Amulet Hotkey DXM Quick start guide

Type
Quick start guide
www.amulethotkey.com
QS-MHC4-0004 v1.2 January 2020
Quick Start Guide
dual-slot mezzanine form factor
Remote Workstation Graphics Card for Dell 14G M-series blade servers
DXM
The DXM product is a range of KVM extender graphics host cards in a mezzanine
slot form factor (‘mezz cards’) for Dell M-series blade servers.
Dual and single-slot form factor versions of the DXM are available:
dual-slot: have an extended heat sink and occupy both mezzanine slots in an
M640 blade, the blade can only accommodate one of these cards.
single-slot: only occupy a single mezzanine slot. You can install them in pairs
or in tandem with a different card. Ideal for space constrained installations.
This guide tells you how to install and configure a dual-slot DXM mezz card on a
Dell M640 blade. See Figure 1 for an overview. There is a separate Quick Start
Guide for installing single-slot mezzanine cards.
All kits include a custom mounting bracket with auxiliary power cables.
Prepare the blade
Important! Alwaysuseanti-statichandlingprocedurestohandleaDXMcard
ortoworkontheinsideofablade.Keepliquidsawayfromthearea.
1. If the blade is not in a chassis, go to Step 4. If it’s used for 1 to 1, go to step 4.
2. If it is used for VDI, then shut down or migrate all VMs hosted by the blade.
3. In the VMware vSphere client, locate the ESXi server in the Inventory and
put it in to Maintenance Mode.
4. Shut down the host M640 blade and remove it from the chassis.
5. Open the blade and remove any installed mezzanine cards.
Remove the Dell mounting bracket
1. Remove the screw on the Dell mezzanine card mounting bracket and retain.
2. Remove the two screws from the Network Daughter Card (NDC) and retain.
3. Remove together the mounting bracket and NDC from the enclosure.
4. Discard this mounting bracket and install again the NDC with the two screws.
Install the mezzanine support bracket (part A)
Important!Thebracketonlyfitsonewayintheblade.
1. Move the support bracket (part A) into the blade so that the locating pins on
the bracket align with the two blade pin recesses. See Figure 2
.
Figure 1:Installationoverview
Install the mezzanine support bracket extension (part B)
1. Push the ends of the two arms of the mezzanine support bracket extension
(part B) into the holes on part A so that it clicks into place. See Figure 4.
Figure 2: Alignpinswiththebladepinrecesses
2. Move the bracket (part A) downwards. As the pins engage with the recesses,
make sure that the sprung leg engages under the NDC. See Figure 3.
DXM dual-slot
mezzanine host card
2
Figure 3: Movethesupportbracket(partA)intoposition
3. Install the retaining screw into the bracket.
Figure 4: Installthemezzaninesupportbracketextension(partB)
Connect the power cable
Important!TheDXMcardcaninstallinoneoftwopositionsandrequires
eitherashortpowercableformezzanineslotC,orlongformezzanineslotB.
1. Select the correct power cable, long for mezz slot B, short for mezz slot C.
2. Push the connector on the power cable through the square hole in the
bracket (part A) and into the socket on the motherboard. See Figure 5.
Important!Makesurethealignmentfeaturealignswiththesocket.
Figure 5: Connectthecorrectcabletothemotherboard
3. Record the MAC address from the label on the DXM.
4. Hold the DXM by the PCB or connector and push the free flat connector of
the power cable into the socket on the DXM.
1Dual-slotDXMmezzcard.2CustommountingbracketpartAandpartB.
3B/CMezzanineslotBandC.Note:Cardappearancemayvary.
1
B
A
M640 blade
3B
3C
www.amulethotkey.com
DXM Quick Start Guide (Dual slot form factor)
AMULET
HOTKEY
®
©2020 Amulet Hotkey Ltd. All rights reserved. Information in this document is subject to change. No part of this document may be reproduced through any means including (but not limited
to) electronic or mechanical, without express written permission from Amulet Hotkey Ltd. Amulet Hotkey Ltd may have patents, patent applications, trademarks or copyrights or other
intellectual property rights covering subject matter in this document. PC-over-IP, PCoIP and the PCoIP logo are registered trademarks of Teradici Corp. Amulet Hotkey and ‘solutions you can
bank on’ are registered trademarks of Amulet Hotkey Ltd. Other product names and company names listed within this document may be trademarks of their respective owners. Amulet
Hotkey products are designed and built in the UK.
Health and Safety (Refer to legislation sheet LS-AHKL-0001)
This device complies with part 15 of the FCC Rules (Class A)
Operating temperature range: 10° to 35° C (50° to 95° F)
Operating humidity range: 10% to 80% (non-condensing)
For product documentation, driver downloads and technical support, visit:
For further information on all our products, visit www.amulethotkey.com.
Install the DXM into the mezzanine support bracket
1. Align the DXM for mezz slot B or C on the mezzanine support bracket.
Note:TheheatsinkoftheDXM coversbothmezzconnectors,andprevents
theinstallationofanothermezzaninecard.
2. Turn the insertion tool up so you can see the letters DXM and locate the
insertion tool on top of the hexagonal spacers on the DXM. See Figure 6 (A).
3. Push down on the insertion tool with the heel of your hand to install the
DXM. See Figure 6 (B).
Figure 6:(A)Locatetheinsertiontool.(B)PushonthetooltoinstalltheDXM
4. Make sure the card sits level on the mezzanine support bracket.
5. Make sure the cable is routed through the cable management feature.
Install the mezzanine board support clip
1. Install the mezzanine board support clip on the edge of the blade chassis.
See Figure 7.
Note:InstallthecliponthenearsidetotheslotwheretheDXMisinstalled.
If you need to remove the DXM
Be careful to avoid contact between the chip located at the edge of the DXM
and the wall of the blade chassis if removing or replacing the card as this can
cause damage to the chip. See Figure 8.
You must take care if removing the DXM card from the blade chassis.
1. Hold the card by the sides. Disconnect the flat power cable.
2. Keep the card level and lift out slowly and carefully.
Figure 8:Locationofchiprelativetothebladechassis
Figure 7:Installthemezzanineboardsupportclip
Power up the blade
1. Close the blade.
2. Push the blade into the chassis and power up.
Set up the DXM for remote operation
1. See the RemoteDesktopConfigurationManual on our support website for
how to setup a blade for 1 to 1 remote operation.
2. See the KBA113-SetupVDI on our support website for how to setup Virtual
Desktop Infrastructure for applicable MXM GPU cards.
A B
  • Page 1 1
  • Page 2 2

Amulet Hotkey DXM Quick start guide

Type
Quick start guide

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI