten SAUDER TWIST-LOCK

®

FASTENERS (AA) into the large holes in the ENDS (A and B) and BOTTOM (D).

NOTE:

Do not tighten the TWIST-LOCK

®

FASTENERS at this time.

L

A

B

AA

Page 6 www.sauder.com/services 411836

(10 used)

2

S

t

e

p

Push nine HIDDEN CAMS (1F) into the BOTTOM (D), DRAWER BRACES (F) and BRACE (V).

Do not tighten the HIDDEN CAMS in this step.

Arrow

(9 used)

Arrow

Hole

F

D

V

Page 7

www.sauder.com/services411836

1F

3

S

t

e

p

Turn nine CAM SCREWS (8F) into the ENDS (A and B), LARGE DRAWER FRONTS (H), SMALL DRAWER FRONT (L) and

BOTTOM MOLDING (S).

(9 used)

A

B

H

L

S

Page 8 www.sauder.com/services 411836

8F

4

S

t

e

p

Tap two MOLDING CONNECTORS (NN) into the notches in the MOLDINGS (M, N and Q).

Fasten the MOLDINGS (M, N, and Q) to the TOP (C). Use seven BLACK 1-1/4" FLAT HEAD SCREWS (SS).

Flat end

Use your hammer to tap the MOLDING CONNECTOR (NN) into the notches in the MOLDINGS.

BLACK 1-1/4” FLAT HEAD SCREW

(7 used in this step)

SS

M

N

Q

Rounded edge

C

NN

Unﬁ nished surface

Finished surface

Page 9

www.sauder.com/services411836

The next three steps involve an important safety feature designed to prevent more than one drawer from opening at the same time.

Insert four SAFETY STOPS (GG) into the holes shown in the RIGHT END (A).

5

S

t

e

p

This pin must insert into the location

holes in the RIGHT END (A).

GG

A

Page 10 www.sauder.com/services 411836

Diagram 1. Measure 3” from one end of the INTERLOCK TRACK (OO).

Position the INTERLOCK TRACK as shown.

SAFETY STOP / TRACK ATTACHMENT:

Diagram 2. Tilt the first edge of the INTERLOCK TRACK (OO) into the SAFETY STOP (GG).

Diagram 3. Rotate the INTERLOCK TRACK and apply force to snap the second edge into the SAFETY STOP.

Diagram 4. Repeat the SAFETY STOP/ TRACK ATTACHMENT for the next SAFETY STOPS while holding the previously

completed SAFETY STOP in its location hole. Visually check that all INTERLOCK TRACK edges have been snapped into the

SAFETY STOPS as shown in diagram 3.

Diagram 5. Remove the INTERLOCK TRACK assembly from Diagram 4 and flip it over before inserting the INTERLOCK TRACK (OO)

with SAFETY STOPS (GG) into the groove in the RIGHT END (A).

6

S

t

e

p

2. 3.

1.

3"

4.

5.

Be sure the

interlock track

snaps into each

safety stop.

OO

GG

The interlock system is a safety feature that prevents

more than one drawer from opening at the same time.

Do not use excessive force to open the drawers.

Page 11

www.sauder.com/services411836

A

F

l

i

p

o

v

e

r

a

n

d

i

n

s

e

r

t

i

n

t

o

g

r

o

v

e

.

Fasten the CABINET RIGHTS (35GA) and CABINET LEFTS (35GB) to the ENDS (A and B). Use sixteen GOLD 5/16" FLAT

HEAD SCREWS (XX) through holes #1 and #3.

7

S

t

e

p

A

B

1

2

3

2

1

3

2

1

3

2

1

3

2

1

2

3

1

2

3

1

2

3

GOLD 5/16" FLAT HEAD SCREW

(16 used in this step)

XX

Page 12 www.sauder.com/services 411836

Roller end

Insert two METAL PINS (DD) into the short edges of the BRACE (V).

Fasten the BRACE (V) to the ENDS (A and B). Tighten two HIDDEN CAMS.

NOTE: Be sure the METAL PINS insert into the holes in the ENDS.

8

S

t

e

p

A

B

Finished edge

DD

V

Page 13

www.sauder.com/services411836

Surface with

HIDDEN CAMS

Fasten the TOP MOLDINGS (M and N) to the ENDS (A and B). Tighten four TWIST-LOCK

®

FASTENERS.

Fasten the BOTTOM (D) to the ENDS (A and B). Tighten four TWIST-LOCK

®

FASTENERS.

9

S

t

e

p

How to use the SAUDER TWIST-LOCK

®

FASTENER

1. Insert the dowel end of the FASTENER into the

hole of the adjoining part.

NOTE: The dowel end of the FASTENER must remain

fully inserted in the hole of the adjoining part while

locking the FASTENER.

2. Tighten the FASTENER with a Phillips screwdriver

as tight as possible.

Dowel end

M

N

A

B

D

Page 14 www.sauder.com/services 411836

Surface with

TWIST-LOCK® FASTENERS

These holes

must be here.

Fasten the BOTTOM MOLDING (S) to the BOTTOM (D). Tighten three HIDDEN CAMS.

Fasten two METAL BRACKETS (JJ) to the BOTTOM (D). Use two BLACK 9/16" LARGE HEAD SCREWS (VV).

Fasten the PLINTHS (R2) to the ENDS (A and B). Tighten two TWIST-LOCK

®

FASTENERS.

Fasten the PLINTHS (R2) to the BOTTOM (D). Use two BLACK 9/16" LARGE HEAD SCREWS (VV).

10

S

t

e

p

A

B

BLACK 9/16” LARGE HEAD SCREW

(4 used for the METAL BRACKETS)

VV

D

Unﬁ nished

Coved edge

S

R2

Page 15

www.sauder.com/services411836

JJ

Fasten the BALLAST (U) to the BOTTOM (D). Use four BLACK 1-1/8" PAN HEAD SCREWS (TT).

Fasten three METAL BRACKETS (JJ) to the BALLAST (U). Use three BLACK 9/16" LARGE HEAD SCREWS (VV).

Fasten the BASE (G) to the BALLAST (U). Use three BLACK 9/16" LARGE HEAD SCREWS (VV).

11

S

t

e

p

BLACK 1-1/8” PAN HEAD SCREW

(4 used in this step)

TT

U

BLACK 9/16” LARGE HEAD SCREW

(6 used for the METAL BRACKETS)

VV

Page 16 www.sauder.com/services 411836

JJ

G

Carefully turn your unit over onto its front edges. Unfold the BACK (E) and lay it over your unit.

Make equal margins along all four edges of the BACK (E). Push on opposite corners of your unit if needed to make it “square”.

Fasten the BACK (E) to your unit using the NAILS (YY).

Fasten two TIE PLATES (EE) to the PLINTHS (R2) and BASE (G). Use four BLACK 9/16" LARGE HEAD SCREWS (VV).

12

S

t

e

p

Do not stand the unit upright without the

BACK fastened. The unit may collapse.

Caution

NAIL

(34 used in this step)

YY

BLACK 9/16” LARGE HEAD SCREW

(4 used for the TIE PLATES)

VV

EE

G

R2

E

Page 17

www.sauder.com/services411836

Printed information

must be facing up.

Fasten the DRAWER FRONT MOLDING (T) to the SMALL DRAWER FRONT (L). Use three BROWN 1-1/2" FLAT HEAD

SCREWS (RR).

13

S

t

e

p

Unﬁ nished edge

BROWN 1-1/2” FLAT HEAD SCREW

(3 used in this step)

RR

T

Groove

L

Page 18 www.sauder.com/services 411836

Pull the DRAWER FRONT BRACKETS (LL and MM) apart and slide them into the grooves in the DRAWER SIDES (J and P).

Fasten the DRAWER FRONTS (H and L) to the DRAWER FRONT BRACKETS. Use sixteen BLACK 9/16” LARGE HEAD

SCREWS (VV).

Slide the DRAWER BOTTOMS (K) into the DRAWER SIDES (P and J).

14

S

t

e

p

Push down

BLACK 9/16” LARGE HEAD SCREW

(16 used in this step)

VV

LL

Tap down with your screwdriver and hammer.

K

J

P

L

H

Groove

Page 19

www.sauder.com/services411836

Slide the SMALL DRAWER BACK (O) into the grooves in the SMALL DRAWER SIDES (P).

Flip the drawer over and fasten the DRAWER BRACE (F) to the SMALL DRAWER FRONT (L). Tighten the HIDDEN CAM.

Insert the DRAWER BOTTOM BRACKET (HH) into the groove in the SMALL DRAWER BACK (O) and wrap it over the DRAWER

BRACE (F). Fasten the BRACKET (HH) to the DRAWER BRACE (F). Use a BLACK 9/16” LARGE HEAD SCREW (VV).

Insert four CLIPS (KK) into the groove in the SMALL DRAWER BACK (O) and wrap them over the DRAWER BOTTOM (K). Tap

a NAIL (YY) through each CLIP.

NOTE: The CLIPS should set in about 1" from the SMALL DRAWER SIDES.

Repeat this step for the other drawers.

15

S

t

e

p

Slide the DRAWER

BACK down.

BLACK 9/16” LARGE HEAD SCREW

(4 used for the DRAWER BOTTOM BRACKETS)

VV

Groove

NAIL

(16 used for the CLIPS)

YY

Surface with

HIDDEN CAM

O

P

HH

KK

F

(16 used)

(4 used)

Page 20 www.sauder.com/services 411836

O

L

K

Page is loading ...

Sauder 411836 User manual

Sauder 411836 User manual

in other languages

Related papers

Other documents