Amulet Hotkey CoreStation WR3930 Quick start guide

Brand: Amulet Hotkey

Model: CoreStation WR3930

Type: Quick start guide

CoreStation® WR3930

DXP4 Installation in a DellEMC 3930 Performance Workstation

Quick Start Guide

www.amulethotkey.com

QS-WR39-3001 v1.0 January 2020

For Health and safety informaon, refer to the sheet LS-AHKL-0001.

References

Refer also to the Dell publicaon, Precision 3930 Rack, RTX card Installaon

Guide for the secons on ESD precauons, what to do before working on your

computer and what to do aer working on your computer.

Requirements

To complete this installaon you will need:

 One or two DXP4s (M2200 GPU);

 Amulet Hotkey Custom Power Loom;

 Amulet Hotkey Custom RPC cable;

 USB-C cable to Display Port or HDMI output (display dependent).

Preliminary Setup

Before you install the DXP4 cards in the CoreStaon, you must rst set the fan

speeds in the BIOS.

Cauon: !

The BIOS must be version 2.3.0 or above.

1 Connect a USB-C cable from the WR3930 to a suitable display.

2 Power up the CoreStaon WR3930.

3 During the boot cycle, press F2 to enter the system setup.

4 Select Thermal Conguraon from the side menu.

5 Select CPU Zone and move the slider unl the value is 40.

6 Select PCIe Zone and move the slider unl the value is 40.

7 Click Apply and OK, then click Exit.

8 Power down the CoreStaon® WR3930.

Remove the cover

1 Use a Philips screw driver to rotate the lock to the release posion (1).

2 Li the latch (2) and move the cover away from the system (3).

Install the Amulet Hotkey Power cable

1 If installed, remove the Dell graphics card power cable from the clips on the

graphics card fan cage and the motherboard.

2 Push the single connector end of the Amulet Hotkey power cable into the

PCIe 8-pin socket on the motherboard.

Remove the riser1 module

1 Hold the blue contact points and li the riser1 module from the slot.

2 Pull the release tab to open the riser1 slot (1) and remove a riser blank (2)

from the slot.

www.amulethotkey.com

CoreStaon® WR3930 Quick Start Guide

Health and Safety (Refer also to the DXP4 manual HB-DXP4-0002)

• This device complies with part 15 of the FCC Rules (Class A)

• Operang temperature range: 15° to 35° C (59° to 95° F)

• Operang humidity range: 10% to 80% (non-condensing)

For product documentaon, downloads and technical assistance, visit:

For further informaon on all our products, visit www.amulethotkey.com.

Informaon in this document is subject to change. No part of this document may be reproduced through any means including (but not limited to) electronic or

mechanical, without express wrien permission from Amulet Hotkey Ltd. Amulet Hotkey Ltd may have patents, patent applicaons, trademarks or copyrights or other

intellectual property rights covering subject maer in this document. PC-over-IP, PCoIP and the PCoIP logo are registered trademarks of Teradici Corp. Amulet Hotkey

and ‘soluons you can bank on’ are registered trademarks of Amulet Hotkey Ltd. Other product names and company names listed within this document may be trade-

marks of their respecve owners. Amulet Hotkey products are designed and built in the UK.

Install the DXP4 card into the riser1 module

1 Install one or two DXP4s into the riser1 slots.

2 Close the riser1 module release latch.

3 Connect a free connector on the Amulet Hotkey power cable to the power

connector on a DXP4.

4 If a second DXP4 is present, repeat step 3.

5 Install one end of the Amulet Hotkey RPC cable into the

motherboard connector PWR CON1.

6 Connect a free connector on the Amulet Hotkey RPC cable to the RPC

connector on a DXP4.

7 If a second DXP4 is present, repeat step 6.

Install the riser1 module

1 Align the riser1 module with the alignment pins on the chassis and install

the riser1 module into the slot.

2 Tidy the RPC and power cables through the cable management clips.

Install the cover

1 Align the top cover tabs with the slots on the system chassis and slide it into

the slot. (Make sure all internal cables are routed correctly and connected).

2 Fold the release latch down and turn the lock with a Philips screw driver.

DHCP assignment.

Change the default IP address

If your network uses DHCP, the DXP4 obtains its IP address from the DHCP server.

If no DHCP server is available, the DXP4 mes out aer three minutes and adopts

its default IP address of 192.168.1.100.

Cauon: !

Change the default IP address as soon as possible.

All DXP4 cards will revert to the same default IP address, this can cause conicts

as the network grows. Use the Administrave Web Interface (AWI) to assign a

dierent stac IP address than the default.

1 Enter the IP address of the DXP4 into your browser to access the AWI.

2 Enter the default password ahkdante and click Log In.

3 From the Conguraon menu select the Network opon.

4 Make sure the Enable DHCP opon is unchecked.

5 Enter the new fall-back default IP address into the IP Address elds.

6 Make sure the Enable DHCP opon is checked.

Choose a connecon type (oponal)

1 To change the connecon type, select Opons > Conguraons > Sessions.

2 Click Unlock and enter the default password ahkdante.

To connect directly to a PCoIP host (Direct to Host + SLP

discovery)

1 Click the Connect buon.

The message ‘Discovering hosts’, followed by a list of available hosts

appears.

2 Select the chosen PCoIP host from the list and click OK.

The Connect buon is greyed out unl the zero client has a network

connecon and an IP address.

To connect to a virtual desktop (View Connecon Server)

1 Set the connecon type to View Connecon Server or View Connecon

Server + Auto Logon.

2 Enter the addWress of the View Connecon Server.

Amulet Hotkey CoreStation WR3930 Quick start guide

Amulet Hotkey CoreStation WR3930 Quick start guide

Amulet Hotkey CoreStation WR3930 Quick start guide

Related papers

Other documents