H3C S5500-28F-EI Installation guide

H3C S5500-EI Series Ethernet Switches

Installation Manual

Hangzhou H3C Technologies Co., Ltd.

http://www.h3c.com

Manual Version: 20071215-C-1.01

No part of this manual may be reproduced or transmitted in any form or by any means

without prior written consent of Hangzhou H3C Technologies Co., Ltd.

Trademarks

H3C, , Aolynk, , H

3

Care,

, TOP G, , IRF, NetPilot,

Neocean, NeoVTL, SecPro, SecPoint, SecEngine, SecPath, Comware, Secware,

Storware, NQA, VVG, V

2

G, V

n

G, PSPT, XGbus, N-Bus, TiGem, InnoVision and

HUASAN are trademarks of Hangzhou H3C Technologies Co., Ltd.

All other trademarks that may be mentioned in this manual are the property of their

respective owners.

Notice

The information in this document is subject to change without notice. Every effort has

been made in the preparation of this document to ensure accuracy of the contents, but

all statements, information, and recommendations in this document do not constitute

the warranty of any kind, express or implied.

To obtain the latest information, please access:

http://www. h3c.com

Technical Support

customer_service@h3c.com

http://www. h3c.com

About This Manual

Related Documentation

In addition to this manual, each H3C S5500-EI Series Ethernet Switches

documentation set includes the following:

Manual Description

H3C S5500-EI Series Ethernet Switches

Operation Manual

It is used for assisting the users in data

configurations and typical applications.

H3C S5500-EI Series Ethernet Switches

Command Manual

It is used for assisting the users in using

various commands.

Organization

H3C S5500-EI Series Ethernet Switches Installation Manual is organized as follows:

Chapter Contents

1 Product Overview

Introduces the characteristics and technical

specifications of S5500-EI Series Ethernet Switches.

2 Installation Preparations

Introduces the installation preparation and precaution

of S5500-EI Series Ethernet Switches.

3 Installation

Introduces the procedures to install an S5500-EI

Series Ethernet Switch, including the setup of the

mainframe, cards and cables.

4 Initial Power-On

Introduces the booting process of an S5500-EI Series

Ethernet Switch, including the power-on booting of the

switch and the system initialization.

5 Boot ROM and Host

Software Loading

Introduces how to load Boot OM and host software for

an S5500-EI Series Ethernet Switch.

6 Maintenance and

Troubleshooting

Introduces the problems that might occur during the

installation and the booting of an S5500-EI Series

Ethernet Switch and the related solution.

Appendix A Lightning

Protection of the Switch

Introduces lightning protection of S5500-EI Series

Ethernet Switches.

Conventions

The manual uses the following conventions:

I. GUI conventions

Convention Description

< >

Button names are inside angle brackets. For example, click

<OK>.

[ ]

Window names, menu items, data table and field names

are inside square brackets. For example, pop up the [New

User] window.

/

Multi-level menus are separated by forward slashes. For

example, [File/Create/Folder].

II. Symbols

Convention Description

Warning

Means reader be extremely careful. Improper operation

may cause bodily injury.

Caution

Means reader be careful. Improper operation may cause

data loss or damage to equipment.

 Note Means a complementary description.

Environmental Protection

This product has been designed to comply with the requirements on environmental

protection. For the proper storage, use and disposal of this product, national laws and

regulations must be observed.

Installation Manual

H3C S5500-EI Series Ethernet Switches Table of Contents

i

Table of Contents

Chapter 1 Product Overview ........................................................................................................1-1

1.1 Introduction........................................................................................................................1-1

1.2 S5500-28C-EI....................................................................................................................1-2

1.2.1 Appearance.............................................................................................................1-2

1.2.2 Front Panel..............................................................................................................1-3

1.2.3 Rear Panel ..............................................................................................................1-3

1.2.4 Power Supply System.............................................................................................1-3

1.2.5 Cooling System.......................................................................................................1-4

1.2.6 LEDs........................................................................................................................1-4

1.3 S5500-28C-EI-DC..............................................................................................................1-7

1.3.1 Appearance.............................................................................................................1-7

1.3.2 Front Panel..............................................................................................................1-8

1.3.3 Rear Panel ..............................................................................................................1-8

1.3.4 Power System.........................................................................................................1-8

1.3.5 Cooling System.......................................................................................................1-9

1.3.6 LEDs........................................................................................................................1-9

1.4 S5500-52C-EI..................................................................................................................1-12

1.4.1 Appearance...........................................................................................................1-12

1.4.2 Front Panel............................................................................................................1-13

1.4.3 Rear Panel ............................................................................................................1-13

1.4.4 Power Supply System...........................................................................................1-13

1.4.5 Cooling System.....................................................................................................1-14

1.4.6 LEDs......................................................................................................................1-14

1.5 S5500-28C-PWR-EI ........................................................................................................1-14

1.5.1 Appearance...........................................................................................................1-14

1.5.2 Front Panel............................................................................................................1-14

1.5.3 Rear Panel ............................................................................................................1-15

1.5.4 Power Supply System...........................................................................................1-15

1.5.5 Cooling System.....................................................................................................1-15

1.5.6 LEDs......................................................................................................................1-15

1.6 S5500-52C-PWR-EI ........................................................................................................1-19

1.6.1 Appearance...........................................................................................................1-19

1.6.2 Front Panel............................................................................................................1-20

1.6.3 Rear Panel ............................................................................................................1-20

1.6.4 Power Supply System...........................................................................................1-21

1.6.5 Cooling System.....................................................................................................1-21

1.6.6 LEDs......................................................................................................................1-21

1.7 S5500-28F-EI...................................................................................................................1-21

Installation Manual

H3C S5500-EI Series Ethernet Switches Table of Contents

ii

1.7.1 Appearance...........................................................................................................1-21

1.7.2 Front Panel............................................................................................................1-22

1.7.3 Rear Panel ............................................................................................................1-22

1.7.4 Power System.......................................................................................................1-22

1.7.5 Cooling System.....................................................................................................1-23

1.7.6 LEDs......................................................................................................................1-23

1.8 System Specifications of the S5500-EI Series................................................................1-26

1.9 Pluggable Modules ..........................................................................................................1-28

1.10 Optional Interface Modules............................................................................................1-29

1.10.1 Description of LEDs on Extended Modules ........................................................1-30

1.11 CX4 Cable......................................................................................................................1-30

Chapter 2 Installation Preparations.............................................................................................2-1

2.1 Safety Precautions.............................................................................................................2-1

2.2 Installation Site...................................................................................................................2-1

2.2.1 Temperature/Humidity.............................................................................................2-1

2.2.2 Cleanness ...............................................................................................................2-2

2.2.3 Electromagnetic Susceptibility ................................................................................2-2

2.2.4 Laser Safety............................................................................................................2-3

2.3 Installation Tools................................................................................................................2-3

Chapter 3 Installation....................................................................................................................3-1

3.1 Installing the Switch into a 19-Inch Cabinet.......................................................................3-1

3.1.1 Introduction to Mounting Ears.................................................................................3-2

3.1.2 Introduction to Guide Rails......................................................................................3-3

3.1.3 Using Front Mounting Ears to Install the Switch.....................................................3-4

3.1.4 Using Front Mounting Ears and a Tray...................................................................3-5

3.1.5 Using Front and Rear Mounting Ears .....................................................................3-5

3.1.6 Using Front Mounting Ears and Guide Rails...........................................................3-8

3.2 Mounting the Switch on a Workbench.............................................................................3-10

3.3 Connecting the Power Cables and the Grounding Cable................................................ 3-11

3.3.1 Connecting the AC Power Cable ..........................................................................3-11

3.3.2 Connecting the DC Power Cable..........................................................................3-12

3.3.3 Connecting the Grounding Cable..........................................................................3-17

3.4 Connecting the Console Cable........................................................................................3-19

3.4.1 Console Cable.......................................................................................................3-19

3.4.2 Connection Procedure ..........................................................................................3-20

3.5 Installing and Removing Optional Interface Modules......................................................3-20

3.5.1 10 GE XFP Interface Module................................................................................3-21

3.5.2 Short-haul Dual-port 10 GE CX4 Interface Module...............................................3-23

3.6 Installing and Removing the Dedicated CX4 Cable.........................................................3-24

3.6.1 Installing the Dedicated CX4 Cable ......................................................................3-24

3.6.2 Removing the Dedicated CX4 Cable....................................................................3-24

3.7 Verifying the Installation...................................................................................................3-24

Installation Manual

H3C S5500-EI Series Ethernet Switches Table of Contents

iii

Chapter 4 Initial Power-On ...........................................................................................................4-1

4.1 Setting Up the Configuration Environment........................................................................4-1

4.2 Connecting the Console Cable..........................................................................................4-1

4.3 Setting Terminal Parameters.............................................................................................4-1

4.4 Booting the Switch.............................................................................................................4-5

4.4.1 Checking before Power-On.....................................................................................4-5

4.4.2 Powering On the Switch..........................................................................................4-5

4.4.3 Changing the Boot Mode ........................................................................................4-8

Chapter 5 Boot ROM and Host Software Loading ..................................................................... 5-1

5.1 Introduction to Loading Modes ..........................................................................................5-1

5.2 Local Software Loading.....................................................................................................5-1

5.2.1 Boot Menu...............................................................................................................5-2

5.2.2 Loading Software Using XModem Through the Console Port................................ 5-3

5.2.3 Loading Software Using TFTP through an Ethernet Port.......................................5-9

5.2.4 Loading Software Using FTP Through Ethernet Port........................................... 5-11

5.3 Remote Software Loading...............................................................................................5-12

5.3.1 Remote Loading Using FTP..................................................................................5-12

5.3.2 Remote Loading Using TFTP................................................................................5-14

Chapter 6 Maintenance and Troubleshooting............................................................................6-1

6.1 Software Loading Failure...................................................................................................6-1

6.2 Password Loss...................................................................................................................6-1

6.2.1 User Password Loss...............................................................................................6-1

6.2.2 BootROM Password Loss.......................................................................................6-2

6.3 Power Supply Failure.........................................................................................................6-2

6.4 Configuration System Failure ............................................................................................6-2

Installation Manual

H3C S5500-EI Series Ethernet Switches Chapter 1 Product Overview

1-1

Chapter 1 Product Overview

1.1 Introduction

H3C S5500-EI Series Ethernet Switches (hereinafter referred to as the S5500-EI series)

are Gigabit Ethernet switching products developed by Hangzhou H3C Technologies

Co., Ltd. (hereinafter referred to as H3C). The S5500-EI series support diversified

service features, IPv6 forwarding, and routing function, and provide 10GE extended

module slots. Through the H3C proprietary cluster management, you can streamline

network management. The S5500-EI series are designed to operate at the

convergence or access layer of enterprise networks and metropolitan area networks

(MANs). The S5500-EI series support the IPv4/IPv6 dual stack and can also be used

for connecting server groups in data centers.

Table 1-1 lists the models of the S5500-EI series.

Table 1-1 Models of the S5500-EI series

Model

Number of

auto-sensing

10/100/1000Base-T

Ethernet ports

Number of

1000Base-X SFP

ports

Number

of

console

ports

S5500-28C-EI 24 4

S5500-28C-EI-DC 24 4

S5500-52C-EI 48 4

S5500-28C-PWR-EI 24 4

S5500-52C-PWR-EI 48 4

S5500-28F-EI 8 24

1

Together with an auto-sensing 10/100/1000BASE-T Ethernet port, each 1000Base-X

SFP port forms a Combo port. For each Combo port, either the SFP port or the

auto-sensing 10/100/1000BASE-T Ethernet port can be used at a time. For the

mapping between the two ports forming a Combo port, refer to

Table 1-2.

Table 1-2 Mapping between two ports forming a Combo port

Model

1000Base-X SFP

port number

Auto-sensing 10/100/1000Base-T

Ethernet port number

25 22

26 24

S5500-28C-EI

S5500-28C-EI-DC

S5500-28C-PWR-EI

27 21

Installation Manual

H3C S5500-EI Series Ethernet Switches Chapter 1 Product Overview

1-2

Model

1000Base-X SFP

port number

Auto-sensing 10/100/1000Base-T

Ethernet port number

28 23

49 46

50 48

51 45

S5500-52C-EI

S5500-52C-PWR-EI

52 47

25 17

26 18

27 19

28 20

29 21

30 22

31 23

S5500-28F-EI

32 24

For the convenience of monitoring the running of the S5500-EI series, LEDs are also

equipped on their front panel.

1.2 S5500-28C-EI

1.2.1 Appearance

The S5500-28C-EI provides twenty-four auto-sensing 10/100/1000BASE-T Ethernet

ports, four 1000Base-X SFP ports, and one console port on the front panel, and one AC

power socket, one redundant power system (RPS) port, and two extended module slots

on the rear panel.

Figure 1-2 shows the appearance of the S5500-28C-EI.

Figure 1-1 Appearance of the S5500-28C-EI

Installation Manual

H3C S5500-EI Series Ethernet Switches Chapter 1 Product Overview

1-3

1.2.2 Front Panel

(1)

(2) (3) (4) (5) (6) (7) (8)

(9)

(10)

(1)

(2) (3) (4) (5) (6) (7) (8)

(9)

(10)

(1) Auto-sensing 10/100/1000Base-T Ethernet port status LEDs

(2) SFP port status LEDs

(3) Console port (4) 7-segment digital LED

(5) Power LED (6) RPS LED

(7) LED for extended module slot 1 (8) LED for extended module slot 2

(9) Mode LED (10) Mode button

Figure 1-2 Front panel of the S5500-28C-EI

1.2.3 Rear Panel

(1) (2)

(3)

(4)

(5)

(1) (2)

(3)

(4)

(5)

(1) AC power socket (2) RPS port

(3) Grounding screw (4) Extended module slot 1

(5) Extended module slot 2

Figure 1-3 Rear panel of the S5500-28C-EI

1.2.4 Power Supply System

The S5500-28C-EI can adopt AC input, or 12 V RPS input, or both to provide backup.

Only the recommended RPS can be used.

z AC power input

Rated voltage range: 100 VAC to 240 VAC, 50 Hz or 60 Hz

Input voltage range: 90 VAC to 264 VAC, 47 Hz to 63 Hz

z RPS input

Rated voltage range: 10.8 VDC to 13.2 VDC

Installation Manual

H3C S5500-EI Series Ethernet Switches Chapter 1 Product Overview

1-4

1.2.5 Cooling System

The S5500-28C-EI is equipped with four fans for heat dissipation.

1.2.6 LEDs

For descriptions about LEDs, see Table 1-3. You can switch the Mode LED display

mode between speed and duplex by pressing the Mode button on the panel.

Table 1-3 LEDs on the front panel of the S5500-28C-EI

LED Mark Status Description

Speed Solid green Rate of the port

Mode LED Mode

Duplex Solid yellow Duplex mode of the port

Solid green

The switch is started

normally.

Flashing green (1 Hz)

The system is running a

power-on self-test

(POST).

Solid red

The system fails the

POST or a power failure

occurs.

Flashing yellow (1 Hz)

Some ports fail a POST

or a port failure occurs.

Power LED PWR

OFF

The power is

disconnected.

Solid green

The AC power supply is

normal and the RPS is

connected and works

normally.

Solid yellow

The RPS input is

normal, but an AC input

failure occurs or no AC

power is connected.

Redundant power

system LED

RPS

OFF No RPS is connected.

Solid green

The module is in

position and works

normally.

Flashing yellow

The switch does not

support the module or a

module failure occurs.

Module LED MOD

OFF No module is installed.

Installation Manual

H3C S5500-EI Series Ethernet Switches Chapter 1 Product Overview

1-5

LED Mark Status Description

POST

running

The power

LED flashes

green

The LED displays the

POST test ID.

POST

failed

The power

LED flashes

red

The LED flashes the

POST test ID of the

failed test.

Software

loading

The power

LED flashes

green.

A bar rotates clockwise

around the LED.

Fan

failure

The power

LED is solid

red.

The LED displays F.

Over-tem

perature

alarm

The power

LED is solid

red.

The LED displays t.

7-segment digital

LED

Unit

Cluster

state

The power

LED is solid

green.

For a command switch,

the LED displays C.

For a member switch,

the LED displays S.

For a candidate switch,

the LED displays c.

The LED displays 1 if

there is only one unit.

Installation Manual

H3C S5500-EI Series Ethernet Switches Chapter 1 Product Overview

1-6

LED Mark Status Description

Green

A 1000 Mbps link is

present. When data is

being received or sent,

the LED flashes at a

high frequency.

Yellow

A 10/100 Mbps link is

present. When data is

being received or sent,

the LED flashes at a

high frequency.

Flashing

yellow (3 Hz)

The port fails the POST.

Speed

OFF No link is present.

Green

The port works in the full

duplex mode. The LED

flashes at a high

frequency when data is

being received or sent.

Yellow

The port works in the

half duplex mode. The

LED flashes at a high

frequency when data is

being received or sent

Flashing

yellow (3 Hz)

The port fails the POST.

10/100/1000Base

-T port status LED

—

Duplex

OFF No link is present.

Green

A 1000 Mbps link is

present. When data is

being received or sent,

the LED flashes at a

high frequency.

Flashing

yellow (3 Hz)

The port fails the POST.

SFP port status

LED (1000 Mbps)

—

The

Mode

button

has no

effect on

the LED.

OFF No link is present.

Installation Manual

H3C S5500-EI Series Ethernet Switches Chapter 1 Product Overview

1-7

LED Mark Status Description

Yellow

A 100 Mbps link is

present. When data is

being received or sent,

the LED flashes at a

high frequency.

Flashing

yellow (3 Hz)

The port failed the

POST.

Speed

OFF No link is present.

Green

The port operates in the

full duplex mode. When

data is being received or

sent, the LED flashes at

a high frequency.

Flashing

yellow (3 Hz)

The port fails the POST.

SFP port status

LED (100 Mbps)

—

Duplex

OFF No link is present.

1.3 S5500-28C-EI-DC

1.3.1 Appearance

The S5500-28C-EI-DC provides twenty-four auto-sensing 10/100/1000BASE-T

Ethernet ports, four 1000Base-X SFP ports, and one console port on the front panel,

and one –48 VDC power socket, one RPS port, and two extended module slots on the

rear panel.

Figure 1-4 shows the appearance of the S5500-28C-EI-DC.

Figure 1-4 Appearance of the S5500-28C-EI-DC

Installation Manual

H3C S5500-EI Series Ethernet Switches Chapter 1 Product Overview

1-8

1.3.2 Front Panel

(1)

(2) (3) (4) (5) (6) (7) (8)

(9)

(10)

(1)

(2) (3) (4) (5) (6) (7) (8)

(9)

(10)

(1) Auto-sensing 10/100/1000Base-T Ethernet port status LEDs

(2) SFP port status LEDs

(3) Console port (4) 7-segment digital LED

(5) Power LED (6) RPS LED

(7) LED for extended module slot 1 (8) LED for extended module slot 2

(9) Mode LED (10) Mode button

Figure 1-5 Front panel of the S5500-28C-EI-DC

1.3.3 Rear Panel

(1) (2) (3) (4) (5)(1) (2) (3) (4) (5)

(1) –48 VDC power socket (2) RPS port

(3) Grounding screw (4) Extended module slot 1

(5) Extended module slot 2

Figure 1-6 Rear panel of the S5500-28C-EI-DC

1.3.4 Power System

The S5500-28C-EI-DC can adopt DC input, or 12V RPS input, or both to provide

backup. Only the recommended RPS can be used.

z –48 VDC power input

Rated voltage range: –48 VDC to –60 VDC

Input voltage range: –36 VDC to –72 VDC

z RPS input

Rated voltage range: 10.8 VDC to 13.2 VDC

Installation Manual

H3C S5500-EI Series Ethernet Switches Chapter 1 Product Overview

1-9

1.3.5 Cooling System

The S5500-28C-EI-DC is equipped with four fans for heat dissipation.

1.3.6 LEDs

For descriptions about LEDs, see Table 1-4. You can switch the Mode LED display

mode between speed and duplex by pressing the Mode button on the panel.

Table 1-4 LEDs on the front panel of the S5500-28C-EI-DC

LED Mark Status Description

Speed Solid green Rate of the port

Mode LED Mode

Duplex Solid yellow Duplex mode of the port

Solid green

The switch is started

normally.

Flashing green (1 Hz)

The system is running a

power-on self-test

(POST).

Solid red

The system fails the

POST or a power failure

occurs.

Flashing yellow (1 Hz)

Some ports fail a POST

or a port failure occurs.

Power LED PWR

OFF

The power is

disconnected.

Solid green

The DC input is normal

and the RPS is

connected and works

normally.

Solid yellow

The RPS input is

normal, but a DC input

failure occurs or no DC

power is connected.

Redundant power

system LED

RPS

OFF No RPS is connected.

Solid green

The module is in

position and works

normally.

Flashing yellow

The switch does not

support the module or a

module failure occurs.

Module LED MOD

OFF No module is installed.

Installation Manual

H3C S5500-EI Series Ethernet Switches Chapter 1 Product Overview

1-10

LED Mark Status Description

POST

running

The power

LED flashes

green

The LED displays the

POST test ID.

POST

failed

The power

LED flashes

red

The LED flashes the

POST test ID of the

failed test.

Software

loading

The power

LED flashes

green.

A bar rotates clockwise

around the LED.

Fan

failure

The power

LED is solid

red.

The LED displays F.

Over-tem

perature

alarm

The power

LED is solid

red.

The LED displays t.

7-segment digital

LED

Unit

Cluster

state

The power

LED is solid

green.

For a command switch,

the LED displays C.

For a member switch,

the LED displays S.

For a candidate switch,

the LED displays c.

The LED displays 1 if

there is only one unit.

Installation Manual

H3C S5500-EI Series Ethernet Switches Chapter 1 Product Overview

1-11

LED Mark Status Description

Green

A 1000 Mbps link is

present. When data is

being received or sent,

the LED flashes at a

high frequency.

Yellow

A 10/100 Mbps link is

present. When data is

being received or sent,

the LED flashes at a

high frequency.

Flashing

yellow (3 Hz)

The port fails the POST.

Speed

OFF No link is present.

Green

The port works in the full

duplex mode. The LED

flashes at a high

frequency when data is

being received or sent.

Yellow

The port works in the

half duplex mode. The

LED flashes at a high

frequency when data is

being received or sent

Flashing

yellow (3 Hz)

The port fails the POST.

10/100/1000Base

-T port status LED

—

Duplex

OFF No link is present.

Green

A 1000 Mbps link is

present. When data is

being received or sent,

the LED flashes at a

high frequency.

Flashing

yellow (3 Hz)

The port fails the POST.

SFP port status

LED (1000 Mbps)

—

The

Mode

button

has no

effect on

the LED.

OFF No link is present.

Installation Manual

H3C S5500-EI Series Ethernet Switches Chapter 1 Product Overview

1-12

LED Mark Status Description

Yellow

A 100 Mbps link is

present. When data is

being received or sent,

the LED flashes at a

high frequency.

Flashing

yellow (3 Hz)

The port failed the

POST.

Speed

OFF No link is present.

Green

The port operates in the

full duplex mode. When

data is being received or

sent, the LED flashes at

a high frequency.

Flashing

yellow (3 Hz)

The port fails the POST.

SFP port status

LED (100 Mbps)

—

Duplex

OFF No link is present.

1.4 S5500-52C-EI

1.4.1 Appearance

The S5500-52C-EI provides forty-eight auto-sensing 10/100/1000BASE-T Ethernet

ports, four 1000Base-X SFP ports, and one console port on the front panel, and one AC

power socket, one RPS port, and two extended module slots on the rear panel.

Figure

1-8 shows the appearance of the S5500-52C-EI.

Figure 1-7 Appearance of the S5500-52C-EI

Installation Manual

H3C S5500-EI Series Ethernet Switches Chapter 1 Product Overview

1-13

1.4.2 Front Panel

(1) (2)

(10)

(3) (6)

(7)

(8)

(9)

(4) (5) (1) (2)

(10)

(3) (6)

(7)

(8)

(9)

(4) (5)

(1) Auto-sensing 10/100/1000Base-T Ethernet port status LEDs

(2) Console port (3) 7-segment digital LED

(4) Mode button (5) Mode LED

(6) Power LED (7) RPS LED

(8) LED for extended module slot 1 (9) LED for extended module slot 2

(10) SFP port status LED

Figure 1-8 Front panel of the S5500-52C-EI

1.4.3 Rear Panel

(1)

(2)

(3)

(4)

(5)

(1)

(2)

(3)

(4)

(5)

(1) AC power socket (2) RPS port

(3) Grounding screw (4) Extended module slot 1

(5) Extended module slot 2

Figure 1-9 Rear panel of the S5500-52C-EI

1.4.4 Power Supply System

The S5500-52C-EI can adopt AC input, or 12V RPS input, or both to provide backup.

Only the recommended RPS can be used.

z AC power input

Rated voltage range: 100 VAC to 240 VAC, 50 Hz or 60 Hz

Input voltage range: 90 VAC to 264 VAC, 47 Hz to 63 Hz

z RPS input

Rated voltage range: 10.8 VDC to 13.2 VDC

Page is loading ...

H3C S5500-28F-EI Installation guide

This manual is also suitable for

H3C S5500-28F-EI Installation guide

Related papers

Other documents